The Ultimate RF Remote Control Switch Review: Functions and problem solving

[@greenmoss]

Excellent video. Thank you for helping us all out.

[@ShowAllWorking]

Is the signal from each remote unique? Could you you use more than one set of remote and reciver pairs in close proximity without triggering all recievers at once? Like how your car key remote only unlocks your car not all the cars in the proximity.

[@Guason402tv]

Thabk you. How did you rig up the battery? And what kind of rig did you make tonpower it?

[@Rustyshackleford85]

I haven't seen a video yet that actually explains everything.

[@ianmac2963]

Fantastic ,,, EXCELLENT ... thank you VERY much !!!

[@KAPERSPISOWIFI]

Power supply for relay is different from the power supply for the light that it will control? How many volts is the led light?

[@RND-USA]

Interesting! I have one that looks very similar but it’s from Qaichip. Instead of pressing the button to change modes, you use wire the unit in different way (in some cases with an additional thin jumper wire) to set it manually. Does your unit have a button that will allow it to forget the default remote codes and / or learn new codes?

[@technoreview85]

Yes you can reset & it can learn new code

[@imtiyazahmed7365]

Very helpful

[@etherdominicgpoot9191]

What to do if the led in the relay is working but the current is not flowing to the NO even if I clicked the button but works in the NC

[@15KHz]

Hi, I've tried using this kind of Wireless Relay with a Zero Delay Gamepad Board where I connected the V+ (12V) and V- (GND) from the floppy power connector from my PC and I connected the terminals of a button like this: [Button 1 +] in the NO (Normally Open Connector) and and [Button 1 -] in the COM (Commoon connector) but sending the signal to the relay activates it but the button doesn't get pressed (like it didn't make contact between the + and the - connector of the button). Also I checked that in the Zero Delay + and - connectors of the button there's a voltage about 4V. I didn't expect that the button connectors had voltage between the terminals. I find it's weird that just making contact between the fast-on terminals of the button triggers it but when connected through the relay it doesn't acctivate the gamepad button. Have you ever tested it with a Zero Delay USB Gamepad? ... or *any gamepad* ? I ask this because I used it for instance to make a switch to make contact between a data pin in my parellel port and a GND pin in parallel port but I fried my motherboard. I'm scared I could fry something else when using the relay to make the contact. I hope you can give me advice with this. Thanks in advance!

[@kelennaanyanwu5372]

Very helpful. Thanks you.

[@sacvasanth]

Very nice 👌 thanx man.

[@benecarlopetrasanta6013]

is it okay to use the 18650 as power?

[@Rustyshackleford85]

You have a video on using it as a wireless igniter? Ive been looking for days.

[@rajdattani1507]

Very well demonstrated, thank you! Can you have 2 different connections on this module so that the 2 buttons operate them individually? “Button A activates and deactivates 1 light while button B activated and deactivated a different light”

[@technoreview85]

Thank you. This module has a single relay so it can operate any one channel but if you want multiple channels you can choose same module with dual channel relay which is available.

[@rajdattani1507]

@@technoreview85 That’s very helpful! Thank you so much

[@ranilrajapaksha9001]

Excellent, Thanks

[@RodneyDoesMagic]

Where can I purchase this exact one?

[@fastback777ray]

Can this remote be used for car central locking? If they same frequency

[@technoreview85]

I think you have to use learner remote. If remotes are in same frequency, thereafter needs to match keys code

[@user-jm9ep3zp5g]

so i would use mode 2 for garage door ?

[@ronaldd.1355]

I have one of that, but strangely when I activate my device for a long distance (say 30 ~ 50 meters away) it works, and IF i deactivate it, for a strange reason it is not turning off, unless I get much, much closer to say: 10 meters. WHY?

[@hiteshbhaliya8442]

It is need to connect every time? Or only first time?

[@technoreview85]

Only for first time

[@Norman2Galindez5]

can you put 2 mini fan 5v in relay

[@dhakshinamoorthy6339]

What is the maximum distance which can be used

[@atexs4622]

I bulid horn whit this modul but very short rf range how to extend long range? or my modul is not working ?

[@technoreview85]

But my module's range is fine. I have checked it

[@jimbossemi-customs3129]

Very well explained my friend. Subscribed and bell on!

[@SuccessLibrary236]

Can we use 3.7v input?

[@twopiecez5226]

How to clone the module only?

[@creativitymeetsinnovation]

Sir, can I use any RF REMOTE? Will it work with any IR Remote ? Please do reply..

[@technoreview85]

Yes it supports different remotes with 433mhz

[@malaymondal280]

Then how it will used to door lock system

[@TechExperiMents2010]

Love you bro best video

[@rbansal427]

Can multiple remotes be used with a Single module?

[@technoreview85]

Yes...you have to use learner remote or you can buy this module with two remotes which is available

[@jorambritstra2447]

Why do you need the second battery if the switch is already powerd

[@msaran8919]

Is remote m battery lgi hui aati hai,,,,,,ya apne ko dalni parti hai

[@msaran8919]

Mera remote kaam nhi kr rha,,,,,,plz help me

[@jaisg1796]

Hai need this how to buy in Singapore can you send to Singapore

[@technoreview85]

You can search for "Single channel RF remote relay" on any online shopping site.

[@dinar9692]

Is it possible to use one remote for 2 relay module?

[@technoreview85]

Yes..you have to use different buttons & same remote, receiver module. A little bit tricky

[@IqbalMiah-v9v]

ডিভাইসের দাম কত

[@vickykumar4377]

Ye kha PR milega

[@technoreview85]

Description me check kijiye

[@kayone8571]

Friend I’ve subscribed please help me I’ve just set mine up to on permanent and a off b I want this mode and I want flash on off what do I need to program could you reply I’ve subscribed ❤

[@technoreview85]

Yes. You can use two different mode. You have to do pairing proses for 2 times. Follow video instructions for defferent modes. Thanks

[@rajukhaire5858]

Raju

[@Midget_X]

Der dur Der da Der Der da der

[@asadalitc]

Katnay ka ha ya

[@hackeranonymous716]

Hindi me video bnaya kro