Taipan Veteran Power Plenum - regulator extender Install

[@randycombs112]

Thanks for your time into this for other's. I have a question. I also have the same, but mine came with a power plenum tune from Tony at Talon Tunes. It was getting 62fpe with Jsb .34gr and hammer spring one turn from max. It was pretty consistent in it's 40 shot string. I wanted a bit more for slug shooting, so I got the power spring from Tony too. I noticed you mentioned in a comment that you have your power spring maxed out. Are you getting good consistent shot strings? I'm not. At max mine started at 974fps (70fpe!) And would quickly start dropping to 930 in 10 shots. Then I set out to turn tension back down using 1/4 turn to find some consistency. Bunch of pellets and refills later I still can't get real good shot strings. Even took the hammer tension way down in fps. Here's where I brought it back up to that was best I was getting. Even did 10 sec wait between shots for reg. 34gr Jsb string. 1.935 2.946 3.944 4.958 5.940 6.942 7.935 8.935 9.930 10.956 11.937 12.946 13.956 14.926 15.944 16.949 17.946 18.923 19.930 20.926 21.935 22.942 23.928 24.937 25.942 26.930 27.930 28.923 29.909 30.909 fps String with VK 32.8g slugs 1.921 2.949 3.943 4.932 5.949 6.930 7.937 8.932 9.932 10.946 11.949 12.946 13.930 14.928 15.942 16.937 17.937 18.935 19.937 20.939 21.939 22.921 23.939 24.944 25.926 26.918 27.914 28.926 29.923 30.898fps I'd appreciate your thoughts on this. Thanks!

[@ianprice2441]

Can't wait!!! 👍

[@chrisfigueroa3361]

That thing is badass brotha

[@dougdishler2086]

Great video man

[@havenmaine143]

Nice review buddy.and you sound like a young jigsaw.i was just waiting for you to say (I'm going to give you a choice)

[@craigcrosby1656]

It would have been so much better to work on a table, work on a light surface, and zoom in your camera. But thanks for the insight.

[@budgetdownproductions9045]

Agreed.. 2 years is a long time.. thanks for watching,.

[@airgunspasion5158]

hello with huma regulator plus taipan long .25 power plenum in how many bars would you leave the huma regulator?I appreciate your response

[@FirstStateAirgun]

Dam i need just 1 PCP. Nice video.

[@chrisfigueroa3361]

How much longer is the tube now that you installed plenum ...and how do I get a hold of Ernest rowe thanks so much

[@budgetdownproductions9045]

Chris Figueroa I’ll send pm

[@budgetdownproductions9045]

go to bay and search taipan veteran it will show up..

[@nicholasswann5254]

I just got a veteran long .25 that I haven't even shot yet. Is there anything I should/could do to get the best accuracy possible without a chronograph?

[@budgetdownproductions9045]

You really need a chronograph.... But, I would adjust the hammer spring until it is the most accurate.. Mine likes the hammer spring almost maxed , and stock regulator settings.. Shooting 34 grain slugs out to 200 yards”””””” and 34 grain pellets out to 100 yards accurately.. The plenum extension makes the shots more accurate than ever before, almost like each shot has less turbulence, about a 10 second recovery in between shots for the regulator to recover...

[@svilenp]

Hello, good job! I have the same rifle from last summer :) Can you tell me where I can buy the same?

[@budgetdownproductions9045]

eBay.. Search taipan veteran The plenum will show up

[@svilenp]

@@budgetdownproductions9045 Thanks. There may have been but now there is no (in ebay, amazon...)... I have some questions and if you wish you can give me an option to contact you / writing not a phone /? Regarding this video, our Russian colleagues say that before the whole "Picatinny rail" module is tightened, the tank should be filled up to 260 - 270 bar, otherwise there will be a difference in the average hit point - What do you think about that?

[@budgetdownproductions9045]

They are still there on eBay More than 10 left.. Search Taipan vetern It’s not spelled correctly Hope that helps..

[@budgetdownproductions9045]

I don’t fill it until it’s Back together, I dint know how that could possibly affect accuracy..

[@svilenp]

@@budgetdownproductions9045 Thanks for your reply. Regarding what the Russians are saying, I suppose they have in mind that when the "module" is tightened (maybe more ...) then when filling the tank it can lead to "displacement" of the module together with the optics (though a little) and this would affect the zero setting of the optics ... of course this has a problem with all rifles where the barrel contacts the butt or the tank (except the point of connection with the barrel box). That's how I think, even though I'm not an expert. As for "plenum" - I tried several options but nothing worked out. I guess maybe because I'm from Bulgaria ... if you want to copy the link?

[@kostasgold]

I cant hear you