Taking apart a HIWIN HGH15CA linear guide rail carriage - bearing replacement and service part 1

  Рет қаралды 24,053

Roadside jobshop

Roadside jobshop

Күн бұрын

Пікірлер: 41
@kandrkandr
@kandrkandr 3 жыл бұрын
I used one of those pick up magnets on a pole. They just pop back in. Use a small screw driver to push them. No need to open it up. I got lucky. Found them all.
@michaelkelly3158
@michaelkelly3158 5 жыл бұрын
The manual says you need to push a hot rod through 'the bottom of the tapped hole' to be able to grease the block. Is that white plastic diaphragm what they are talking about pushing the rod through?
@urgamecshk
@urgamecshk 7 жыл бұрын
Same situation right now.... One ball left to find!
@bblloobb1000
@bblloobb1000 3 ай бұрын
Well, today by mistake, tried to grease the hg15ca when was out of rail but with protector. however, some balls pop out. tried to fixed, but cant understand the righ side and position to those short black plastic-bracket, that stays from both side inside.they are flat from one side, chanel otherside.what is propper position.flat side out or in
@nuxrohox-cortx-6222
@nuxrohox-cortx-6222 Жыл бұрын
how many steel balls are there in total?
@RebelBlades
@RebelBlades 8 жыл бұрын
I would just buy a new one ! Screw the bearings ! But that is just me. I am looking forward to seeing you finish the surface grinder !
@gentiligiuliano7882
@gentiligiuliano7882 4 жыл бұрын
Did you find replacement balls?
@patrickdunne4975
@patrickdunne4975 3 жыл бұрын
Where is part 2? or is this a joke
@cncart
@cncart 3 жыл бұрын
@@patrickdunne4975 guess he didn't find the balls lol
@jamescullins2709
@jamescullins2709 3 жыл бұрын
I may be a little off topic but some of the Chinese talk about a square carriage. What do they mean? I don't see the difference
@WarThunderGerald
@WarThunderGerald 4 жыл бұрын
Did you ever find a replacement bearing orderable online? If so could you link info for it?? Hoping to find one for my (non genuine) variant of this that is one bearing short on one block - so annoying!
@mariuspetcu7482
@mariuspetcu7482 3 жыл бұрын
Thank You ... and to be critic (LOL) light must be on your right hahaha ... again Thank You
@mikeylama
@mikeylama 6 жыл бұрын
Hi, where have you accessed the technical data of the bearing balls? I'm quite desperate for them :D
@jasonb9629
@jasonb9629 2 жыл бұрын
So what exactly is the deal here? Is that re-assembly video ever coming??? They are not exactly complicated devices I just wanted to be sure I am doing it right. Those 2 plastic pieces that go on the inner sides of the carriages I just cant figure out how they are held in place. Other than that I think I am okay.
@zwerne42
@zwerne42 7 жыл бұрын
Can you give me an idea of how much load these 15mm rails/blocks can support? Or how well they compare to sbr20uu? Thanks for the video
@roadsidejobshop9287
@roadsidejobshop9287 6 жыл бұрын
These bearing blocks are very much stronger compared to SBR20UU, because they have more ball bearings and the block supports the load better. But using linear rails, you have to have a much more accurate setup for the machine in general. SBR20UU tolerates some inaccuracy in parallelism and being unplanar a little bit, linear rails dont like it at all.
@zwerne42
@zwerne42 6 жыл бұрын
Nice to know that. I will make a new structure using my already built CNC router when I get to upgrade to linear blocks. Thanks for replying
@roadsidejobshop9287
@roadsidejobshop9287 6 жыл бұрын
Whats the machine you are building`? upload some videos :)
@zwerne42
@zwerne42 6 жыл бұрын
Just a CNC router, Thinking about upgrading it to the linear blocks at a later time. Might post a video later :)
@Correllbil
@Correllbil 2 жыл бұрын
Looks like the bearings are 1/8".
@FriedrichKegel
@FriedrichKegel 7 жыл бұрын
Thank you a lot for this video, helped me much to clean up my chinese MGN12 :) Mine are sticking a bit only in one direction, do you have ideas what the reason might be?
@roadsidejobshop9287
@roadsidejobshop9287 7 жыл бұрын
I would check if you don't have any dents in the rails - some of the cheaper MGN's have dents and scratches. If you do - buy some precision stones and lightly clean the surface.
@FriedrichKegel
@FriedrichKegel 7 жыл бұрын
Thank you very much, i think you are right there are some micro-dents on the boarder of the cylindrical surface where the balls move inside. First I will try to run them in for some hours, maybe the problem is solving itself.
@danielmattsson8574
@danielmattsson8574 7 жыл бұрын
How to put it back together? :)
@roadsidejobshop9287
@roadsidejobshop9287 7 жыл бұрын
I'm planning on making the video about that in a few days... :)
@urgamecshk
@urgamecshk 7 жыл бұрын
Roadside jobshop well???
@michalycz
@michalycz 5 жыл бұрын
@@roadsidejobshop9287 did you succeed in putting it together?
@ScottyDoesntKnow321-
@ScottyDoesntKnow321- 5 жыл бұрын
@@michalycz Legend has it he's still trying to get the balls back in XD
@TheBeardedBoofhead
@TheBeardedBoofhead 4 жыл бұрын
@@ScottyDoesntKnow321- Aren't we all... :D
@gungov2024
@gungov2024 4 жыл бұрын
Just lengthening the video and wasting time with his hmms hahs well so right. Very little sustance for a 19minute video
@seasonsunite
@seasonsunite 6 жыл бұрын
I didn't get it, do you recommend buying these or not? Longest review ever
@WarThunderGerald
@WarThunderGerald 4 жыл бұрын
it's clearly NOT a review video ... If the Title didn't already give that away ...
@boucha18
@boucha18 8 жыл бұрын
1/8" = 3.16mm
@roadsidejobshop9287
@roadsidejobshop9287 8 жыл бұрын
Yep, it's actually 3.175mm. I ordered the new balls and will be re-packing them in just a few days - video incoming soon :)
@WarThunderGerald
@WarThunderGerald 4 жыл бұрын
@@roadsidejobshop9287 Hey will you share video on that? I was just about to order 1/8th inch bearings but - Will they absolutely not work / must be 3.175mm?
@molitovv
@molitovv 8 жыл бұрын
Tweezers!
@roadsidejobshop9287
@roadsidejobshop9287 8 жыл бұрын
Absolutely correct - gold star for you :)
@MrEarnxtracash
@MrEarnxtracash 4 жыл бұрын
Jesus, less opinion and building info and show how to rebuild the damn bearing... LOL
Tuning Up Cheap Chinese Linear Bearing
7:59
MrDabrudda
Рет қаралды 350 М.
Improving dirt cheap linear rail guides & blocks
9:16
Dirk Herrendoerfer
Рет қаралды 70 М.
СИНИЙ ИНЕЙ УЖЕ ВЫШЕЛ!❄️
01:01
DO$HIK
Рет қаралды 3,3 МЛН
Что-что Мурсдей говорит? 💭 #симбочка #симба #мурсдей
00:19
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН
Roller Rail RSHP | Proper Lubrication of Runner Blocks
2:09
Bosch Rexroth US
Рет қаралды 27 М.
Knife Like Razor Sharp! Sharpen Any Knife in 1 Minute with an Old Battery
10:12
Linear Guide Maintenance DIY
15:36
JBWorxStudio
Рет қаралды 18 М.
How We Made Incredible Single Helical Gear For Industrial Machine Process ||
27:16
Mounting Hiwin guideway
3:20
Vansichen Linear Technology
Рет қаралды 73 М.
IKO Linear Ways: Mounting Methods (High Accuracy, High Rigidity)
6:41
IKO International, Inc.
Рет қаралды 86 М.
How to install NSK Linear products - 2. Ball Screw
14:39
NSKMotionAndControl
Рет қаралды 1 МЛН
Linear Rail Lubrication
7:01
Kapman's Basement Workshop
Рет қаралды 32 М.
СИНИЙ ИНЕЙ УЖЕ ВЫШЕЛ!❄️
01:01
DO$HIK
Рет қаралды 3,3 МЛН