IR2153 Switching Mode Power Supply 50-0-50 Volts 1000W Dual Rail Voltage for Audio Power Amplifier

[@user-dq8kz9vj3u]

I immediately saw an error in the scheme. The output diode D4 is not drawn correctly. Someone will have a big BOOM

[@Pacmania100]

0:06 A direction of the D4 diode is wrong! The C9 cap may be exploded. :(

[@mladjanilic]

Direction of D4 diode is ok.

[@trisuharto6258]

​@@mladjanilic😮😅

[@hersanwidiatmono4194]

Be careful , Overload protection must be installed so that it is safe, if the load is short-circuited the mosfet may explode

[@VasyVasii]

How the overload protection works ?

[@micheljustnziwa1382]

How to make a system for stabilization the two phases out when we use this ic

[@jeanelins1168]

Amigo qual a modificação que tenho que fazer pra ter 50v 60 ah??

[@devdevan551]

Sir how to add short circuit protection with this circuit?

[@fab35rs]

hello my dear friend how make the transformer? Please put the specifications this transformer, and how make it.

[@abcdef-xb7mi]

Sir can be used 20n50 mosfet in the 20n60?

[@qaisarali97]

Transformer winding use wire SWGS?

[@electronic7979]

Nice

[@catarocktreslar5201]

Schematic D4...Rectifier ( - )...?

[@flytech01]

Capacitor Xploder, nice work...

[@c.schandra2134]

Can I really use fqpf20n60 for 1000w

[@gurilab]

Este é una fuente de 20A?

[@subratasubratakumarpanda9919]

Shall I add a more volt 0-19 2amp

[@emrahinan1]

please fix the orientation of the d4 diode....

[@readingroombd]

Sir can you provide me the circuit diagram and pcb layout?

[@devdevan551]

The gauge wire of transformer. Can be add 12 volts 1,2 Amp with this trans...please idea sir🙏

[@miqueiasmedrado5071]

Hello, I need to change something between 110v and 220v or is the same circuit ?

[@abdul-q-khan]

Why don't you provide gerber file and or the pcb board link of selling if you do sell them on ebay or on Aliexpress???

[@ardhi1269]

No feedback?

[@56pramod]

Diode D2 is missing in PCB diagram FR 107

[@mayurakoongoda9550]

How many amperes of these circuit out please tell me

[@jeanpaulcaballero9883]

para mi pais que se manejan 120vol ac cuantas vueltas para el transformador

[@c.schandra2134]

And from data sheet I am confused with power dissipation between irfp460 and fqpf20n60 Is it its output power explain plz

[@TheSlimShady87]

power didipation is heat disipated by capsule! has no connection with output power! if you need to know about a mos to use just start from total output power split to input voltage and shoul be less than 1/4 from maximum continuous current of datasheet mos, than to see if you disipate more power than it says in datasheet check rds on and see the voltage drop on the internal resistor, times current and that is the didipated power, which should be less than maximum admitted

[@c.schandra2134]

@@TheSlimShady87 thanks for reply I was so confused

[@c.schandra2134]

@@TheSlimShady87 so I must have to know rotal output power and to split to inputvoltage is that the way to select the mosfets for smps

[@susilnishantha3711]

Hai there..........what is the frequency of transformer and operating voltage of the primery is will be 178.5V according to the formula.. is it correct ? I cannot make transformer without knowing frequency.........................thanks

[@subratasubratakumarpanda9919]

What is the transformer turn ?

[@yg22056]

pcb layout?

[@subratasubratakumarpanda9919]

Sir my load is power amplifier. So is it can worked? Kindly make primary & Secondary turn data.

[@shanisharma3043]

Agar purchase karna Chahe to Kaise mile

[@fadielnel]

D4 diode reversed?

[@samvelmarkosyan3684]

Hello mister, I don’t understand in English what you explain, tell me please on the transformer how many wires 2-3-4 lived and what is the ratio of 0.5 or 0.25? and on the secondary, and which transformer, thanks

[@jeanpaulcaballero9883]

amigo el pdf de este amplificador donde lo encuentro

[@АндрейКопыльцов]

после трансформатора нужен обязательно дроссель! в каждое плечо.

[@antonioivanferreyra1953]

Hola, para tener una salida simple de 90Vdc cuantas vueltas debo darle al secundario? Puedo usar EI33? EI35? Sólo necesito 100W

[@maxyfx]

hola al secundario le tenes que dar unas 12 a 13 vueltas.

[@rashidmuhammed7500]

J

[@helenrubyortegaaguilar9285]

How can I get 12V and 5A at the source outputs?

[@ELECTROBUFF]

By simply adjusting the secondary turns

[@soriatel]

Transformer?

[@jeancaballero3813]

Amigo que referencia es el transformador

[@GedersonZeferinodaSilva]

Amigo boa tarde tenta usar o de atx o I33, tenho um projeto parecido com esse que usa esse I33.

[@aliabd463]

hello my dear friend how many turns each coil in transformer?

[@deujeescorrea4022]

qual e sua voltagem de saída? 12VDC? 50-0-50 VDC?

[@ham_predurok]

Так и думал, спасибо, извени только по русски болакаю

[@rasikanuwan1039]

Hello sir. Please let me transformer swg and turns (primary and secondary)

[@qaisarali97]

Please give circuit PDF and transformmer specification

[@mdzisanislam4991]

👌

[@rickytam4941]

D4 diode is wrong direction

[@nurwahidlechery6542]

How much n primer,, & skunder,, thanks

[@salermo42]

Not sure that i miss something but No. of turns are drawn in schematic (25 for primary and 2x7 on secondary).

[@prasanthrs4537]

1.5 cm square area core Primary tuners number and secondary tuners number Please reply

[@el-ectronicsguy5976]

This circuit is not really working, I do not get correct output

[@antoniocalcanohidalgo2853]

Por favor quiero que pongas un diagrama de una máquina de soldar inverter

[@Amplifiertractor]

ETD42 k tarn batao bro

[@AdaletAdaletAdalet.]

D4 diode in this stage is wrong direction

[@fadielnel]

It should be reversed?

[@ELECTROGYAN]

Stop making such incomplete videos show us the practical circuits.

[@subrat40]

Transformed details pls

[@Amplifiertractor]

Transformers size bro

[@ELECTROBUFF]

Core Cross section are is about 3.8 cm2 or use a EE core size 49

[@Amplifiertractor]

@@ELECTROBUFF re 42mil hai bro or ee 49 nahi mil rahi hai bro

[@Amplifiertractor]

EE 42 CORE MIL RAHI HAI EE 49 CORE NAHI MIL RAHI HAI BRO

[@DrHerarius]

0:11 D4 - надо наоборот. А почему однополупериодный выпрямитель?

[@tarkandatdree8064]

หม้อแปลงแบบไหน ครับ พัน แบบไหน ครับ

[@nco6457]

พันวัตต์คงต้อง etd49 ขึ้นไปมั่งคับ pri 24 รอบ sec รอบละ 6vกว่าๆ

[@shaenksb3671]

D4 ในแบบ.. ใส่กลับขั้ว

[@tarkandatdree8064]

มั่วๆๆ

[@HERIYANTO-jj9yt]

Layout plis

[@abdurraheem898]

Please give me pcb layout file...

[@slavazwer4587]

Hello Mr. LOSHARA/ Кого ты хотел удивить?

[@Amplifiertractor]

EE 42 CORE MIL RAHI HAI EE 49 CORE NAHI MIL RAHI HAI BRO

[@jeanpaulcaballero9883]

te falto en el impreso la R6 y la R 5

[@Amplifiertractor]

All components list or price or whatapps no.

[@ananthraja8176]

Transformer input voltage

[@ВасяПитерский-о6т]

No 1000W - nominal ~300-350W.

[@ourchannel8215]

output diode wrong..😅😅

[@tech4usyed528]

Wrong supply it's not +50 0 -50 see diagram

[@tarkandatdree8064]

มีใครลองทำยังครับ

[@nco6457]

ผมกำลังสนใจอยู่คับ

[@tarkandatdree8064]

Have anyone do it ? Pls. let me know thanks alot..

[@alexfed2680]

I did

[@ELECTROGYAN]

@@alexfed2680 what are the results can you share with me

[@alexfed2680]

@@ELECTROGYAN Many. Depends on what do you want to know. In particular: 1. No short-circuit protection. AT ALL. I'm using this schematic only for primary power supply with further stabilizing. 2. Schematic in this video has wrong output rectifier - D3&D4 diodes cathodes must be connected together to obtain +50V output only. Correspondently, C9 must be connected with opposite polarity, lol. 3. Input voltage in this video must be 220/230V only. To have 110V input in this circuit (I don't know what country you are from) you have to install additional switcher to switch inlet rectifier to voltage doubler. 4. IC power supply resistor R1 heats up and heats up much. 5. To calculate output transformer you better use special soft. I can give you a link to download, but interface is in russian:) 6. ... and many more, "Le bon Dieu est dans le détail" - remember it)). BR, Alex.

[@ELECTROGYAN]

Copy paste from internet Make practical circuits

[@tilaktilak2127]

Sir can u send me pdf

[@AdiYustantoNugroho]

dioda wrong direction

[@BJaca-tn3om]

*F A K E*

[@alekseyafanasyev2037]

250 Watt max

[@TheSlimShady87]

tell people to add snuber or else kaboom! ir 2153 failed a lo of times on me because of that!

[@ELECTROBUFF]

👍

[@gyulakurucz8331]

Hi! I designed a half bridge smsp with tl494. Unfortunately the fets are blowed up under load. I didnt used "DC blocking" capacitor in series with the transformer. Someone told me that the reason was the lack of that capacitor because it should make the circuit resonant with the leakage inductance of the transformer. Is it the case? Or I should use a snubber somewhere, if yes, then where?

[@NSluyter]

@@gyulakurucz8331 R3 and R4 are important, add snubber 470pf and 47Ohm and good layout, >=500v fets

[@gyulakurucz8331]

@@NSluyter Hi! R3 R4 isnt required when you are using fet driver ic and powersupply filter capacitor(no oscilation, i checked on scope). But thank for the reply!

[@Amplifiertractor]

@@NSluyter tranfarm size bro

[@Amplifiertractor]

Contact aapke

[@gwantweng]

Video yang menyesatkan

[@alexnet8943]

Fake ! 😂. 2x330uF

[@sajo1280]

LOL I cannot understand a word u are saying. What language are u speaking?

[@stevetobias4890]

If you're going to speak English (which I do appreciate), please slow down. It is very hard to understand what you are saying when you speak so fast. You almost had a new subscriber but I will not watch videos if I cannot understand what you are saying.

[@alirezarafi-ee1175]