Program Any ESP Modules EASILY with this | ESP32 & ESP8266 Programming Jigs

[@MakerAventuras]

I've been using them for months, and they are awesome, a VERY good tool to have. Everyone using esp's should have one.

[@techiesms]

100%

[@hachogonzalez8649]

You rock - this jig is so nice!

[@techiesms]

Thanks ✌️

[@varunkumarr9633]

Thanks alot bro, i have been searching for this for so many days, and I just ordered ❤

[@techiesms]

Happy Making 😇

[@rlrentertainmentsinventions]

Great one Bro 👍

[@techiesms]

Thanks ✌️

[@Eng-Nabeel2004]

This is very useful tools for programmer's, Thanks for these knowledge full videos👍👍👍👍

[@techiesms]

😇

[@HarbansSingh-ce2tm]

Good programmers information video bro...❤

[@techiesms]

Thank you so much 😀

[@smartteg7381]

Please do video on KME smart

[@TYGAMatt]

I have the esp32 version. It's very useful

[@techiesms]

Yes it is. Even the ESP8266 is also very useful

[@harvinjoy9895]

What do you do with the enable pic after you power the module standalone ?

[@kaloprojects]

Cool :) never seen those nice 'snap' sockets for the Esp-12E/F.. module. Dummy question: How to insert the finally programmed esp module to my pcb ? What i mean is: i do not want to solder the coded chip directly into my pcb .. because i need to take off again on any sketch code updates, right ? any recommendation how other folks insert the coded chips into their pcb .. any nice 'snapping sockets' you recommend (i mean professional small industry sockets, not any huge 3d prototypes)? .. or how do you upload code to esp-12F when soldered on target pcb already ?

[@kaloprojects]

does anybody have an idea ? Are you all soldering flashed module into your pcb ? if yes: how can you flash any updates later on ?

[@klopez0017]

​@kaloprojects Expose the TX, RX and GND pads for programming. This way, when the esp is soldered, it can still be reprogrammed.

[@Faizan-r1h]

@@klopez0017 and gpio 0 pin too.

[@uskcodeverse]

I've an issue of connectivity ,I'm working with ESP32 Wroom 32D module when I'm adding a device to esp rainmaker app it is stopping at step 1 send wifi credentials giving error like failed to associate device , I've followed many suggestions in guthub and internet but not working I've tried by changing versions of board managers but didn't work . Could you provide solution?? I've follwed one of your video on common errors in esp rainmaker app but my issue wasn't listed in it.

[@ismzaxxon]

Drivers. google arduino driver problems. Lots of information. Basically, windows 11 keeps trying to force new drivers onto us, yet most of our systems only work with the old drivers.

[@401uwu7]

can i program a esp32 chip using the esp 8266 node mcu..you have done the same thing using another esp32 but i have only esp8266 ..is it possible?

[@techiesms]

Yes you can program it

[@crazycoolguy109677]

can esp01 gpios be used in jig just like esp8266?

[@ismzaxxon]

These are awesome. I wished there was a version where i could override my wemos mini for programming. Windows 11 drivers don't work. After googling the issue it seems only the old drivers work. I have been using your programmer for years. People.. be gentle and don't for it.

[@TechnoSAP]

👍

[@pcmobiletechnicalsolutions8504]

i already made this All in one universal programmer can programme Atmega Esp all in one programmer

[@YaranaIotGuru]

Can we use esp8266 and esp32 at the same time 😮

[@techiesms]

No, both are programmed in different programming jigs

[@digitalrain5800]

cool

[@NeilMehta-p6t]

Make a video on raspberry pi 5

[@a1motivation81]

इसी विडियो में इसका हिंदी ऑडियो भी अपलोड कर दीजिए

[@galdakaMusic]

If you insert tynyLLAma inside ESP32 and make working for Home Assitant you would be rich

[@mayankpatel97]

By searching names of WiFi access points such as Raipur bhjia house and pushpam jewellers on the Google map . People can find your location. It would be better if you hide them in future

[@techiesms]

My location is already public so it’s ok

[@shubhamadtp]

​@@techiesms Watch his gps without gps.