DIY PCBs At Home (Single Sided Presensitized)

  Рет қаралды 1,322,474

TechBuilder

TechBuilder

Күн бұрын

Пікірлер
@TechBuilder
@TechBuilder 4 жыл бұрын
Please wear latex gloves and wear protective goggles when dealing with these chemicals. For this video, I ran out of gloves at the moment due to the massive shortage of medical supplies due to the COVID19 pandemic. Lye (developing solution) can be corrosive to human tissue, for this project, the concentration of lye is quite low. I washed my hands thoroughly after getting exposed to it. Ferric Chloride on the other hand barely has an effect to human skin, but it does leave a stain on everything when not immediately rinsed with water. Stay safe fam!
@Workshop111.
@Workshop111. 4 жыл бұрын
The number of views would be more if the video were translated into Arabic
@Workshop111.
@Workshop111. 4 жыл бұрын
The number of views would be more if the video were translated into Arabic
@mubasshirshah7871
@mubasshirshah7871 4 жыл бұрын
kzbin.info/www/bejne/fGrJpWuaarljf9U
@Sterlinxvii
@Sterlinxvii 4 жыл бұрын
Thanks for your
@johanneshass1614
@johanneshass1614 4 жыл бұрын
Just a very important FYI: Do NOT pour down the sodium hydroxide solution down the drain. It now contains copper(II)-hydroxide (or rather a hydroxy-complex, that's why it's blue!) and that is not very good for the environment. You actually have to bring that to a hazardous waste disposal facility. Yes, really. Your local wastewater treatment plant will thank you for not making them deal with heavy metals. Also, please store acetone in a very well ventilated area (preferrably outside!). Acetone has a very low flammability and high vapour pressure - if you're really unlucky you'll blow yourself up. Not a joke.
@new-knowledge8040
@new-knowledge8040 4 жыл бұрын
Brings back memories. Back in 1985, we technicians were making our own boards for all sorts of stuff. One of my pet projects was making a PAY TV decoder. I designed it so that it decoded the video line by line rather than the standard frame by frame method. Thus there was no need for a PLL ( phase-locked loop) circuit. It was powered by 12 vdc, and it only pulled about 12 mA, and the board was only 1.5 inch by 4.5 inch. So you just installed it inside your TV converter by tapping the converter's 12 vdc power line, and then cut the video connection that connected the RF demodulator to the RF modulator, and then feed these wires to the tiny decoder board. And that was it. You now had a PAY TV decoder. It decoded all the PAY channels, and did so instantly, since there was no PLL delay. Meanwhile, the engineers used the standard method that required tons of IC's and other components, and it therefore pulled plenty of current, so it needed its own power supply, and of course it needed its own box as well. That costs money. Mine, only had three IC's, MC4013, MC14538, and an LM393, plus a few transistors, diodes, etc. So making just one, cost about $5.00 total. Those days were fun indeed.
@426F6F
@426F6F Жыл бұрын
How do you learn about all of that stuff? Can you still use a similar workaround today for paid channels? That sounds so neat!
@temmie5085
@temmie5085 Жыл бұрын
@@426F6F No
@metamud8686
@metamud8686 Жыл бұрын
relevance?
@albertorojas472
@albertorojas472 Жыл бұрын
That's so nice! I would have liked to live in that time, a simpler time where technology was less integrated into society and solutions were more practical and simple. There is no way in which something like this works today, technological innovation has been displaced and relegated to mega-corporations with funds of millions of dollars to allocate to research.
@cessposter
@cessposter Жыл бұрын
​@@426F6F modern tv is digital and uses encryption similar to what the internet uses
@StephenNesbit
@StephenNesbit 4 жыл бұрын
That was, hands down, one of the nicest and easiest to follow KZbin tutorials I've seen in ages! Thank you for that! :) So many content creators mumble or talk waaaaaay to fast without taking the time to speak CLEARLY.
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks man! Means a lot! I wanted to make a tutorial on PCBs for years but I found out a lot of people already posted it. I revisited some of the classic tutorials only to realize they weren't first-timer friendly, so I made this vid anyway hahaha 😊
@MoonlightEmbrace
@MoonlightEmbrace 4 жыл бұрын
Honestly, before I saw your tutorial I always imagined making your own PCBs was a way more complicated and chemically hazardous process. Glad to see it's actually way easier than I thought!
@ezion67
@ezion67 4 жыл бұрын
Overall a good tutorial. Just 3 remarks. 1) There is a easier/better way to cut PCB material that also works with glass-fiber and double sided material. Score BOTH sides 2 to 4 times with the sharp side of your blade, then snap. 2) Temperature is important for development and etching. Do both "au bain marie" in a tub of hot water, to get around 30C - 40C. You may find you get better results and the chemicals can literally last years. Years? yes. My etching machine holds about 2 liters Ferric Chloride. The same Ferric Chloride has been in there for over 10 years and was used to etch almost 2 square meters worth of double sided PCB material. I add Hydrochloric acid to compensate for evaporation and keep the solution active, even though there is now a lot of copper in there. 3) Please be safe, pure Ferric Chloride only stains HOWEVER the Copper Ferric Chloride mixture you get after etching is rather poisonous.
@tanvach
@tanvach 4 жыл бұрын
One tip is to leave as much copper on the board as possible, and only etch the spaces between the traces. Usually there is an option in the PCB software like "create ground plane". First, this reduces the amount of etching required significantly, extending the life of your solution. Second, you will have more uniform etching, since there are no areas that get exposed to bare etchant for a long time. Third, you'll have a ground plane to help reduce interference and make your trace impedance more consistent (important for high frequency or timing sensitive applications).
@ThIncapable
@ThIncapable Жыл бұрын
So etching is just an engravement on the copper board?
@cryingbagel
@cryingbagel Жыл бұрын
"Only peel the PCB in a dim room." Proceeds to peel the PCB in a room brighter than the beaches of Normandy.
@flat-earther
@flat-earther Жыл бұрын
yeah BTW ev8, have you become a flat earther yet?
@larrybud
@larrybud 10 ай бұрын
I mean, he's filming.
@MaxC_1
@MaxC_1 9 ай бұрын
Doesn't matter as long as all light is artificial from LEDs, they have zero UV output and the film is sensitive only to UV, so even dimmer sun will start reaction while several thousand lumens of LEDs won't
@ArdLight
@ArdLight 9 ай бұрын
​@@flat-earther🌍🌎🌏🌐
@CommenterRick
@CommenterRick 3 жыл бұрын
You explained everything in a simple, straightforward and slow pace that made it EXTREMELY understandable. I hope you become a teacher because you have a great skill at presenting information. I also admire your ingenuity at building the machines you needed to finish the project. Well done!
@KrotowX
@KrotowX 2 жыл бұрын
Definitely brings back memories from 1980-ies. When I made my DIY PCBs only in such way because there were no better ways.
@dzidzac
@dzidzac 2 жыл бұрын
TechBuilder , you have just gotten me out of the months-long toner-transfer vicious circle - in 10 minutes and 10 seconds! Thank you greatly for that!! Every day is a new lesson!
@hrishikeshb
@hrishikeshb 3 жыл бұрын
This is my preferred method of building PCBs too. I use transparent sticker paper instead of the paper and oil. It’s too messy :) The transparent sheets are think and stick to the PCB thereby reducing the gap between the film and the PCB. The lines are more defined with this and I was able to get clearances as low as 0.3mm and track widths of 0.25mm with this.
@jacobnoble2167
@jacobnoble2167 11 ай бұрын
Any sticky paper?, and im gussing you print your schmatic to the paper and then just slap it on and the do the rest of the steps?
@hrishikeshb
@hrishikeshb 11 ай бұрын
@@jacobnoble2167 not an opaque paper sheet. I print them on a transparent sheet that can be printed on an inkjet printer, but with one sticky side. They are clear transparent plastic sheets that can be printed on.
@jacobnoble2167
@jacobnoble2167 11 ай бұрын
@@hrishikeshb Could you link what your talking about and im guessing you print on the non sticky side? THen Uv expose... etc
@hvm2hvm
@hvm2hvm 8 ай бұрын
I kinda knew the process before but this made it so much clearer. It was super easy to follow and had all the information needed but none of the fluff. Thanks dude!
@notsonominal
@notsonominal 4 жыл бұрын
Now thats an interesting approach, by some miracle a local store is selling positive presensitized boards, will have to try this. two thumbs up!
@brandonstevens6886
@brandonstevens6886 4 жыл бұрын
I wish I had a store like that
@booruvcheek1331
@booruvcheek1331 4 жыл бұрын
You have a local store selling electronic components.. I envy you.
@brandonstevens6886
@brandonstevens6886 4 жыл бұрын
@@booruvcheek1331 You would be surprised. But they are slowly dying
@AgabaMed
@AgabaMed 2 ай бұрын
Thank you but I would wish know how to use prototype software
@fomxgorl
@fomxgorl 2 ай бұрын
i didn't even know they existed. hope there's one near me
@simhoper8953
@simhoper8953 4 жыл бұрын
Man... you are an asset to the whole world! Hope you shine more and share your knowledge with te world! Thank you!
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks man!!!
@Arisentec
@Arisentec Жыл бұрын
Peat 1年前 I usually don't comment on videos, but this is something else. Very clear& easy to follow. Definitely worth subscribing
@fractera
@fractera 4 жыл бұрын
How I wish this quality tutorial existed 7 years ago. Tough times.
@TechBuilder
@TechBuilder 4 жыл бұрын
I feel ya
@peat1
@peat1 3 жыл бұрын
I usually don't comment on videos, but this is something else. Very clear& easy to follow. Definitely worth subscribing
@Denkaa1987
@Denkaa1987 4 жыл бұрын
Thank you! This was very helpful. Did everything as suggested. Printed my designed circuit on A4 plain paper with laser printer. Did some testings to find the right recipe for my conditions and I found that paint on paper are tend to blur after contacting with cooking oil, so I used spray varnish to protect my paper circuit before applying cooking oil. This worked perfectly.
@cavemanjoe7972
@cavemanjoe7972 3 жыл бұрын
This method is meant to be used with an inkjet printer.
@markp8295
@markp8295 4 жыл бұрын
Amazing content. Clear and educational. Thank you.
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks! :D
@TheEulerID
@TheEulerID 2 жыл бұрын
Personally I recommend spraying the PCB with a solder-through lacquer, especially if it's not being used immediately. In the longer run, it helps prevent corrosion. Alternatively spray the track side (on single sided PCBs) after installing components and making sure any flux is cleaned off. I also score both sides of the board before snapping (and I use the sharp side of the blade). I've also been able to snap-break glass fibre boards that way. Also, I'd recommend using tungsten carbide bits for drilling PCBs as the standard hss types tend to blunt very quickly, especially with glass fibre.That can matter for accuracy when drills become dull.
@KE8UYV
@KE8UYV 2 жыл бұрын
Thank you for the tips. I'll be making my own pcb for a project in the next few weeks.
@TheEulerID
@TheEulerID 2 жыл бұрын
@@KE8UYV Good luck, as it can be very frustrating.
@kbejustervesenet7261
@kbejustervesenet7261 4 жыл бұрын
You should swap the paper with a Overhead Transparent sheet, then the PCB traces will not have all the inperfections that your resulting PCB has. (pixelation and small holes.) Print the pattern Mirrord, so the printed side is turned with the printed side against the Photo-resist dirrectly to reduce bluring of the edges of the traces.
@tinfore
@tinfore 4 жыл бұрын
For those without a laser printer, this video is priceless! Thanks!!!
@TechBuilder
@TechBuilder 4 жыл бұрын
Glad it helps!
@BradBo1140
@BradBo1140 3 жыл бұрын
Great video. I hardly know what a resister and a capacitor is but I’m gonna go out, buy a bunch of things, and make a circuit board. That was such a good tutorial,fascinating.
@favesongslist
@favesongslist 4 жыл бұрын
This brought back memories for me, I used to make a lot of prototypes this way.
@TechBuilder
@TechBuilder 4 жыл бұрын
Same! I brought back some memorable moments when we used to compete in robotics and fabricated circuits with this method. These days I only use it when I need a PCB done within the day since Chinese PCB fabrication services are becoming a lot cheaper by the day.
@favesongslist
@favesongslist 4 жыл бұрын
@@TechBuilder I used the black tape and transfers for small runs as they give clearly defined boards, you can also get Etch resistant transfers for one off prototypes
@GodzillaGoesGaga
@GodzillaGoesGaga 4 жыл бұрын
@Timothy, same as me. Used an old tanning lamp for the exposure light. So much easier to pay $2 to get a professional board done!!
@joefish6091
@joefish6091 3 жыл бұрын
@@favesongslistah the black tape and transfers, that dates some of us , fond and annoying memories.
@dougcox835
@dougcox835 4 жыл бұрын
Watching this I noticed countless things that would make the process better. But then I realized that you are showing the most basic and simple way. One thing that I have learned about cutting the PCB is that a good heavy duty pair of scissors does the job surprisingly well. You might be worried about ruining the scissors. If you are you can buy a cheap pair just for the job.Thicker PCB would be a challenge for scissors but the thin ones like you made are not a problem.
@konradwiniarski
@konradwiniarski 4 жыл бұрын
Very nice and straight forward instruction. I used this method around 20 years ago already ;-). One suggestion. Use laser printer instead. The lines will be much more accurate and edges sharper. You can also experiment with printings on a foil.
@joefish6091
@joefish6091 3 жыл бұрын
yes, a laser printer, we could go down to reliable 6 thou tracks with a laser printer. also 0805 SMDs. SOICs and so on.
@geraldwesley
@geraldwesley Жыл бұрын
just started electrical engineering and this got me super excited for it
@UB8JDA
@UB8JDA 4 жыл бұрын
Hello, I'm from Russia! Thank you for the video, 73!
@TechBuilder
@TechBuilder 4 жыл бұрын
Welcome! Greetings from the Philippines my good sir!
@ooltimu
@ooltimu Жыл бұрын
Ferric chloride etching can be significantly sped up (3-4 minutes) by heating the solution. I usually put it in a cooking glass container on the stove and heat it on the lowest setting, while agitating the solution and board with a stick. Toner transfer can yield same results and much cheaper. I made quite a few SMD boards with close traces (QFP32) and even one double sided board (even though I admit the alignment was tricky and got it on the second try).
@rubbermaiden
@rubbermaiden Жыл бұрын
Very nice, I did this in the 80's with regular pcb boards with decalcs and permanent markers. Now with this light transfer method make things lots easier.
@larrybud
@larrybud 10 ай бұрын
I recall doing photo resist in the 80s, but you had to draw the circuit by hand!
@cuznerdexter
@cuznerdexter Жыл бұрын
That was great to watch. Forgot how many steps are needed to produce a simple pcb. This video was an eye opener. Great work!
@Axel_Andersen
@Axel_Andersen 8 ай бұрын
Todays offer from JLCPCB 100x100 mm2 two sided with solder mask and silkscreen 5 pcs = $2 plus shipping .... DIY PCB does not really make sense anymore, too bad, I liked to do it.
@jasoncampbell8879
@jasoncampbell8879 4 жыл бұрын
Interesting to see you just use a paper printout. I've always printed to high temperature overhead transparencies. Your way of wetting it and sticking it to the board saves any unwanted movement.
@TechBuilder
@TechBuilder 4 жыл бұрын
Transparencies give the best results! I do find the inkjet and oil more economical. Yes! The oil really helps with the grip! :)
@svsv9
@svsv9 2 жыл бұрын
Your voice tend to make me think you're very young. Hope you inspire many guys around the glove. I like your techniques and very well documented video. The chemical in this country where I live cost me a lot, unfortunately. Nice job. Thank you keep it!
@victory5056
@victory5056 4 жыл бұрын
incredible, I loved the video. I can't wait to try this myself!
@TechBuilder
@TechBuilder 4 жыл бұрын
Have fun! Drop a comment here if you experience some difficulties in the process, I'd be happy to help.
@joefish6091
@joefish6091 3 жыл бұрын
double sided works well too, just tape the topside acrylic transparency to the underside by one edge, fit a double sided PCB inside and expose. remember to have the printed side closest to the copper, then theres less or no diffraction errors from the light box. use the pads to align both layers then tape. as long as tph pads are big enough to allow for slight misalignment, should be golden. we used this method for small scale commercial prototyping late 90s, the benefit is you can make a prototype PCB in hours. from CAD to construction. using a proper PCB production company takes a day or two, depending if theres a local one.
@larrybud
@larrybud 10 ай бұрын
Problem with DIY double sided are through hole plating. Try to get a 44 in PLCC socket to make contact with both sides. It's impossible. If you have simple discrete components you probably can get an iron on both sides, but not with many components.
@bummers
@bummers 4 жыл бұрын
When breaking the PCB, better to keep the scored line flush with the book and table surface.
@slowgaffle
@slowgaffle 4 жыл бұрын
Awesome tutorial! However I would suggest that people not think of lye as “a mild soap.” It becomes soap when it dissolves lipids and proteins. If it feels soapy guess where those lipids came from? Also keep the solution in HDPE plastic (number 2) or glass preferably, and never anything aluminum. You might not even notice that you’ve burned yourself with it for several hours.
@mr.gourmet430
@mr.gourmet430 4 жыл бұрын
Remember this in school, It was always fun.
@Rising_Pho3nix_23
@Rising_Pho3nix_23 Жыл бұрын
Very easy to follow. Simple instructions, practical approach. Quality audio and visual. Instructions and example and explanation. Overall excellent stuff thank you! This is how you know when someone knows what they're doing.
@RespawnRestricted
@RespawnRestricted 3 жыл бұрын
i 3d printed a mini dremel table saw its like 8in by8in perfect for cutting pcb board
@mattiaiezzi9381
@mattiaiezzi9381 2 жыл бұрын
Ok. I did try this. Took a few attempts but got it working. Here's my advice: I use a 4x8W UV lamps exposure unit at a distance of about 10 cm. It takes 10 minutes (anywhere between 8 and 12) to get proper exposure I oiled the paper separately, dried it off and then put it on the board. Way less messy to clean up later, it only takes some water and a drop of dish soap I used 6g of sodium hydroxide in half a liter (500mL) of water and it worked very well by leaving it in there a bit, agitating it with a brush. I think it got saturated though, as I needed to redo the solution midway. Maybe a liter would be the better choice I used a 1:1 ratio of ferric chloride and hot water to etch. This saves some time and cuts costs of etching I got very good results using 0.762mm traces, perfect definition this way. I think I could go down to 0.254mm if I wanted to, the results were that good Overall this was a great video to learn basics, I just needed to perfect my method
@glasslinger
@glasslinger 3 жыл бұрын
It is best to use an inkjet printer (HP is best I have found) with inkjet transparencies for the artwork. This will significantly improve your line edges. (Laser printers don't have the black density necessary for this process.) Also, a much higher power UV lamp lets you finish the exposure in less than a minute, which also helps reduce undercut. (I use a 400 watt mercury vapor street light with the outer envelope removed) With this procedure I regularly do 15 mil traces with no breaks and clean edges.
@nobodynoone2500
@nobodynoone2500 Жыл бұрын
A single point source of light also improves edges. Love your videos.
@evancourtney7746
@evancourtney7746 Жыл бұрын
2 Cool points for the guy who remembers the part number of the Radio Shack kit for these boards. Man I miss that store:(
@randommusings48
@randommusings48 4 жыл бұрын
YT recommended this video and I watched the whole thing.
@MrNoobed
@MrNoobed 4 жыл бұрын
Thank you. I had given up on it because I thought I had to do toner transfer. Doing it with inkjet is amazing
@TechBuilder
@TechBuilder 4 жыл бұрын
Same! Agree!
@GrandNebSmada
@GrandNebSmada 4 жыл бұрын
Ok so nobody gonna mention how he used his bare foot to hold that PCB down????????
@normanvename3724
@normanvename3724 3 жыл бұрын
This is the best PCB tutorial I've seen. Thank you!
@amitbharat77
@amitbharat77 4 жыл бұрын
You forget to apply layer of paint on the exposed copper layer. (Current + humid air + copper = copper oxide = failed circuit board)
@TechBuilder
@TechBuilder 4 жыл бұрын
Agree! I suggest others to do the same, but only after the soldering. Flux mask is also a nice option.
@nickli1564
@nickli1564 4 жыл бұрын
@@TechBuilder Would conformal coating work as well?
@glenford3436
@glenford3436 4 жыл бұрын
I've experienced, the copper clad of pcb would develop a green rust-like subtance on its surface
@xcruell
@xcruell 4 жыл бұрын
@@glenford3436 its oxidation, copper got really colourful oxidation
@dougcox835
@dougcox835 4 жыл бұрын
Simple solution is to tin the entire board before putting on the components. Also the solder will bridge the small pinholes in the traces. Any extra copper shorting traces would also be revealed as the solder will flow over that as well.
@captainpumpkinhead1512
@captainpumpkinhead1512 2 жыл бұрын
Holy crap!! This looks WAY cheaper than shipping JLC PCBs from China!! Thank you so much for this!!
@larrybud
@larrybud 10 ай бұрын
There are definitely pros and cons. I do DIY pcbs when I'm iterating through changes and making sure my circuit is right. In fact I just did one the other night and forgot to add power pins to one module in the schematic. I usually do breadboarding first, then make the schematic from the breadboard, depending on what I am doing. Doing the board DIY allowed me to find that problem immediately, as well as changing some button placements which went through the back of the case for user input/selection. Once I'm satisfied, however, I'll get professional boards done. It's still very cheap, and having a solder mask and tinned pads makes it way easier to solder, especially if you have small SMT Ics with pins which are closely spaced.
@carrycartoon
@carrycartoon 4 жыл бұрын
Hey bro waiting for your next video 😁♥️✌️🔥
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks!
@sastrydasigi7010
@sastrydasigi7010 8 ай бұрын
Excellent! Clear, detailed and well-paced explanation. Thank you very much.
@col8981
@col8981 4 жыл бұрын
Great video, I find that if you warm the Ferric Chloride in the microwave to about 50/60C before you use it it works a lot better
@TechBuilder
@TechBuilder 4 жыл бұрын
I'll try that. This man!
@雪鷹魚英語培訓的領航
@雪鷹魚英語培訓的領航 3 жыл бұрын
I love how organized your closet is.
@CliffordKintanar
@CliffordKintanar 3 жыл бұрын
Nice video. One correction though: sodium hydroxide is not the main ingredient of soap, but is used to make soap from fatty acids. It’s actually the main component of drain cleaner, or “liquid sosa”
@DrewMarold
@DrewMarold Жыл бұрын
Nice & straightforward. I would add a cautionary note about using acetone inside, you MUST have good ventilation. It evaporates so quickly you can build up a dangerous level of highly flammable fumes in short order.
@jackcrisabarnas4539
@jackcrisabarnas4539 Жыл бұрын
Nung nakita ko yung Summit. HAHAHA Pilipino to. Pati pala sa pagsasalita. By the way ganda ng content!! ❤️❤️❤️
@TENCUHTLI
@TENCUHTLI 4 жыл бұрын
What a relaxing way to learn something
@mikkocaguiat9830
@mikkocaguiat9830 3 жыл бұрын
Got nostalgic when I saw your Sadiku Book. Brings back college memories. 😅🙌
@whatamievendoing
@whatamievendoing 4 жыл бұрын
Can't wait for your video on the electric car circuit. Exactly the kind of thing I've been wanting a clear and concise explanation of.
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks man! Almost done filming it! It may take a few more months, due to my video edit lineup.
@tubegor
@tubegor 4 жыл бұрын
Wow the real tech builder and your workshop looks amazing. Thanks for sharing.
@spider_corsa
@spider_corsa Жыл бұрын
For step 8: the drilling will be more precise if you're preparing it with eg a pricker or something and the drill will not slide to an improper position on the board.
@srijantanwar3245
@srijantanwar3245 4 жыл бұрын
One of the best guide I ever saw
@mohamedfaroukel-alem7253
@mohamedfaroukel-alem7253 4 жыл бұрын
Your explanation is so clear and simple yet you covered the topic very well!
@TechBuilder
@TechBuilder 4 жыл бұрын
Thank you!
@RPBCACUEAIIBH
@RPBCACUEAIIBH 4 жыл бұрын
I managed to make .008 inch (0.2032mm) traces pretty reliably with similar technique, except I sprayed Positive 20 photoresist on polished FR4 PCB, using inkjet printer with the color cartridge filled with all black ink, set to high resolution photo and and photo paper settings, but I actually used normal paper instead of photo paper. :D That was achieved with my old HP Deskjet F2480 printer, and regular 80g/m2 paper, and cooking oil to make it transparent, as you mentioned. Now I bought a new pigment based (HP Deskjet Ink Advantage 3775) inkjet printer, and high quality 90g/m2 Xerox Colotech+ paper, which has smooth surface, and it actually gets more transparent when the oil is applied. I bet it's gonna be even more reliable once I perfect the method, although the old printer really soaked the paper with ink making it really black, this new one, does not even at high resolution photo settings although it looks even blacker then with the old printer, it's kinda transparent black(which is not good)... I'm thinking if I can't make it work with the new pigment ink, I'm gonna experiment with mixing pigment based, and dye based ink to get the blackness I need to achieve even though it may ruin the cartridge.
@hlarks
@hlarks Жыл бұрын
I took electronics in HS in the 80s and we had the machines to make boards like this. I still have four of those projects.
@JamieBainbridge
@JamieBainbridge Жыл бұрын
Would the 12 minute exposure box be more efficient if you put mirrors on the walls and floor, and added a door with the same?
@chronobot2001
@chronobot2001 Жыл бұрын
I use vinegar and salt to remove the copper. It works best over low heat while agitating. I have done this with the toner transfer method. I assume it would work with this also. Great video. It looks far superior to the toner method.
@JMacalinao
@JMacalinao 4 жыл бұрын
Man, the nostalgia of producing PCBs for school projects... (106 represent, hehe)
@TechBuilder
@TechBuilder 4 жыл бұрын
115 here! Hahaha. Must have brought back so much memories hehehe.
@DanialADHOfficial
@DanialADHOfficial Жыл бұрын
Thanks making this video simple.. most easiest video for my brain to process the step by step information
@anon5582
@anon5582 Жыл бұрын
That was really informative and comfy to watch. Sad that you stopped uploading videos to this channel
@yamlcase230
@yamlcase230 6 ай бұрын
You think I could use a leftover Whitestone dome UV light?
@dahlavibez5726
@dahlavibez5726 2 жыл бұрын
Wow very beautiful result at the end I'll save this
@laszlovona
@laszlovona 4 жыл бұрын
to be frank, nowadays almost all hobbyists go for breadboard, use several meters of flimsy patch cables, and then the 'built' contraption finally looks like a bush and not an electronic project.. and the worst part is when they let this temporary protototype be the final solution... aww . 😟😭 I have seen breadboard implementations built into frames, enclosures as final... it hurts... so it is really good to see that you created this thorough educational video on how it is PROPERLY done! 👍
@TechBuilder
@TechBuilder 4 жыл бұрын
Thank you! Hahahaha I feel ya! I eventually made an unhealthy habbit of using fabricated PCBs even for the simplest circuits. 😂 It makes the project more satisfying to the eye hahaha
@hopelessnerd6677
@hopelessnerd6677 3 жыл бұрын
Awesome video. I built a UV exposure unit into an old scanner body with 3W UV LED's. It took my exposure time from 2-3 minutes to 12 seconds with perfect results.
@JarosawSwierczewski
@JarosawSwierczewski 4 жыл бұрын
One of few people who can solder correctly.
@johnphillip6328
@johnphillip6328 4 жыл бұрын
1 percent I would say 😁
@matusondrus8987
@matusondrus8987 4 жыл бұрын
Good video, many people dont know this method. But i have one suggestion. If you want better resulst aspecially with thin traces try to use transparent foil for inject printer. I use this methode for several years and results are much better than plain paper. If you use transparent foil you need to reduce UV expositure time. In my case max 2 minutes will work. I use nail polis UV light.
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks! I agree! Although it might be scarce in times like these, the transparency film does a better job indeed! Just ordered a roll of those dry film foils, I'll try that! Thanks for this! 😊
@boots7859
@boots7859 3 жыл бұрын
Great video as always. And, presentation is slow, calming and comes across as do-able by the watcher without previous experience. Perfect for tutorials, and excellent, interesting projects.
@emmettturner9452
@emmettturner9452 4 жыл бұрын
How about using laser printer with overhead transparency sheets (not toner transfer)?
@PLPawkoW
@PLPawkoW 4 жыл бұрын
It will also work, I'd say even better than toner transfer. Also, you don't need a special photosensitive laminate, you can buy photosensitive paint in spray cans. Make sure your transparent film won't move, cure it in UV light, develop then etch the board, either using ferric chloride or, in my opinion, a better option, sodium persulfate.
@TechBuilder
@TechBuilder 4 жыл бұрын
I agree!
@saveplanet3977
@saveplanet3977 4 жыл бұрын
Really a clean and good demonstration on how to make PCBs. You have simplified it.
@morthim
@morthim 4 жыл бұрын
this is the best video i've seen related to this yet. i hope it spreads
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks!!
@TheAstronomyDude
@TheAstronomyDude 4 жыл бұрын
Super cool video! I didn't know that type of DIY pcb existed.
@mubasshirshah7871
@mubasshirshah7871 4 жыл бұрын
kzbin.info/www/bejne/fGrJpWuaarljf9U
@Evilslayer73
@Evilslayer73 2 жыл бұрын
Very well described tutorial you are a master at explaining clearly and very precisely what to do !! awesome! Can we use vinegar as etchant?
@KE8UYV
@KE8UYV 2 жыл бұрын
Thank you. You have done a fine job of explaining this process.
@MichaelShor
@MichaelShor 3 жыл бұрын
As I understand it, lye is not an -ingredient- in soap, but a processing chemical to separate the glycerin from oils. It is highly caustic, not like mild soap at all. Basically, it's the common ingredient in drain cleaner, and, if left on your skin, it will literally melt it.
@weldandcutdotcom
@weldandcutdotcom 4 жыл бұрын
Very well done. I have been considering other methods of making PCBs with a laser printer but I have not thought of using plain paper and baby oil. Thanks
@TechBuilder
@TechBuilder 4 жыл бұрын
Welcome! :)
@amlek2002
@amlek2002 Ай бұрын
3:48 If I understand correctly, P Diddy would be an excellent PCB maker.
@naunruizperez9614
@naunruizperez9614 4 жыл бұрын
That was hands and foot down . Verry helpful video thanks.
@_Giorgio_
@_Giorgio_ Жыл бұрын
My dad whose main hoby is electronics (he built his own radio at about 20 yo) still uses this method and so do I for some of my projects
@prozacgodretro
@prozacgodretro 4 жыл бұрын
Wait, what if you used a resin based 3d printer, that uses uv backlight.. and put your pattern on the lcd.... ? Best case scenario you just upload your PCB design into your machine turn it on for an hour and it works, worst case scenario the Fidelity of the exposure gives you individual pixels on your board... I'm kind of leaning towards the latter but still be interesting to try
@zaidhussain5206
@zaidhussain5206 4 жыл бұрын
Thank you for sharing this video, the copper traces will start to oxidize after a while, one thing to prevent that is to add a protection layer , a tinning process can fix this issue , can you please explain some affordable tinning process ?
@TechBuilder
@TechBuilder 4 жыл бұрын
From where I came from, peeps made a norm to coat boards with liquid flux intended for SMT reflow. It's cheap here and smells like petrol. Once the liquid dries, the flux contents solidifies and crystalizes covering a clear coat of the traces, it also helps a lot in soldering too! I also tried spraying clear enamel spray paint as an anti oxidation after I do the soldering, it helps in making your circuits become water resistant, depending on how thick the spray layer is.
@zaidhussain5206
@zaidhussain5206 4 жыл бұрын
Thank you for your update , I will try both ways .
@jessstuart7495
@jessstuart7495 Жыл бұрын
Fiberglass (FR-4) PCBs can absolutely be scored and snapped. The fibers on the edge can be sanded or filed down. I prefer this method, as it produces less fiberglass dust than sawing the PCB.
@shubhamsawant5129
@shubhamsawant5129 Жыл бұрын
Well thanks for the video and the hint that we can also use normal white light, I totally had forgot this 😅
@jia683
@jia683 Ай бұрын
this video was very relaxing to watch!
@AnilArya51
@AnilArya51 3 жыл бұрын
Came here back going to make PCB, last time I messed thing up I hope this time I succeed. I am using the other etching solution not Fecl3
@ervinbarron5372
@ervinbarron5372 Жыл бұрын
What software do you use to design your pcb’s and print them? Thanks! Can you use regular etching solution for the photo positive boards?
@bhushanrane13
@bhushanrane13 4 жыл бұрын
Thanks for the guidance video. I like the PCB etching machine that you made to shake the PCBs in Ferric Chloride. Can you please share how you made that machine?
@TechBuilder
@TechBuilder 4 жыл бұрын
Thanks! I have just uploaded a video on how to make a DIY PCB Shaker (rocker). You can check it out!
@joefish6091
@joefish6091 3 жыл бұрын
@@TechBuilder back in the late 90s at work, we used a vertical tank with air bubbles. fish tank type system.
@MrBobWareham
@MrBobWareham 4 жыл бұрын
Don't forget to print backwards so the ink side is touching the board you will get a better transfer I used to do all this about ten years ago and it's ok but I used to use clear film in my laser printer much better
@jm_sc
@jm_sc 8 ай бұрын
Been following you since you dropped that BB8 diy video, that really catch me on arduino but was too young to understand a lot of that stuff at the time. Now I'm ready
@NorthernKitty
@NorthernKitty 4 жыл бұрын
Great job!! Yours is the first DIY PCB video I've watched where I feel like, "yeah, I can do that." 😋
@spehropefhany
@spehropefhany 4 жыл бұрын
If you have any steel nearby, ferric chloride vapor (especially if you warm it to speed up the etching) will rust everything. Best to do it away from any lathes, milling machines etc.
@thorhammer6040
@thorhammer6040 11 ай бұрын
3:45 - Would red light be better not to expose the board?
DIY PCB Fabrication (Dry Film Inkjet Method)
5:35
TechBuilder
Рет қаралды 452 М.
Make your own PCB with a sharpie!
32:59
backofficeshow
Рет қаралды 35 М.
Enceinte et en Bazard: Les Chroniques du Nettoyage ! 🚽✨
00:21
Two More French
Рет қаралды 42 МЛН
Beat Ronaldo, Win $1,000,000
22:45
MrBeast
Рет қаралды 158 МЛН
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН
UFC 310 : Рахмонов VS Мачадо Гэрри
05:00
Setanta Sports UFC
Рет қаралды 1,2 МЛН
How this tiny PCB Motor Survived 1.6 BILLION SPINS
12:33
Carl Bugeja
Рет қаралды 401 М.
DIY High Speed 3D Printer (CoreXY From Scratch)
29:24
TechBuilder
Рет қаралды 532 М.
Can You Charge A Phone with Marbles?
18:06
Engineezy
Рет қаралды 1,4 МЛН
How PCB is Made in China - PCBWay - Factory Tour
13:12
DD ElectroTech
Рет қаралды 4,7 МЛН
Custom Transformer Shatters All Voltage Records (ft. 3D Printing Nerd)
21:23
Building a Massive LEGO Tank
17:56
Brick Technology
Рет қаралды 314 М.
The fastest way to make crisp PCBs at home!
10:56
Made with Layers (Thomas Sanladerer)
Рет қаралды 914 М.
Enceinte et en Bazard: Les Chroniques du Nettoyage ! 🚽✨
00:21
Two More French
Рет қаралды 42 МЛН