ADO A20 / A20F / A16 S866 LCD - Complete Settings Walkthrough (P01-P20)

[@TechTronic9000]

ADO bikes & accessories are available from the official shop bit.ly/OfficialStoreADO ADO spare & upgraded parts can be found on the official AliExpress store bit.ly/OfficialStoreADO_AliExpress You can now also join the Official ADO users group facebook.com/groups/adobike01

[@fernandoriveros566]

Hello sir. Can you help me? I bought a zip swft bike which have kind of the same settings on the lcd screen. I don't know what happened, the pedal assist stopped working. I did everything you showed but is not working. Can you help me?

[@BrunoCrisman]

P17: Cruise control, keep + or - pressed (I don't remember) until cruising speed begins, indicated by the icon on the display

[@saesii]

DEFAULT SETTINGS 🙃: P01: 2 (Display brightness) P02: 0 (Km or miles) P03: 36 (Nominal voltage) P04: 10 (auto sleep timer minutes) P05: 0 ( power assisted mode ) P06: 20 (wheel diameter) P07: 1 (number magnets motor) P08: 25 (speed limit, increase to 44 for max speed) P09: 0. (non zero start, 0= no pedal needed) P10: 2. (drive mode, electric, assisted or normal bike) P11: 2. (assist delay since pedaling started) P12: 3. (Strength of acceleration) P13: 12 (PAS sensor) P14: 15 (controller current limit) P15: 29 (battery controller voltage limit) P16: 0 (reset odometer, km to 0= new bike) P17: 0 (cruise control) P18: 100 (Display range adjust) P19: 0 (0 gear assisted) P20: 0 (controller communication mode)

[@TechTronic9000]

Thanks, that is also useful.

[@mrdaveo735]

Do you have the factory default settings for the A16+ ?

[@dtz1000]

Thanks. I needed that after I messed around too much with the settings.

[@TechTronic9000]

P06 is different, should be 16, the others should be the same.

[@Nuffflove]

Nice one bro that's a big help...

[@TheLinposterIsSus]

Summary for y’all: P01: Brightness P02: Km or Miles P03: Voltage (Only effects how battery gauge reads) P04: Control panel sleep time P05: More assist modes P06: Wheel diameter P07: Number of magnets P08: Speed limit P09: Start with pedaling or not P10: 0 = assist 2=both HAVE ON 2 P11: Assist delay P12: Acceleration P13: Pas sensor (DO NOT TOUCH) P14: Limit to prevent battery damage P16: Reset odometer P17: Cruise control P18: Speed tuning P19: Assist or electric mode P20-P22: DON’T FUCK WITH

[@petelato]

thank you!!!!!!

[@BigDawgKaos]

I only got p1 through p7

[@delboyfc74]

hi there today when im cycling my electric bike the clock is just stay at o mph the bike is work but the clock wont change have you any idea thanks.

[@alvaroq2024]

⁠@@delboyfc74I probably have the same problem. MPH locks, but can still use the pedal assist on my EDISON ebike! Currently checking out other videos on how to reset the s866 to factory settings!

[@romeocruz92]

T

[@tuscan440r]

Listening to you explain the settings rather than trying to decipher the manual was so much easier! Big thanks from the UK :) 👍

[@TechTronic9000]

Glad it helped!

[@daveroche6522]

Well said. Thank you from Ireland also (howdy, neighbour....).

[@AC_Milan1899]

Excellent video. The only KZbinr who actually goes through the settings

[@TechTronic9000]

Thank you!

[@todotvstreaming]

Hi there. Thanks for the great video. My ado A16+ only has 3 assist and throttle only works on assist 3. If I change it to to 5 assist, does the throttle work in all levels? I am curious to know. Thanks

[@DARTraderMediaProductions]

That was the most complete video of how to set these up. I have just ordered one of these as my controller has gone bad and was wondering what happens if I remove my battery from the bike to take indoors to charge. Does the display loose all the settings and have to be re-programmed again when I put the battery back ? Many thanks for the video and I await your reply.

[@TechTronic9000]

The setting will remain saved even you remove the battery, so no need to reprogram. Thanks for watching my video and consider subscribing ;)

[@DARTraderMediaProductions]

@@TechTronic9000 Thanks so much for that, My controller and display arrived this afternoon. I have installed them and find the pedal assist will not work but the walk assist works when I hold the - button down. I maybe need to look at the settings when I have more time. Thanks again and I have just subbed.

[@TechTronic9000]

Check motor magnets, and check assisted sensor type settings, also adjust the assist delay.

[@DARTraderMediaProductions]

@@TechTronic9000 Thanks for that, it appears the problem is with the PAS sensor on the crank. It's wired colour for colour on the plug and the LED on the sensor flashes as I turn crank but no rotation of motor. If I touch the blue and black wires in the PAS sensor plug from the controller together at one second intervals or faster the motor runs fine. I guess the sensor may not be compatible with the controller, any thoughts would be great. Thanks again.

[@TechTronic9000]

Maybe the sensor wires are not corresponding with the controller one.

[@tvbridge]

P01....Brightness 1,2,3; P02....Km/m; P03....Voltage 32/48/60; P04....Sleep time minutes; P05....PAssist number of modes; P06....Wheel size inch; P07....Magnet number in motor; P08....Speed limit; P09....Start level of PAssist; P10....2=Peddle & throttle Assist; P11....Boost sensitivity=1; P12....Boost start strength; P13....Number of magnets; P14....Current limit in Amps; P15....Low Voltage power off; P16....Clear milometer; P17....Cruise enable/disable; P18....Speed ratio % adjustment; P19....1=Direct Hub 2=Gear Hub; P20....Protocol=0000

[@swangodesigns]

So my a20 is not the same brand but it is an a20 same controller.. the speed limit only go from 1-45 but at 45 it still limits to 29 mph... okay.. but my question is this... if I change the voltage cut off which is at 29.. say I turn it down to 25... theoretically I will get more miles before the bike shuts off from low battery but will it ruin my motor or anything else?

[@tvbridge]

@@swangodesignsThe Voltage cut off is to protect the battery, not the motor. Allowing the Voltage to go too low wears them out quicker, as well as potentially killing them.

[@3DPDK]

@@swangodesigns 🔹reducing the cut off voltage *will damage your battery!* but not the motor. Lithium batteries do NOT like to be deeply discharged. 🔹If the motor controller you have uses the amperage limit setting (P14) from the panel (it may not), increasing this may increase your top speed. *Be careful* and don't adjust this number over the battery output or motor input capacity in Amps. This CAN fry the controller and burn up the windings in the motor if you exceed their amperage rating. 🔹Just to be sure: If the motor is rated 750 watts @10 amps, DO NOT increase the output limit over 10 amps. 🔹The battery also has a maximum amperage output. This depends mostly on the battery cells used to make the whole battery. If the battery has a low total amperage output this will effect the top speed of the motor. Normally a 14 to 20 Ahr battery feeding a 1000 watt motor, with a nominal cargo weight of 145 lbs, 29 to 30 mph is pretty much top end performance.

[@bacardionyt4980]

How the cruise control works is once you turn it on, You use the throttle to get to the set speed you want, Then you hold the down button on the display. It takes up to 20 seconds to activate it you'll see a P. Other bikes that I have it activates way quicker but would this controller it's quite slow to activate. So basically get your set speed do you want then hold the down button. If you start pedaling or touch the throttle on this controller it turns it off instantly. On my other bike you can pedal or throttle and then let off and it will stay at the set speed original. Also using the brake will turn it off.

[@SleepyBaseballStadium-qj4wu]

Please tell me adjust colorway electric bike 26

[@paulreid1710]

Thank you. The very best explainer on KZbin.

[@TechTronic9000]

Glad it was helpful!

[@paulreid1710]

I've noticed my stem is wobbling after a few weeks. If you have a video on that, I'd love to watch it.

[@minimoren5905]

Can u get default settings back ?i did reset the whole display som my 48 volt bike doesent have the correct magnets in the wheel and such 😢i would be happy for answers i know its a old video but i chance 😅

[@TheDarkospartan]

I have hitway bk11 and ive changed it to 100 speed limit but it still doesnt go past 25kmph is that because i dont have a throttle? Can it go past the limit in pedal assist mode? Very gratefull for any reply.

[@TheDarkospartan]

I found out I had to change p08 setting to 67 instead of 100 and that worked hope it helps others.

[@MrWrr3rd]

Is your throttle broken? My BK11 has a throttle

[@michaelsavva4853]

Thanks for you help, do you know how to reset it back to factory settings?

[@TechTronic9000]

There is no reset to defaults. You just need to set each parameter correctly.

[@GaryInAmsterdam]

DEFAULT SETTINGS : P01: 2 (Display brightness) P02: 0 (Km or miles) P03: 36 (Nominal voltage) P04: 10 (auto sleep time minutes) P05: 0 ( power assisted mode ) P06: 20 (wheel diameter) P07: 1 (number magnets motor) P08: 25 (speed limit, increase to 44 for max speed) P09: 0. (non zero start, 0= no pedal needed) P10: 2. (drive mode, electric, assisted or normal bike) P11: 2. (assist delay since peddling started) P12: 3. (Strength of acceleration) P13: 12 (PAS sensor) P14: 15 (controller current limit) P15: 29 (battery controller voltage limit) P16: 0 (reset odometer, km to 0= new bike) P17: 0 (cruise control) P18: 100 (Display range adjust) P19: 0 (0 gear assisted) P20: 0 (controller communication mode)

[@lbdchannel7376]

Thank you so much for tge explanation. I have a question, how to clear Error 30 on the display? Thank you

[@Waldwaerts]

Thank you so much for taking the time and explaining it so thoroughly - gonna go tune my controller now and will KNOW what I‘m doing ;) Thx again!

[@TechTronic9000]

Glad it helped!

[@pauldilizia2368]

Great video! Thanks Was wondering, my throttle suddenly stopped working and is not engaging? The only thing is it got some heavy rain on it, but I am sure this would not of affected the throttle?.. any ideas on what might of happened… powers working and everything seems to be in check otherwise Thanks in advance

[@TechTronic9000]

Maybe you just disabled it by pressing power & brake, check my other reviews about ADO controller & the newer method to enable throttle.

[@jameelabbas6469]

Hellow sir i want to ask something, I have doutts c29 ebike, Am using P03: Setting on 48v And my ebike also supporting 48 but my battery didnt give me good performance, It'll get low very early. So i want to ask can i use it as 36v??? Or its can be damage my controller and motor??? Plz guide me sir.

[@TechTronic9000]

If you set it to 36V you will over discharge it and destroy the battery.

[@edulimb4]

Great explanation! Thank you! I need help: all is working fine on my bike, but today it stopped showing the speed and registering kilometers, then it worked again later, now it's not working anymore. What could be the reason? Thank you!

[@edulimb4]

I forgot to mention the bike: ADO A26

[@flip511]

But how can you disable the throttle?

[@Gatitasecsii]

Change setting P10, it can be 0, 1 or 2, but apparently its different in some bikes. On mine 2 means pedal only

[@yasarsalar]

Thank you , You helped me a lot. My S966 display parameter was confused, thanks to you I set it correctly again.😀

[@TechTronic9000]

You're welcome!

[@krisztianjuhasz2717]

Hello! Can this bike be tuned? Take this to mean that I want to include a 48V battery. This should increase your range in pure electric mode. At 0:44, you said that this bike knows the 48V system. What should I pay attention to when buying a battery?

[@TechTronic9000]

Yes this bike in particular comes with a a 36/48V compatible controller. The motor will also go fine on 48V. The performance will see a large boost in speed, acceleration and range.

[@tabouretdéchainé]

hi did you know how to enable pourcentage of battery? we can see it when we start the display but that dispawn

[@sevensins007]

very good explanation for the settings , i did not see anything on regards to the Battery Indicator , as mine does not go down with use , so i can not see how much power is left after a period of time , maybe the battery indicator is fulty ? what would you advice ?

[@lalacrabeatz1320]

i dont understand how i can reset the odometer,the p16 can you make a short video for that? will be so useful thanks

[@DyLemmaOG]

What about the main screen not in the settings? I've seen some S866 displays look different with the battery meter at the top and able to show watts/current

[@Nitecrow314]

Mine shows watts and current. I think it is the earlier version of the display as I have had it several years.

[@NEPGaMeRz]

Thanks for this bro u have saved me searching for videos because my pedal assist wasnt working

[@Faded_Vision96]

Wooooow you saved my day, thank you very much sir I knew there would be a smart person as yourself that would know more about sheng milo mx20

[@TechTronic9000]

Glad I could help

[@Faded_Vision96]

@@TechTronic9000 you did sir thank you very much

[@justynssagan6156]

Can i fit a bigger battery on the a20f like a 48v 17amp

[@TechTronic9000]

Not in the frame as the space is limited, you need an external one.

[@ilkeryoldas]

Thanks! I got a new Himo z20 and it has this controller instead of old with 2 buttons. Can you also explain how the main menu works? The options I have are: - odo - trip - vol - cur - rm - t1 I'm not what they all mean (except for the first one which is showing km I've ridden so far), how to use or reset the others.

[@johnampheregabriel5091]

Hey, just got a new Himo ZB20. i have the same concern, please let me know if you find out. Thanks!

[@ilkeryoldas]

@@johnampheregabriel5091 I've searched online and asked a couple other channels but no response so far

[@horror11]

thx for the nice tutorial. is there any way to set everything back to default ?

[@TechTronic9000]

There is no default, you just need to set them properly for your bike model.

[@georgek1979]

great help, can you pls explain how the manual 7 shimano gears work? Can I use them when the bike is on electric mode (not talking about the throttle, I don t have a throttle)

[@TechTronic9000]

You can use them like on any other bike, you can freely select gears while pedaling so that you get the speed and cadence that you are comfortable with.

[@User-ik2kc]

When I start it up it shows that there is a battery percentage section. How do you get that active on the screen?

[@TechTronic9000]

That is just a test for the LCD screen. The controller is not programmed to show the %, you can use the "VOL", voltage for even more accurate monitoring.

[@mufcbebb]

Hey guys hope someone can help, im very new to this, i bought a prebuilt ebike and had a spare 3 pin connector (orange) ive bought a thumb throttle 3pin (orange) but when i connect it i get a E07 error on the bottom of my display. Would anyone have any idea of whats happening please😂 thank you!

[@dannysale9334]

What color are the throttle wires on the controller? You might want to try changing the PO # 9 setting

[@mufcbebb]

@dannysale9334 All wires are black over the bike and the spare connector slot is orange if that makes any sense I'm guessing my wires have and plastic around it to cover them up, again still new to this I have no idea on anything so my apologies if that the answer you was expecting 😭🤣

[@michaelplowman2481]

P08 has not allowed me to overcome 15.5mph limit it only adjusts the percentage of 15.5mph so at 100 it does 15.5 and at 72 it does 11.2mph, how do I overcome this

[@TechTronic9000]

You can get 35km/h when you use the throttle in assisted mode 3/5.

[@MrGoodizer]

Hi, thanks for the video. My S866 Display does only provide programs up to P16, next it jumps back to P01. I can't access P17-P20. But I need to change the protocol (P20), because otherwise it isn't compatible to my bikes controller. Do you know what I can do to access P17-P20?

[@TechTronic9000]

If you have 16 settings then it's a newer controller model, there is nothing to unlock. Some settings are the same for both.

[@MrWrr3rd]

From what I've read, P17 to P 20 aren't useful anyway

[@ksrx04]

Hi! I got my A20F for about 4 days now. I'm in Hybrid mode using the throttle in the third assist mode. When I'm in the second assist mode I get pedal assist until 25 km/h. Unfortunately it feels like I'm pedalling ''air'' even when I'm in 7th gear (It feels very light). I want to be able to give more power myself so the bike doesn't have to give so much motor power and let the battery drain faster.

[@TechTronic9000]

Check my other videos where I show how to enable 5 modes for hybrid, you will have 3 assist modes and 2 electric throttle modes. Also you can upgrade the chain ring for a bigger one. You can also join the user group for more ideas and mods: facebook.com/groups/adobike01

[@ksrx04]

@@TechTronic9000 Which video? Link?

[@TechTronic9000]

have a look at this, the display is different but the settings are the same kzbin.info/www/bejne/qYqTaY14adB0kKs

[@Chafik__sm]

Hello, I wanted to ask you when I enter the hidden menu to increase the speed of the electric bike, what should I put in the hidden menu of P02 P03 P04 P05 P06 P07 P08 P09 P10 P11 P12 P13 P14 P15 each number of P02 P03 P04 P05 P06 P07 P08 P09 P10 P11 P12 P13 P14 P15 P16 under yours there are other numbers. What numbers should I put in for the electric bike to go at full speed? I have a 750w 48v motorcycle

[@TechTronic9000]

It depends on your display and controller, usually P08 is the speed limit.

[@adeboyefaturiyele2182]

Please concerning P10 from what settings can you disable and enable the throttle I will like to choose either assisted or electric Thanks

[@MrWrr3rd]

From P10 1- PAS only 2- PAS and throttle 3- NO PAS! throttle control only

[@anio6865]

Are we supposed to click any buttons in order to save the settings ?

[@YasAdele90]

I am buying one of these it’s brand new they replaced lcd. It goes full electric mode slow and fast but they are saying the manual throttle doesn’t work or the brakes so they think the controller isn’t working. Can you help?

[@bennychewDev]

Thanks for this video, very handy! I just bought a ADO A20+ international and I tried to unlock the speed limit. Already set P8 to 100 and P5 to more levels of assist. But yesterday when I tried it I could not go faster than 25 km/h. Don't know why... Does the 35 km/h only works in hybrid mode with throttle or does it also work with electric assist? I didn't receive the throttle yet, so can't try that.

[@TheDarkospartan]

Did you need throttle I'm having the same issue.

[@MrWrr3rd]

More levels of assist will not give you more speed. I'm not totally sure about your E-bike model but mine has 3 levels. If I change it to 5 or higher, it just basically continues assist levels 3 to the highest assist level "number on display"

[@tonisuredajuli7]

Hola muy buen video, una pregunta en el P09 arranca desde la primera pedalada? O hay que esperar dos pedaladas igualmente? Gracias

[@TechTronic9000]

Puedes ajustar el retraso desde P11, tiene 24 niveles de retraso que puedes ajustar.

[@tonisuredajuli7]

@@TechTronic9000 entonces si lo pones en 24 desde el primer instante ya te asiste?

[@raulp3453]

@@tonisuredajuli7 el p09 activa el control del acelerador para que actúe desde parado o llegando a los 6km/h. Si lo dejas en 0 y tienes activado el modo híbrido o eléctrico puro es como si fuera una moto. El p11 es un delay en segundos de la asistencia. Mejor dejarlo en 0

[@3DPDK]

The best video dealing with this.👍 I have to include that these are the same settings on the EN06 control panel, however the documentation is either very ambiguous or completely lacking for some of the settings pages. Your explanations have cleared up most of these mysterious settings. A note to other viewers: Although the panel may have an adjustable setting, whether or not it has an effect on your bike's behavior depends on the model motor controller you use.

[@TechTronic9000]

Thanks and also very good note about the compatibility with the motor controller.

[@gregoryhewson3691]

Can you confirm if the Colorway BK15 is able to do this process to improve the speed?

[@TechTronic9000]

Sadly I do not have experience with this model.

[@valensu4039]

Thanks for the video. I have a question. When I start pedal and electric motor start running too. But when I stop pedal the motor will keep running about few seconds. Witch one can adjust when I stop pedaling motor will stop right away. Thanks again !

[@TechTronic9000]

Check the assisted delay setting.

[@MrWrr3rd]

Just lightly pull brake lever

[@Dinotti]

U have settings to P20 i have only to P16. How to unlock it and to make accelerator to work?! Tried all settings u showed, but it doesnt work.

[@TechTronic9000]

You probably have the new controller, check this newer video for that one kzbin.info/www/bejne/qH2TgWydjJqrarc

[@dannysale9334]

What color are the throttle wires on the controller...

[@harryryan3592]

I just got an A16 this week was working perfectly, but I noticed over the last two days only the pedal mode assist was accelerating me and not the right trigger. It seemed as though the right was broken but I don’t know any ideas ?

[@whitecloudmountainminnowpr6353]

Hello . If I set it to a smaller wheel size will it make the motor go faster if it thinks it has to make up the speed

[@TechTronic9000]

No, it will just show wrong speed as that setting is just for display calibration. You can check my other related videos about ADO bike to see how to unlock them.

[@whitecloudmountainminnowpr6353]

@@TechTronic9000 ok thanks . I will do . My bike was limited to 15 mph I've unlocked that but my bike only does about 19 or 20 mph if I peddle really fast. Hopefully I can get it abit faster

[@MrWrr3rd]

Best bet... Go on a diet. I max my Hit way BK11 (US edition) at 22mph gps calibrated. If I wasn't 260lbs and was closer to the 70 kg little boy they used to get the bikes specs I would probably rip lol😂. Oh, another think you can do to get your bike to go faster would be too get a 60lb neighborhood kid to rid it. I mean you won't be on it but your bike will haul a55 . Lol

[@whitecloudmountainminnowpr6353]

@MrWrr3rd I have a 1000 watt hub kit now with a 52volt battery . Much better

[@dresmart432]

Hi . Thanks for the good reviews but my A20f does not have trottle response. Do I have to upgrade the controller ??

[@TechTronic9000]

Do you have the old or new controller? For the new one this is how to enable the throttle kzbin.info/www/bejne/qH2TgWydjJqrarc

[@dresmart432]

@@TechTronic9000 thanks for the reply. I do not know. I have to see what controller I have installed...

[@totaljustice1582]

Should the voltage be set to match the battery? My battery is 48v, so should I set it to that? Or is under volting okay? I got my bike second hand and all the settings have been changed for max speed lol so I wanted to make sure all the settings are okay. Don't want to damage the battery

[@TechTronic9000]

There are 2 voltage settings, one is for the cut-off so you don't over discharge it, while the other is for nominal voltage so that the controller know hos to display how much % battery is still left.

[@fuadbayramov7989]

Hey, thank you for video. Very useful. Is it possible to show battery life in percentage “%”? When I turn on the display I can see for a few moments percentage and then it will be disabled. By pressing power and “+” button I can enable Max (MAX) and Average (AVG) modes. But I can’t switch to Distance (DST) mode. Can you please help me? Thank you in advice 😊

[@TechTronic9000]

Battery is displayed only as "bars" and accurate as voltage.

[@sogalog1]

Hi great video I bought my bike a couple of weeks ago The throttle does not work even after your set up advise I complained to the shop and asked for a new throttle this arrived eventually I fitted off the bike went through the set up but still does not work would this be a faulty controller

[@TechTronic9000]

You need to enable the throttle from the settings, also enable zero start. Also if it's the new controller check my videos regarding it. You also need to enable throttle mode on it.

[@stevestroud6354]

My bikes odometer and speed is off compared to a GPS unit I have. Which setting do I use to adjust this? My display is slower and shows fewer miles than the GPS unit. Thanks in advance for your help.

[@TechTronic9000]

From wheel size.

[@David-wr3lj]

Hi, i have the same display on my bike but do you know how to factory reset so the settings go back to same as when bought at all please?

[@TechTronic9000]

There is no "reset" for this display. You need to set each parameter properly.

[@savvasarampatzidis4268]

Hallo i have urbanglide ecross pro boost 1600 i must do the same procedure to unlock the speed limit?

[@wiseiisous]

Excellent video! I only have one question. What should I do to reset the odometer? Do I just push the minus button to reach the 0km?

[@MrWrr3rd]

What you're probably going to do is go to the odometer setting and then push and hold (-) button. I doubt it but it may also be the power button, having to hold that

[@AbdulKarim-x1w]

How to save changes because every time I put the correct details it does not save when I switch off and on again it goes back to factory settings also does not display accurate speed

[@mohamedamin6752]

I almost sold my bike and start looking for a new one !! U saved me bro !! Thx 🙏 😅

[@TechTronic9000]

Glad I could help!

[@gatzish]

Hi there I have the new controller with the 16 settings,but cruise control is not enabled. Is there a way to enable it?

[@TechTronic9000]

You can check my other videos where I have covered the new controller, mine worked right out of the box with cruise control.

[@krisztianjuhasz2717]

Hello! Is it possible to set the display to show the battery voltage as a percentage?

[@TechTronic9000]

No, but you have Vol indicator for "voltage" and it's more precise.

[@dublinese415]

hey what would be the best setting for battery under voltage protection thanks??

[@TechTronic9000]

Not lower than 32-33V for longer lifespan, you can even choose 34V but it might cut out too early.

[@sogalog1]

Hi have to mention the other problem some bikes are sent out with throttle disconnected and have the new controller fitted To unlock you have to hold right hand brake and full throttle in off position turn on bike wait 10 seconds then turn off then back on then the motor will work

[@TechTronic9000]

Then you are lucky you got the new generation controller, a very wanted upgrade part for our older initial ADO bikes. You can check my other videos in regards to this matter.

[@Yahoomediaclub]

Can you please help me to get my throttle mode back on .. I have E 08 on screen. I think the problem that caused it was after I carried a bag over the handlebars and it maybe has hit something like the horn and lamp buttons.. not really sure tho.. that was directly after this happened (No Throttle) Ado A20F Thanks for great videos.

[@wiseiisous]

Hello. Excellent video mate. I just got a second hand ADO A20 and I try to reset odometer but I can't do it. I am at P16 pushing the minus button to change my km to 0 but nothing happens

[@luukverburgt]

I have a dyu a16 so it's not the exact same controller but it looks a little like it but i cant go to p8

[@zeze970]

Hi from portugal Can whe wash bike whit water whit no problems? Is there any precautions? The whole to unlock battery can enter water and damage electric part?

[@TechTronic9000]

Not with power wash, but with wet sponge / bucket it is ok.

[@craftman780]

I got my first ebike a few days ago. I'd like to change the displayed speed for the bike (max, 21MPH) but it shows 35-40MPH which is wrong. I would adjust the P18 parameter?

[@TechTronic9000]

Start by checking wheel size first.

[@craftman780]

@@TechTronic9000 26" wheels.

[@GaryInAmsterdam]

This doesn't sound right. I would change it back to the defaults and carefully watch the video again. You want it to go faster or just display the correct speed? DEFAULT SETTINGS : P01: 2 (Display brightness) P02: 0 (Km or miles) P03: 36 (Nominal voltage) P04: 10 (auto sleep time minutes) P05: 0 ( power assisted mode ) P06: 20 (wheel diameter) P07: 1 (number magnets motor) P08: 25 (speed limit, increase to 44 for max speed) P09: 0. (non zero start, 0= no pedal needed) P10: 2. (drive mode, electric, assisted or normal bike) P11: 2. (assist delay since peddling started) P12: 3. (Strength of acceleration) P13: 12 (PAS sensor) P14: 15 (controller current limit) P15: 29 (battery controller voltage limit) P16: 0 (reset odometer, km to 0= new bike) P17: 0 (cruise control) P18: 100 (Display range adjust) P19: 0 (0 gear assisted) P20: 0 (controller communication mode)

[@craftman780]

@@GaryInAmsterdam Display the correct speed

[@mrcoco3562]

Can i switch on and off for PAS mode and throttle mode? And do this meter able to work on all controller?

[@dannysale9334]

Yes po #10 setting

[@seanpatterson9244]

Is that on a panther e movement? I just copied all your settings , it feels so much faster , p19 cruise control I had to turn off , it’s bloody scary:)

[@GaryInAmsterdam]

I tried all these settings as well and the torque was too strong and bike was too fast, at least for me living in a city. So I found a nice combination which also saved the battery life.

[@seanpatterson9244]

@@GaryInAmsterdam how fast was it able to go

[@GaryInAmsterdam]

@@seanpatterson9244 The top speed I obtained (out of the city on a quiet flat cycle path with no wind was 35 kph. I weigh about 78 k and have my backpack and computer on me. But it was the startup speed that scared me in teh city after changing some settings. The bike would go from zero to 20 in seconds. Yeah, the cruise control would kick-in all the time too! I found a happy-medium setting which helped sustain battery life. I haven't used it much later since I don't commute as often.

[@seanpatterson9244]

@@GaryInAmsterdam that is quick! Nice on a flat clear road, but around a crowd I imagine it isn’t very nice , especially because the bikes turning circle and movement isn’t as easy as a standard bike , and that cruise control I found was horrible at top speed . Leat you found a happy medium now the more comfortable you are the safer you are :)

[@TechTronic9000]

This is an ADO A20, but this display is rather popular and used on other bike brands also.

[@stephensmit6570]

My hitway BK5 has this controller, but now suddenly on assist level 3 it now goes to 21mph. The speed limit was set tk 25kph, Ive gone in this menu to lower the speed limit and it still goes to 21mph, how do I remedy this?

[@SagarPal02]

Very informative video Sir.. Thank you for this. I have a Emotorad t-rex which has this display unit. Due to restrictions in India i'm unable to go beyond 25km/h. Now I set it to 35km/h it runs more faster than usual. Thank you ❤️

[@TechTronic9000]

Glad it helped

[@WildCash1-eh4go]

The mileage will decrease riding at 35 km

[@hasandogancc]

Hello, it says 04 on the screen. What path should I follow?

[@ilkeryoldas]

I've tried unlocking the speed from p08 menu (I set it 100) but speed is still limited to 25. Is it possible that it's locked in hardware? My himo z20 doesn't have the throttle handle like in their older versions btw, it only works when I pedal.

[@simonedoniselli657]

I have the exact opposite problem lol

[@fernandoriveros566]

What level would you recommend to set on p12? My pedal assist stopped working suddenly I'm.not sure if I moved it without noticing

[@TechTronic9000]

Check all the wires and also check the sensor to still be seated in the proper position.

[@fernandoriveros566]

@@TechTronic9000 where can I find the sensor on my bike? It's a Zip swft bike

[@TechTronic9000]

It should be on the pedal shaft

[@DJESHGAMING]

When i change assist delay to 1 there is still a big delay. Is this normal for this bike? Its pretty annoying sometimes. Have to peddle 5 times even at setting 1

[@m1ka007]

i have the same question

[@TechTronic9000]

Try to set it to 24 (as it ranges from 1 to 24), should be almost no delay. It's confusing as the setting seems to be reversed.

[@TechTronic9000]

Try to set it to 24 (as it ranges from 1 to 24), should be almost no delay. It's confusing as the setting seems to be reversed.

[@DJESHGAMING]

@@TechTronic9000 at 24 there is very much delay

[@jordyshaw6987]

Hey I got my ADO A20+ the other day, loving it. Im unsure how t oactivate cruise control though, any ideas? Pretty sure mines the new controller.

[@teehung5125]

Cruise control can be activated by holding and maintaining the throttle at the desire speed for 5 seconds

[@TechTronic9000]

If it's the new one, the cruise control activates after keeping throttle constant for several seconds.

[@MrWrr3rd]

You may have to do that and also hold (-) for approximately 5sec. I have an S866 display.

[@andersonmarcelo455]

Thank you so much. I have an A26 and this video helps me a lot. I just have a question: Is it normal when I go through a hole in high speed, the display shuts down and sometimes it's hard to turn it on again. Many times the display only turn on if I push and pull weakly the battery.

[@TechTronic9000]

You have a loose plug or connector, I would check all the plugs and wires.

[@tylercracker3373]

I got an E10 coming up on the bottom of my screen and then when I go out mine doesn't go very fast anymore what can I do

[@TechTronic9000]

Usually E10 is a communication error. If your bike has a headlamp try to disconnect it and see if the error clears.

[@sogalog1]

Once again thank you for your reply I set it at 000 on program 9 but throttle still not working even after replacing throttle It must be the controller at fault as I have set all programs as suggested thank you

[@TechTronic9000]

Is it the new controller version? That needs activation for throttle with a different procedure. You can see both controller and how to replace them: kzbin.info/www/bejne/hqrPZINuqc6snqM then you can follow up the test ride where I explain more about it and show how it works: kzbin.info/www/bejne/qH2TgWydjJqrarc

[@MrWrr3rd]

PO9 set to "000" will disable throttle. Try PO9 set to 002

[@kaloampeli]

Hello i have joust bought ado 20 and i have a problem with the throttle, is is not responding as it should be .I have made the adjustment as you describe in the video but i twist the throttle but it is not working .I only have petal assist..can you advice something

[@TechTronic9000]

Maybe you have the new controller so check this video here to see how to enable it kzbin.info/www/bejne/qH2TgWydjJqrarc

[@Kowal.77]

Hi sir, i need to change my wheel diameter setting because my km/h meter is not accurate, but i cant change any setting besides p8 and p10, do you maybe know how to change it?

[@TechTronic9000]

Is it an ADO bike? Maybe it's another controller?

[@Kowal.77]

@@TechTronic9000 no its an ouxi v7 pro.

[@Dwayne898]

Help! I can no longer get the full throttle mode. neither will it go beyond the 25km/hr speed limit. Any idea what the cause is? Thank you for the upload

[@TechTronic9000]

Have you activated the throttle, have you selected maximum (3) assisted mode? Also check P08 setting to be higher than 25km/h

[@Dwayne898]

@@TechTronic9000 thanks! 👍🏾 I was able to fix it - now cruising at 35kmh

[@dehadista2006]

Thank you. I have stumbled on your channel because, I was messing with the settings and I have lost my assist mode though I still have the throttle. What have I done wrong?

[@TechTronic9000]

Check all the settings to be similar with the ones from my video. Do you have the newer controller?

[@dehadista2006]

@@TechTronic9000 I have change all settings. I copied all your default parameters. It's now working properly. Just one thing, I have 0 1 2 3 , 1 is pedal assist which I find a bit of a surprise jolt of speed and I have to brake sometimes because I might hit somebody in the street. is there a way I could tame it a little bit. it's only 1 that works as pedal assist. 2 and 3 are the same using the throttle. Is there something I can do? Please enlighten me and thanks a bunch.

[@TechTronic9000]

It looks like you have the old controller model, you might want to upgrade to the newer controller, that woul give it 3 assist modes. You can also tame this controller by reducing acceleration power (see in video).

[@dehadista2006]

@@TechTronic9000 Thank you very much for the info, I would greatly appreciate it if you make a separate video tutorial about that, I'm sure many have the same problem. Thanks. Btw, I have Cruise activated, that means I have the newer version of a controller?

[@tonyflanagan5682]

Hi, any ideas why my milometer has stopped recording the miles properly (got the first 11 miles done and seems to have gone bad). Also, the battery seems to show low bars very quickly, say after a few miles (4m) of riding part assisted mainly and a bit of throttle and getting 1-2 bars on assist 2 and peddling ( bike is set to 36v ). Bit worrying for a longer journey if I have just got the bike and the battery is fully charged? Regards

[@TechTronic9000]

check all the plugs and wires, check and adjust the brakes, also check tire pressure.

[@MrWrr3rd]

Also check your tire diameter. If you accidentally changed it to something ridiculously small, your odometer might not have registered enough distance yet. Just a suggestion but the values might not go that small

[@lobirdsamart]

Hello i have a problem after messing with the setting now it turns on it won't start it shows - - - - and i can chose the number i cannot get back to normal settings anymore

[@TechTronic9000]

Is it an ADO or another bike?

[@lobirdsamart]

@@TechTronic9000 i found out after searching on internet that i set a password on it that's why. But I did not know that i set password. So i don't remember what the password is i found that 3745 is the password from factory so I could get it work again haha thanks for Ur reply man

[@TechTronic9000]

Glad to hear that you have sorted it out!

[@shahjahanbhatti7413]

Very informative, thank you! I don’t understand the P15 option though. Are you saying you’ve set it at 29V which makes the Bike battery turn off once it gets to this voltage when riding? I’ve got a 12-15 mile commute to work and I plan to re-charge the battery when I get there. My plan is to set the P15 option to 0v or 1v. Is there any harm to the battery in doing that?

[@TechTronic9000]

P15 is a battery over-discharge protection built into the controller. At 29V you are at 2.9V/cell which is already low, going lower that that it will quickly destroy the battery.

[@Nitecrow314]

No matter what the setting is on the display, the bms in the battery will shut down at a safe level (low voltage cut-off). Also, how far cells can safely be discharged depends on which cells they are. Some can safely be discharged to 2.75, or even 2.5v.

[@MrWrr3rd]

You don't want to run it that low as irreversible damage to battery may occur

[@basilpaly721]

How can do totaly reset to factory settings ?? Thank you

[@tobykay2917]

I’ve done all the settings but the speed stays at zero when I ride do I need to activate it ?

[@SimsKerol]

I'm on Skyjet Nitro 16 and After messing with settings, I got "04" error code instead of speedometer. How to fix. All settings are back to normal for now.

[@y.gamer.0706]

I cant see how hard im going the teller shows 0 km but im driving help

[@paulodrichard9635]

can you help me on the manual of this controller says "P12: Help start intensity setting range: 0-5;" and in this videos you said "P12: Electric mode acceleration strength" is this the same? very nice video btw, also i have 1000w ebike with 48V/15Ah baterry and Control system is "48v20a Vector controller" in P14 what setting should i use? 15a? 20a? default number its 13 don't know why

[@TechTronic9000]

It's the same, it's how fast the motor will accelerate. For your second question I can tell you from my experience that the amp setting usually doesn't work, so default or maximum it is the same.

[@paulodrichard9635]

@@TechTronic9000 tks allot for the answer brother one thing i have notice is that ebike seams to have allot more power if i put P14 on 20a , i tested with 12a and seams allot more slower is that anything to do because my battery is 15ah ? or this setting have nothing to do with baterry power!? for the record "P12 was on 5 booth times while testing this. another weird thing that is happening to me now its that KM/H gets stuck on 34/35 even if iam going 40 or even 45hm/h have tested with GPS till 34/35 shows the same as the GPS after that gets stuck there and gps shows whatever more than 35 iam going 40.. 45.. etc.. any clue? sorry for long reapply hard to find help with this stuff online

[@TechTronic9000]

Theoretically P14 changes the maximum allowed current for the controller. This should also be supported by the controller. It has nothing to do with the battery capacity, is it just allowing more power to go to the motor. I have seen this speed freeze on several other bikes when you unlock them and ride fast. Haven't found a way on sorting it out.

[@FN463]

Hello. I watched the video. I still have a problem. I have the Ado xe 16 bike. Same controller. BUT, in PO5 setting, it gives me only 5 assistance levels, NOT 9. Generally, the problem is that it doesn' t reach 25km speed. And I have to pedal too much, just to give me a little boost. I want just to do one-two pedal and then boost. I want the less delay, the more boost, the fastest it can be. What exactly have to do in settings to achieve that? Thank you!

[@TechTronic9000]

Check my other video with ADO bikes, your XE has another type of controller with just 16 settings so you unlock it in other way.

[@FN463]

@@TechTronic9000 Hi again. I watched the other videos but i did not figure out how to unlock speed limit. My ebike is Ado XE 16 (there is no throttle). It has the same controller, the S866. It has two choices for speed assistance. Either max 3, or max 5. There are no 9 levels of speed among my choices. And the fastest it can go is 21km. It never reached 22km. What can i do to go faster?

[@MrWrr3rd]

The 9 levels isn't going to help you at all, especially if the bike only supports 3 or 5 levels. What you want to change are P11 and P12. P11 is the delay before the assist happens (1 to 24) 24 being long delay (personaly, I use this setting to increase distance/batt life) set yours to 1. P12 is PAS acceleration value (1 to 5). Set this to 5. This is how these settings should work. Hopefully it works for u.

[@abubakerhazarewal1052]

Hi. I Have A16 but it doesn't have accelerator and it goes automatically. Do you know how do we control speed if we have to increase or reduce speed. Thanks

[@aicogaming2409]

Good morning ! I have a A26+ and I wanted to know if an improvement for the max speed? I am currently at 35km/h and I would like to have it homologated but for that I have to reach 50km/h Is there an improvement?

[@TechTronic9000]

You can't go faster than 35km/h as that is the limit for the battery, controller and motor. To get 50km/h you will need at least a 52-60V battery, new controller and new motor.

[@Danny-nq9ky]

when I do what you say to do to speed up my bike it doesn't go to PO mode. it goes to C mode what is that

[@farazalam3184]

How shall I turn on the battery percentage indicator?

[@TechTronic9000]

It is not possible.

[@feuer904]

There are similar bikes where I can change the display settings up to 35 kmh?

[@TechTronic9000]

To increase speed and unlock the controller it's not only about the display, the bike should have a battery, a controller and a motor to actually be able to increase power and speed.

[@mdollbot]

hello i connected s866 with brainwash controller but nothing happened when i pressed throttle? i have error 10 in odo mode

[@tonyjones7996]

My s866 only shows a blank screen with all 0 on the bottom and when I turn it on the back wheel goes on its own

[@DJESHGAMING]

Does this also work for the XE versions? Or are those stuck at 25kmh

[@TechTronic9000]

For the XE it's even more simple, it's like on this video kzbin.info/www/bejne/qH2TgWydjJqrarc

[@dublinese415]

hey is it safe to unlock the speed wont damage controller or anytn wud it?

[@TechTronic9000]

It is safe, it just uses up the battery faster.