Simple, straightforward, 2 and ½ minutes, how could anyone ask for better, thank you for showing me the answer without wasting my time, 11 out of 10 and exceptional, thank you 😎👍🏻
@godsparticle76578 жыл бұрын
thanks bro ! very informative video ! u could have also showed the direction of turning of angle and how it affects the workpiece (to start from smaller DIA end or at larger DIA end )
@kenzpenz9 жыл бұрын
Great video, and I will be using this information on my project. One question though, what determines the angle that is set on the compound. I want to end up with a I/2 in end on the small end and 7/8 ' on the large end with an overall length of 1 1/8 long on the knob I am making.....Thanks ...Ken...Marina CA
@HugoMak9 жыл бұрын
Kenneth Bartlett Simple trigonometry
@kenzpenz9 жыл бұрын
Kenneth Bartlett Oh yeah thanks...I should have know. What was I thinking. it's simple trig. You are the master of the universe. With this helpful insight people will flock to you. NOT !
@mohammedazarudeen79008 жыл бұрын
+Kenneth Bartlett ( D1-D2)/2L, where D1 is large diameter, D2 is smaller diameter and L is length which you want taper. here you go.......
@Bilalkhan-lk9hv7 жыл бұрын
D-d/2l multiply by tan inverse u will get the angle theta
@shubhamwr5 жыл бұрын
Kenneth Bartlett of course it's angle at which u need to taper. How r u going to use his angle u should know it urself . Either u should directly know angle of taper or two diameter from original dia and final reduced dia. Then use trigonometry to find taper angle from that
@myambedkarnagarisgreat35273 жыл бұрын
Sar ham kaise check karenge ki kitne degree par lagana hai cut taper
@RustyInventions-wz6ir10 ай бұрын
Just found your channel and Subscribed. Nice work.
@chetugatty97997 жыл бұрын
Sir! You turned the compound slide right side what happened if you turn it left side plzzzzzz tell me
@shubhamwr5 жыл бұрын
Chetu Gatty it must be turned to right side due to cutting edge of tool
@mithunantony58015 жыл бұрын
How to find required angle ?
@pauls57454 жыл бұрын
kind of like an overview, not exactly in depth guide, but somewhat helpful
@vinayakadalwai40729 жыл бұрын
thanks for the video.. can u show how to do thread cutting in the same lathe machine
@birhoff11 жыл бұрын
Man, I owe you one. Thanks !
@akhilakhi63617 жыл бұрын
Sir please add all the videos operations about the direction of feed and depth of cut in different operations
@myambedkarnagarisgreat35273 жыл бұрын
Sar ham isko check kaise karenge
@1alphasam4 жыл бұрын
Song?
@Jackknifegyp11 жыл бұрын
Internal Taper??
@YinYangDPW2 жыл бұрын
Use same compound setting as for external taper, switch to cutting on the back side while running lathe in reverse. Results in internal female taper that matches angle of external male taper.
@hendywijaya28664 жыл бұрын
thanks for the video !
@davidtuppenney94547 жыл бұрын
Remove your watch!
@iraqresitance96633 жыл бұрын
From iraq well done
@PacoOtis7 жыл бұрын
Why no narration? Don't you know enough about what you are doing to explain it? Of course you do! Please change your format and best of luck.
@WilleJamesHuff5 жыл бұрын
Joseph Stokes if you have used a lathe with even basic skills you shouldn’t need any help. I watched it with no sound and understood it perfect