Good reference point for timing video for the m276 motor
@FirearmTutorials7 жыл бұрын
Thanks for making these videos. Maybe soon I'll be brave enough to work on my own M156.
@SlickJeff20207 жыл бұрын
Hi Tasos, can you conform if those 4 pulleys are new or your using the old ones and also if you deem necessary to use new coils After a full rebuilt like this. Thanks a bunch
@TasosMoschatos7 жыл бұрын
+Jane Dogh Hi, if they are healthy I'm using the old parts. Keep in mind that if there is any problem with the old ignition coils you can change it later it's better to spend 20 more min than to throw 8 healthy coils
@glasser28194 жыл бұрын
If your coils and plugs are good but you positively FEEL RANDOM MISFIRES AT COLD IDLE without any "misfiring DTC"... then consider this solution: Any odd CAN-Bus module DTC may introduce SLIGHT DELAYS in the engine ECU firing. O2 sensor will detect unburned gas and lean out your mixture making firing even more difficult. The timing delay + lean mixture will create a slightly laggy throttle response. It will be "acceptable" but not great. To restore the engine crisp response... FIX ALL MODULES DTC (or RESET ALL DTC for testing) then consider resetting the engine ECU to speed up relearning the FUEL TRIM map from an unbiased default map. Even a ridiculous chassis DTC such as a "bad tail bulb" on rear SAM can introduce this timing delay. It is also incremental: more DTC, more delay. Knowing Bosch CAN-Bus design this driveability bug may well be one of their money maker. It is IMPOSSIBLE for engineers to have never seen this bug introduce delayed response and engine shakiness without code. CAN-Bus architecture is built around DISTINCT BUSES to prevent this class of problem... "the Best or Nothing" 😂 More power to you! 👍
@kalamata71 Жыл бұрын
Γεια σου Τάσο θα ήθελα να σε ρωτήσω μια ερώτηση για Ε550, Μερσέντες μηχανή M278 έχεις φτιάξει βίντεο πώς να αλλάξεις τα γρανάζια και το Πιν που χαλάνε σ’ αυτές τις μηχανές σ’ ευχαριστώ για τα όλα τα βίντεο που φτιάχνεις είσαι τρομερός και είμαι συνονόματος Τάσος αν μπορέσεις να Μου στείλεις ότι βίντεο και ότι απαντήσεις για αυτή τη μηχανή είναι διπλό τουμπαρισμένο και θέλω να αλλάξω τα γρανάζια που είναι μπροστά στα camshaft phasers ευχαριστώ φίλε μου στείλεις ότι βίντεο ή ότι information μπορείς Για αυτή τη μηχανή. Σε χαιρετώ από το Brooklyn.
@alexmair36134 жыл бұрын
Love your videos on the M157 monster motor. Dream to own this car (E63 AMG) after passing the USMLE Step 1 (test to become doctor in the U.S.). That engine albeit its not hot v turbo, has such a growl and insane power potential (i.e from the likes of Weistec). Great work!!
@jameslatimer14324 жыл бұрын
Designed to fail. And drop you in the CRAP
@alexjoe15222 жыл бұрын
good morning my name is Alex I like to join your company
@jameshough20014 ай бұрын
can the bank 1 intake cam adjuster be replace without removing the valve cover when replacing chain tensioner?
@TasosMoschatos4 ай бұрын
Yes
@abatherzidan936210 ай бұрын
Hello tasos I have done same way that you do the time but , when I but the crankshaft at 53 degrees to check the timing from the top it doesn't give me half moon for the camshaft signal plate can you advise me please, by the way I have replaced the timing chain the camshaft adjusters but I keep the camshaft
@Satkacturk2 жыл бұрын
I have 2012 mercedes S550 ,4 magic. Problem left side driving side Camshaft my machine is 2780501347 can i put 2780501547 il. could there be problems?
@iliesirbu9672 жыл бұрын
❤🔥😍 this video saved me, I had to do it twice because alldata shows wrong timing marks i spend 3 days until i decided to check youtube, i have 6years bmw/mercedes experience but this engine its my first time God Blees You for recording This Video Thank you very much
@TasosMoschatos2 жыл бұрын
kzbin.info/www/bejne/qnWbqpaaftt6sLc
@gayantissera60922 жыл бұрын
Thank you for the video.. My m276 engine timing marks are ok at 40dig. But at 53dig the reluctor plate won't stay in the mid bore. Any reason for that. ?
@markspagnol5892 жыл бұрын
Hi can you give me the tightening torques for the main caps and big ends for the M157 engine Thanks
@robert618mcguire4 жыл бұрын
Do u have an videos on m276 timing !!!! Bank 2 ?
@andreteixeira78802 жыл бұрын
Hello my friend. It's possible change the timing chain and guides without taking off the cylinder head?
@PJ-xl7nb2 жыл бұрын
Tasos, can I send you 4 photos of my M276 timing setup ?
@58fins2 жыл бұрын
Love this video! I just had a problem with an M278 and I ended up one tooth off on the exhaust cam, bank 1. The factory laser marks are on the back of the cam, where you can't see them with the valve cover on! The timing marks on the old M272/M273 were better, to be sure! Thanks brother, from a fellow MB tech in USA!
@walmahmood Жыл бұрын
Like your explanation it’s very much clear.
@iPrimeYTTM9 ай бұрын
I have a rattle sound upon startup? The camshaft acutator could this be the issue?
@Tunez19766 жыл бұрын
Hi, Tasos. Could you tell me please, on a pulley placemark factory ? Or did you put them yourself? And another question. The tensioner, put new, but were not included on labels. You can re-use the tensioner after removing ?Thanks
@user-rt7gc5dn5s5 жыл бұрын
Why there are no clear marks it's a work and not a puzzle Mercedes engineers are crazy now it's Timing markes very bad bolt in their ass
@honnarhonnar61396 жыл бұрын
Hello mr tasos moschatos thank you very much for your video .. i hAve one 278 engine I just working here in my work .. and the reason is one timing chain was broken what should’ I recommend thank very much sir ..
@fuadbayraml33413 жыл бұрын
Hi is it still same with m276? I think should be T/0. Is it right?
@BadAssEngineering4 жыл бұрын
Great Videos on Timing! But what are the Cylinder Numbers? Are they like an american engine in which the Cylinder Number 1 is the closest to the timing chains? Like one cylinder head has 1357 and the other 2468? Or are cylinders in one bank considered as 1234 and the cylinders on the other banks 5678 ??
@TasosMoschatos4 жыл бұрын
Hi, bank 1 pass side = 1234 & bank 2 drivers side= 5678
@ИгорьСкорб-п1с6 жыл бұрын
Hello! Tell me, at М276 the motor, so I will look labels chain?
@umorunathaniel60544 жыл бұрын
V6R
@Bossy23 Жыл бұрын
it's really confusing... I've done it this way and other ways and still don't line up in the sensor hole... Do you know what could possibly be the problem? Thank you
@ShukhevichRecords3 ай бұрын
Shifted impulse plates
@garyrytlewski77325 жыл бұрын
I have a 2014 S550 (222.185) v8-4.6L turbo (278.929) will this timing set up work for my engine? the timing marks appear to be in the same locations but im getting a bank 1 camshaft fault after putting new adjusters on the passenger side intake and exhaust. If you look at live data then bank one inlet cam goes to 46' as soon as engine is started and does not adjust at all
@glasser28194 жыл бұрын
did you figure what was wrong??
@affenkakke20 Жыл бұрын
Ist it the same on the M276 engines ?
@Williow20792 жыл бұрын
You know you can just check basic set timing by checking your Hall Sensor's and making sure it lines up in the middle. If you read the manual there is a section that tell you where the marks have to line up when you are looking down the hall sensor hole! This will be for the M276 & M278 engines.
@TasosMoschatos2 жыл бұрын
kzbin.info/www/bejne/qnWbqpaaftt6sLc
@prozzyit6 жыл бұрын
Hello Tasos, I changed 4 cam adjuster and chains on m276 ,2011. But I didn't changed the tensioner. Now , my timing is out... should I need to change tensioner.... and is anything to do with bottom gear....
@glasser28194 жыл бұрын
why keep bad old tensioners? The main culprit seems to be low pressure from low oil viscosity that works out the pin of the passenger intake adjuster... use 10w40, not 5W30 👍
@costabravaamine7262 Жыл бұрын
C'est quoi comme logiciel ?
@fanaldinho92553 жыл бұрын
Tell me more
@ndubuisiigbokwe45682 жыл бұрын
Wot of 276
@rezaul74126 жыл бұрын
Sir i want m276 timing chain with camsept timing.
@burken99626 жыл бұрын
Süper thenx captain
@ROMA2MECANICA3 жыл бұрын
How much is a job on bend valves
@alexjoe15222 жыл бұрын
I'm a Mercedes mechanic
@Nadeerizahmad5 жыл бұрын
👍👍👍👍👍
@femiesan42615 жыл бұрын
271
@femiesan42615 жыл бұрын
mb 271
@abatherzidan93623 жыл бұрын
That is wrong the timing shown on the computer which you have done is for the m276 which is 6 cylinder the m278 is 8 cylinder which is the other one that showes in your computer at 3:57 the points most be towards the out not in .
@TasosMoschatos3 жыл бұрын
are you sure about that? Do you want me to answer or you want to search it little bit more and correct your comment?
@TasosMoschatos3 жыл бұрын
I'll help you little bit, the crankshaft have 720°
@Draginev3D3 жыл бұрын
You could clearly see the validity for the Engines: 152.9, 157, 276, 278. Correct me if I'm wrong Tasos! But it's indeed confusing when pictures shows that it points outward hehe.
@abatherzidan93622 жыл бұрын
@@TasosMoschatos hey tasos and also iron , I want to say thank you first for your videos I'm doing my engine m278 as well you helped me a lot thanks man , yeah for the timing again so there is as you see on the computer I have the Mercedes program as well I have looked at it to may times and if I'm not wrong you can see there is 2 different pictures one pointing in words the other to the out and one of them for m157/m278 the other one for m276 , other wise they can't be right both for the same engine so , if you look on the pictures the first one it says showing on the engine m278 and the points pointing out words + the timing chain it self comes with yellow points from Mercedes I think clearly for the points on the camshaft, but anyways, if I'm wrong please explain for me the page (ar05.10-P-7620-40mm) which is for timing the same page you showing on the video why there is a picture showing the timing marks to the out words . Thank you guys will wait for your reply, and sorry man for late answer I really just saw the reply from you , all the best 🙂
@abatherzidan93622 жыл бұрын
kzbin.info/www/bejne/lZiXpXhrYph_l68 If you see this video I think you would know what do I mean, unless I miss something those 2 videos contradict each others yeah ?
@DinoAutoupdate3 жыл бұрын
Bro you are a good engineer but keep cigarette aside before you explain
@danbiko24684 жыл бұрын
Thank you for the video but your timing is off. You are supposed to be at 53 degrees after tdc. If the crank doesn’t have that marking you are supposed to measure 17mm after the 40 degrees tdc and that’s gonna be your Mark for timing.
@gussingh39483 жыл бұрын
53° ATDC is not for setting cam timing. It is for inspecting the basic position of the camshaft through the position sensor holes.