Totally like your video. Very straightforward. I am using an H17120434 6 wire stepper motor. Your code functioned perfectly. Thanks for the effort you put into this video.
@michelecamarda72012 жыл бұрын
I have searched through so much reference, this is the best code available online regarding this matter! Thank you mister.
@DragonVisit Жыл бұрын
Thanks ... exactly what I was hoping to find. 🙂 Just so you know, you can save yourself a tiny amount of hassle in your FOR loop by doing this ... for (int i=0; ... instead of coding a whole line just to define 'i'
@marinilsonmoreira2 жыл бұрын
Muito obrigado meu amigo.....I am brasilian fã
@BrandegeePierce3 жыл бұрын
Thank you, sir... I am quite familiar with Arduinos and stepper motors but not so much stepper drivers. I have a rotary for a laser engraver and it is attached to a DM556 which is similar functionality to the TB6600. Randomly the rotary will start to just start rotating backward in the middle of job (the product on the machine is then garbage). After learning how the driver works, I realize 1 of 2 things is happening. The direction pin wiring is becoming intermittent or the internal connection of the driver for the direction pin is failing. Either way, I now know it is not the stepper motor or the software. It is either the wiring or the driver.
@victormonsalve1892 Жыл бұрын
thank you thank again GOD BLESS YOU thanks for sharing
@maxrybold1531 Жыл бұрын
I would like to see a "step motor", like this, that implements feedback control because all the tutorials for such set-ups are not that practical (unless the system requires continues motion).... Good job tho!
@RixtronixLAB Жыл бұрын
Creative video, well done, thanks for sharing it :)
@garylake93175 жыл бұрын
Good job. Right to the point.
@ernestarranzpasqual7167 Жыл бұрын
Great video! Can it be used for more than one motor simoultaneously?
@freytube110 ай бұрын
great video, keep doing it .. regards
@wassanadproject Жыл бұрын
digitalWrite(STEPPIN, !digitalRead(STEPPIN)); I don't understand. Please explain.
@zimbeats80943 жыл бұрын
Question: Does your method forward/reverse actually do just half the steps that you called for in the argument? Because for each "i" you only pull the STEPPIN either high or low, but not both. So instead you could correct the loop to : for(i=0; i
@Electronic-Journeys3 жыл бұрын
You are correct. The code should either include an on off toggle inside the for loop or a simple double count like you have shown to account the two transitions each pulse needs to make.
@olanordmann78369 күн бұрын
Do you have a video on how to take 3 of these and make a cnc machine?
@livinmarcenariaartistica82124 жыл бұрын
muito bom mestre, parabens
@kennethfajardo5121 Жыл бұрын
hello Sir i have a question I buy a stepper motor with current rating of 3 A then i also buy a TB6600 driver for the stepper motor that has a rating of up to 4.5 A. Im planning to power up the TB6600 with a 24V DC and 1 A. Since my motor need a 3A do I need a source (power supply) with 3A also or the driver will amplify the 1A if i power it with a 24V DC and 1 A?
@bobbys43272 жыл бұрын
I have this exact code but I get an error of: 'reverse' was not declared in this scope. ???
@umargul56442 жыл бұрын
Well done sir
@kusmanf3 жыл бұрын
Brother, I used a TB6600 driver with a Nano and wired accordingly and powered with a 12v,10A SMPS. I selected the current and steps/rev(200) with dip switches according to the specifications of the Nema 23 motor referring to the chart. When the motor runs at slow speed it gives a grumbling noise and gets heated up quickly. I tried with another Nema 17 motor with settings changed, still the same grumbling noise and heating. But I used a A4988 driver with the same Nema 17 motor, then it runs smoothly and does not get heated up. Could you advice me please?
@carloballot49272 жыл бұрын
Same here,:-( some hint would be great!!
@tiarekix4 жыл бұрын
Hi I have the same set up except for I'm using a 12v adapter but Icannot get it to work!!! can someone help me?
@repeters13 жыл бұрын
Hi, could you upload or send me the "modified" code? I took pictures of the code as you went through it but I keep getting an error at a "void reverse" section of the code. Thanks, Pete
@arduinomaquinas Жыл бұрын
Like 816 + subscribed ❤ 👏👏👏👏
@danilobelen15864 жыл бұрын
How do I increase the speed? Thanks
@jasoncreech44863 жыл бұрын
Yes how can I reduce the speed in your code?
@yudhavalkyrie75684 жыл бұрын
how to incrase speed?
@hemantha58652 жыл бұрын
How to use 6 pin nema 23 with this tute
@Omi1424 жыл бұрын
Name of the guitar track in background?
@lucabattistello12403 жыл бұрын
hi, very nice video, i have a question for you, i look your video and i make the configuration i proved your code non my arduin, but i have a problem , the motor don't work as in video , but it run only one direction , you can help me?