TBS Crossfire Series: TBS Nano Rx Setup Tips

[@harold1955]

Great work... How would I wire a nano receiver adapter( to leave in fuselage) separate from the nano rx ( placed on wing ).

[@Moonsauc3]

I think what you need is a tbs crossfire nano diversity rx adapter they're around 5$US but I think it only works with the diversity nano RX

[@just_bright]

I bought the nazgul5 with tbs crossfire and tango2 pro controller but cannot get the thing to bind. so frustrating

[@BlindedByEvil]

Was wondering if you have looked at the new TBS nano diversity? i read that it can have its own power supply and produce its own type of GPS with Lon/Lat and RF signal to pin point its location.

[@Painless360]

Not yet! :D

[@gregorydahl]

Can i bind my micro module tx with a reciever before putting it in the drone ?

[@Painless360]

I usually do that here to make sure that it is ok and that I can get to any bind button in case it is needed.. Happy flying!

[@RCdiy]

Glad TBS is doing well with their niche products.

[@mamoshimiloni9559]

IT IS 2022 NOW. I HAVE INVESTED IN CROSSFIRE EVEN THOU I HAD SOME LRS AND THAT IS WHAT I WANT TO USE IT FOR AND MY DRONES. ON MY DRONES EVERYTIME I WANT TO FLY ONE OF THEM I HAVE TO BIND THE THING again every time :) does anyone know why?

[@egtreadway4232]

Thanks for video, I'm confused on wiring from nano to f405-wing, I've updated firmware on micro tx v2 4.0.2- nano receiver 1.17. I've wired nano channel out 1 to uart rx1, channel out 2 to tx2 - 5v and ground same uart, no matter what I do it will not connect to any android app such as mission planner or Q controller. My question is should nano channel out 3 and 4 also be wired to a different uart to make this work. Thanks again

[@charlesdouyon5052]

thank you for reading this. I have a quick question. Can these TBS nano's be used to control and fly a stand 4 channel RC plane/jet?

[@Painless360]

Yes, with the PWM adapter board... Happy flying

[@antoineozaneaux6881]

hi painless I just received a rtf oblivion believe me it s not I may have put myself in the wrong region I tried to push the bind button more then 10 times but I wont let me access the general menu on the tx with tbs categorical refusal of helping people over the phone or hands on this little quad will be resting in it s nice case that it came with thank you

[@Painless360]

The reseller should be the first port of call for support or the TBS lounge is an excellent resource too.. best of luck!

[@jerryzito6840]

Thanks for the great video. I have the crossfire module on my TX16s. When I go to bind my quad, I get Tracer Micro tx which will not bind. Where am I going wrong?

[@Painless360]

You need the same module as the reciever in the model. Crossfire won't talk to Tracer recievers and vice versa.. Happy flying

[@tizianoluzi]

sorry my nano receiver has solid red light non the led and I cannot bind do you have any suggestion?

[@Painless360]

Could be a few things - what troubleshooting have you already tried?

[@tizianoluzi]

@@Painless360 the initial problem was that the drone was falling down without reason eve if it was close to the radio transmitter . So I tried to change the tango 2 at 250 mhz but the receiver become solid red. Now I fixed using the bind button following a procedure I found in a forum . I fear that the problem persist and the drone fall down again without reason. When I does is works again simply arming it again

[@olyddiego8515]

question tbs nano rx has a adaptor board haw can i use it properly install and its functions?

[@Painless360]

All covered in the Arduplane/Matek/AR wing build in the playlist... Happy flying

[@olyddiego8515]

tanks

[@MCsCreations]

Awesome work, man. 😊 I've just watched the first video of the Crossfire series when I saw this one. 😊

[@evgenzachem2739]

Hello !prompt please here at me on Crossfire GPS data from the menu of Taranis does not appear I choose detection of new sensors it about nine finds but among them there is no GPS data. but also for some reason telemetry in lua script inav on the remote also does not go though 3D fixation eventually occurs but for some reason the data from the controller flight most likely do not reach the remote in General I do not know what the problem is. you can tell on Crossfire behind on the remote control should be the last menu item displayed GPS data here I do not have them. in the configuration settings of the flight controller, inav has checked the data telemetry feed.What can be done .Where to find the answer that can suggest the ?!prior to that, the lua Script was working fine through the port F which was flying Nicky. Thanks in advance !

[@dingr]

My Micro TX was locked to FCC mode (i.e. not Open). I updated the Micro TX and Nano RX to 2.24 and they would not bind to each other. I updated to 2.25b and all was well. The Nano RX is lighter than the Immortal T antenna!

[@Painless360]

Yep, that was the bug in 2.24.. Glad you got it sorted!

[@fpvnafret]

I have the 2W model, and its in open region. I have problems with the nano rx, since is givingme very low range and it disconects. it wont bind in 915 mhz just in 800mhz.... help

[@Painless360]

What troubleshooting have you already tried?

[@chriscottell6854]

Hi, ive just bought the Iflight Chimera 7inch with Tbs from banggood. I have the Jumper T18 Pro aswell. I'm new to fpv and want to know what else do I need to get going, as most of the videos on youtube are 2-3 years old, need would like to get upto date gear.

[@Painless360]

See my Kit picks 2020 video for my choices.. Happy flying

[@hillbillypetej]

Hi IV done a DX9 mod for crossfire bind ok both had green light on nano and tx turn off and turn on again all working but no green light on crossfire is this normally or do I have a problem

[@Painless360]

Check the manual but I think you only have a green LED when it's bound to a receiver and connected..

[@ChristKrew-Rev1.8]

Can you point me in the right direction on using this with a fixed wing 4ch foam park flyer?

[@Painless360]

You could use a TBS Crossfire Nano Receiver Adapter that would give you regular servo connections.. Happy flying!

[@Sir_Brennan]

Thank you so much for this! I too had the 2.24 binding bug. Flashing 2.25 Beta sorted everything out perfectly.

[@DroneAcharya9]

Can I use nano for running a 4 channel rc plane?

[@Painless360]

Yes. See my Matek / Arduplane build..

[@Martin1519]

Can the SDA and SLC pads on the nano RX be utilized to Run the Magnometer/Barometer on a Compass GPS?

[@MikeRM399]

DO YOU KNOW IF THIS SET UP CAN BE DONE WITH THE FLYSKY RC ? Thanks

[@Painless360]

Not that I am aware of. Happy flying

[@6.5creedmoorrips6creedmoor2]

Hi I have a question nano tx updated to 288 nd after that when u go in to crossfire lua scripts nano RX says device killed 101

[@Painless360]

I've never seen a 'Device Killed 101' error..

[@serval_fpv]

Howdi so after sticking a nano rx on a new build and installing fw to a beta version a previous older quad using a v2 micro rx won't bind.. Question - do you know if they can use similar fw or you cant use a nano & micro ? Thanks in advance..

[@Painless360]

Sounds like a firmware update is needed on that one that won’t bind.. best of luck!

[@serval_fpv]

Painless360 you're up early hehe.. well if i got 2 different versions of the rx and 1 module i was hoping they can use the same fw ive asked days ago on fpvlab in the TBS section but no replys :/

[@robsmith6497]

I am using a nano on a futaba 16sz, where do you set the output mapping like you have done in the taranis.

[@Painless360]

Sorry, no idea. I don't have any Futaba radios.

[@ghettotech9617]

What if you got tbs micro modules

[@Painless360]

If you are talking about the TBS Crossfire Micro TX then it's the same process... Use the LUA script for the setup steps..

[@ghettotech9617]

Painless360 thanks

[@NightTrainFPV]

I just got my first crossfire and have a qx7. I heard you need the upgrade for qx7..but heard also that it is really for the latencies..what is your opinion on this. I have watched you since I started a year and a half ago and trust your honest opinion

[@Painless360]

All covered in my TBS Crossfire series.. a HW mod is needed for full CRSF speed as Frsky has made some odd decisions to ham-string their radios after the X9D..

[@flightready1587]

Great series of videos -- I recently integrated the TBS Crossfire setup per Method 1 outlined in the DX9 Crossfire Protocol Instructions (SPMR9910_Crossfire_Instruction document). Everything works great and I was wondering is there any way to get telemetry data on Spekrum transmitter screen (primarily voltage and RSSI). Thanks!

[@Painless360]

I've not tried it with a Spektrum radio, best of luck!

[@cenabitednbfpv587]

@@Painless360 you get it on screen with osd no need for radio but with hier end builds yes

[@JackpotJoe]

Is there a better receiver for a fixed wing aircraft that Im not concerned about weight?

[@Painless360]

If you are using a flight control or stabiliser then the Nano Diversity is excellent. If you are running the fixed-wing without then the TBS Crossfire 8CH Long Range Diversity Rx is excellent and has battery backup too!

[@rickvestuto]

I have the TBS Tango (Awesome radio) and the Micro TX......... took about 2 min to update firmware and then 30 sec to bind the RX Now to set it up in iNAV

[@Vaughnboilore]

I hope you did the qx7 mod to run the crossfire! To run 400000 baud rate otherwise that qx7 won’t run crossfire correctly and things will go bad and people can get hurt😬

[@Painless360]

I seem to be very lucky and have one of the very original units that seem to have the full speed inverter. I have bought the little adaptor from TBS in case I get another one.

[@ronchampagne8484]

cannot trim channels . Elevators lock in one direction and can't be trimmed back . I'm using with a simple stabilizer to avoid the complexities of flight controllers . Just another mess

[@Painless360]

I'd start by looking at the stabiliser setup. I've got a few videos on different ones on the channel and they all have slightly different setups. Best of luck

[@sleepingbearffg5008]

💪💪👊👊

[@rickduncan2929]

All this information EXCEPT the pinout. Lolz However you do a great job regardless

[@Painless360]

Please watch the rest of the series, The pinouts on the receiver are actually set by the transmitter. You can configure them to do all kinds of things. Best of luck!

[@Data04728]

I'm not happy with Crossfire microTX and NanoRX at all. The range is no more than a few meters. Support is not helpful, they just asked the questions I already answered. I hope I get my money back.

[@Painless360]

I cover the common mistakes in the TBS Crossfire videos, check them out. Hope it helps..

[@Data04728]

I did check many video ... to check what is wrong. Setup, freq, how to mount ect..pp. Your videos are very helpfull. But my product is not working and no really support from TBS. Check my video, just 7meter lost telemetry. -> kzbin.info/www/bejne/onWzeIWHmtJ4ocU