You folks have the BEST log splitter tutorials....PERIOD!
@johnsellers96233 ай бұрын
I like how your work table is perfectly level. I thought immediately that you were going to set the ball bearing onto the piece it sits on to keep it from rolling away. But you fooled me instantly. 👍
@pedrobarrionuevo16852 ай бұрын
Your information is stunning, thanks mate!.
@scottvincent7666 Жыл бұрын
Thumbs up for helping joe Erb!
@donaldandy9632 Жыл бұрын
Thanks for the explanation, Iam getting it and want to try it.
@justinvanberkom2960Күн бұрын
Thankyou
@justintanner70202 ай бұрын
So I had changed my fluid, afterwards it’s doin as you displayed it will not split the log.Any thoughts or ideas that I can try to do to fix?
@LarryHartley-vq2de9 ай бұрын
Good day, very informative videos. I replaced my log splitter valve and the detent wont pop back to neutral no matter how I adjust the detent. What do you think it could be?
@johnr5545 Жыл бұрын
Thanks god bless
@Zeeg195710 ай бұрын
I need help with my log splitter. The piston extends but as soon as it touches the log it retracts.
@RobertoRodriguez-ie9dl Жыл бұрын
My log splitter is a slow when the cylinder is engaged. Any ideas what it might be?
@amerikanstafford Жыл бұрын
I have the same question.
@josepherb76332 жыл бұрын
My log splitter is spitting out fluid when I try splitting and when I pull handle back any ideas
@RuggedMade2 жыл бұрын
Please email support@ruggedmade.com or call (855)-878-4433 and someone can assist you with this.
@josepherb76332 жыл бұрын
I’m having problem with my splitter, it has a breather cap where you fill it up. When you start it up and move handle in or out it starts spewing out fluid either way you go. It has no splitting power at all, just had cylinder repaired. Any ideas guys I can’t afford a new one.
@RuggedMade2 жыл бұрын
Please email support@ruggedmade.com or call (855)-878-4433 and someone can assist you with this.
@JohnMcNerney8 ай бұрын
Where is a good place to install the pressure gauge when adjusting the relief?
@RuggedMade8 ай бұрын
As seen in the video, the ideal place to install a gauge for the purpose of reading your valve's relief pressure is between the pump and the valve.
@stevebillow395 Жыл бұрын
Where can I get a cylinder like that
@RuggedMade Жыл бұрын
ruggedmade.com/
@dilepecollinsmaleka2210 Жыл бұрын
thats useful
@chrisyerp17411 ай бұрын
Vary helpful
@kingsleycollins6730 Жыл бұрын
Won't there be possibility of the valve moving while tightening the Valve Cap?
@RuggedMade Жыл бұрын
No Kingsley, there is enough friction holding the threaded adjustment bolt that it does not spin merely by installing the hex cap. You need an allen wrench to turn it.
@kingsleycollins6730 Жыл бұрын
@@RuggedMade Thanks a lot for this. I look forward to the day I'll built mine.
@toady..9833 Жыл бұрын
can you make a vid on pump adjustment?
@RuggedMade Жыл бұрын
The pump is not meant to be adjusted in the field, they are factory set.
@RuggedMade Жыл бұрын
We may do a video on pumps in the future that is more in depth.