Tamiya Mini 4WD - Mach Frame Advance Stock Build + Test Run

Video on how to build Advance Stock setup for Mach Frame (FMA)
Parts with Item number for reference
FRP Multi Roll Setting Stay (15394)
Large Dia. Stabilizer Head Set (17mm) (Purple) (95519)
Jr Adjustable Mass Dampers 2.5G Weights X6/Silver (95608)
Stainless Steel Screw Set (15/20/25/30mm) (15508)
Front Under Guard (15405)
Side Mass Damper Set - AR Chassis (15459)
FRP Wide Rear Plate (for AR Chassis) (15452)
Low Friction Roller Set (15381)
Aluminum Spacer Set (12/6.7/6/3/1.5mm) (15473)
Brake Set (for AR Chassis) (15458)
Torque-Tuned 2 Motor (15484)
Basic build Mach frame (FMA) BMAX by Panda_mini4wd
fb.watch/oHDcf...
Dont forget to like, subscribe and share.
Connect with me!
- Facebook: DEE Mini 4WD PH
- Instagram: deemini4wdph
- KZbin: DEE Mini 4WD PH

[@NashCastanares]

Nice build! Though this will be disqualified in TMAC. You can only use 2 sets of frp plates (side dampers are considered as one set). Your kit uses 3 frp sets - front, side, rear.

[@DEEMini4WDPH]

Thanks nash for your comment. But last time I checked they allowed 3 frp sets for tmac category. I’ll check it again just to be sure 👌

[@RDPRNT]

TMAC now allows up to three sets of frp based on lils hobby center website

[@DEEMini4WDPH]

@@RDPRNT thank you. Too bad not much tmac races nowadays :(

[@NashCastanares]

@@DEEMini4WDPH nice! buti pwede na 3 FRPs. Thanks! Di rin ako aware na updated na yung rules for TMAC, more on BMAX ako recently. Happy racing boss!

[@DEEMini4WDPH]

@@NashCastanares happy racing too!

[@geloromasanta2354]

Almost ganto rin setup ko sa mach frame ko pero 13 mm tas small stabilizers front tas may breakpad sa baba. Frp break, cylinder tas ar frp mid, frp break tas torque tuned 2. Iba hatak ng torque tuned vs rev tuned.

[@geloromasanta2354]

D ko sure if 13mm sukat bsta ung maliit na kasama malaking violet. New lng dn kaya d ko pa alam terms. Ung mga bmax user nabbilisan sa gantong srtup.

[@DEEMini4WDPH]

Nicenice :) pero not sure sir if allowed nila sa race ung may frp sa harap as front brakes like sa bmax setup. Naisip ko din gawin date yun pero meron kc nagsabe sakin not allowed daw kaya front underguard nalang ung nilagay ko

[@DEEMini4WDPH]

Yiz i think 11mm yung kasama nun. Mabilis din hatak ng torque tuned motors. Meron nga videos si @exaflare23 na torque motors gamit nya

[@GeloHobbies]

Hi just getting into the hobby. Am I allowed to change the shafs and crowns for the car? my current wheel shaft is crooked and thinking of using a reinforced or hallow shaft. Thanks dude.

[@DEEMini4WDPH]

Hi. Yes you can change gears and crowns just follow the correct combination. For the wheel shaft i’m not sure if Reinforced shaft is allowed. Better to use the regular one

[@GeloHobbies]

@@DEEMini4WDPH thanks bro! I hope you don't mid i copied your build!

[@DEEMini4WDPH]

@@GeloHobbies yes sir no problem :) have fun racing!

[@relawanengineering]

Hello. Ano usually chassis na gamit pag stock advance? Or palag naman kahit ano? Hehe Salamat po

[@DEEMini4WDPH]

Hello sir, kahit anong chassis po palag naman pero usually nakikita ko ngppodium is S2, FMA and MA chassis. Lamang si S2 kasi sobrang gaan nya ska design for speed talaga.

[@johnchavez1776]

Saan po link ng stock advance/tmac guidelines? Thanks sir

[@DEEMini4WDPH]

@@johnchavez1776 hi sir. www.lilshobbycenter.com.ph/pages/stock-advance-rules-and-regulations

[@johnchavez1776]

@@DEEMini4WDPH thank you so much sir 😁

[@DEEMini4WDPH]

@@johnchavez1776 you’re welcome

[@louiebanal6421]

Can we use mach frame for pro stock?

[@DEEMini4WDPH]

Yes sir. But most of the prostock races now are non-fm.

[@louiebanal6421]

@@DEEMini4WDPH why is that? What's wrong with fma chassis

[@DEEMini4WDPH]

@@louiebanal6421 fma chassis has an advantage over non-fm in prostock category that’s why prostock races is divided into 2 categories.

[@louiebanal6421]

@@DEEMini4WDPH thanks

[@flyffrm6951]

Ano po gear ratio

[@DEEMini4WDPH]

Hi sir 3.5.1 gear po

[@flyffrm6951]

@@DEEMini4WDPH ask ko pala po kung need nka counter sunk mga screw pati sa side frp

[@DEEMini4WDPH]

@@flyffrm6951 kahit regular screw lng po pwede na as long as may 1mm ground clearance.

[@ixncxrl6627]

I would be disqualified if i dont have front under gueard

[@DEEMini4WDPH]

Oh really? I didn’t know that.. i think it depends on the racing center as each one is different from another. But most of the time I see racers put on front under guard. This will be their brakes when hitting the slopes

[@ixncxrl6627]

@@DEEMini4WDPH its a question hehe. I am planning not to put one and will focus on speed

[@DEEMini4WDPH]

@@ixncxrl6627 oh sorry about that :) yes you have the option not to use underguard in races