The #1 Flight Controller Failure ?

  Рет қаралды 15,047

Livyu FPV

Livyu FPV

Күн бұрын

Пікірлер: 44
@EvilDxtreme
@EvilDxtreme 4 жыл бұрын
Livyu I struggle sometimes to identify or find components once I found the issue. Could you make a video showing and posting links to the most commonly used components? I know in the beginning it was a struggle for me to even find a links to the data sheets for the STM32F405RGT6 f4 mcu. Man that would help many including me I think. Thank you for your teachings sir.
@TheBlaznbowls
@TheBlaznbowls 4 жыл бұрын
Yes that would be awesome
@imager09tube
@imager09tube 3 жыл бұрын
Nice effort Livyu, thanks!
@Theeslickness
@Theeslickness 2 жыл бұрын
Thank you this was really helpful and fun to watch. I successfully transferred an F4 clip using a craft heat gun LOL. Sadly it was probably a waste of time because my other F4 chip was probably defective too. It was fun swapping chips even without your great tools.
@christophen9538
@christophen9538 4 жыл бұрын
I love your electronics diagnostic and repair video. I want more !!! :)
@FlowTfpv
@FlowTfpv 4 жыл бұрын
Very nice! thank you. learned my last bits for today... now gonna sleep and dream of voltage regulators and mcu's.
@tiagonordio
@tiagonordio 13 күн бұрын
Hello, with this magnificent video I managed to find a defect in the flight controller but I ran into another problem, I have a FC marketsys f405ctr and I need a 3.3v regulator and because of the number I can't find it...... the number I need appears on the regulator is "L314" would you have the commercial number of this regulator? Thank you in advance for the video and attention.
@alfonso8544
@alfonso8544 2 жыл бұрын
Hi I have a flight controller that does not work for me the video stream of the fpv camera what could be the fault ..
@Switch180fpv
@Switch180fpv 4 жыл бұрын
So much knowledge in your videos thank you
@alexanderfedorov7890
@alexanderfedorov7890 4 жыл бұрын
Well done as usual mate....
@user-gp8qd5gm1v
@user-gp8qd5gm1v 3 жыл бұрын
I have 1 f3 uploaded wrong fimwer now the light is not on, is there a way to fix it?
@yaronskp
@yaronskp Жыл бұрын
How do you find positive and ground?
@kandredfpv
@kandredfpv 4 жыл бұрын
For me the #1 issue has been the switching regulator burning out on 2 boards. The FC powers fine from USB but nothing from VBat. I also had one case of a failing OSD after a hard crash and another case of a failing motor output which I was able to fix by remapping. Only time I've ever burnt a MCU is when I plugged in an incorrectly wired cable to a 4 in 1 ESC but that was completely my fault, and I was able to replace it and get it going again.
@LivyuFPV
@LivyuFPV 4 жыл бұрын
well from all the FC's I've got from you guys... from kiss to RF and BF the main fault was MCU :)
@naomarik
@naomarik 4 жыл бұрын
I have a FC with same issue -- power from USB but not batt. Got some 5v BECs on the way to fix. Nate Payne recently made a video addressing this issue.
@LivyuFPV
@LivyuFPV 4 жыл бұрын
@@naomarik the 5v is not particularly dead...
@naomarik
@naomarik 4 жыл бұрын
​@@LivyuFPV What do you mean? Basically the FC will work if plugged into USB and all motors work. On batt, will get motor beeps but no flight controller power on or LEDs. Not really sure how to fix this other than following what Nate Payne said. Drone Mesh had a video on same issue showing that a diode can stop sending current but I've tested mine and they seem to be fine. I'm not an electrical engineer though ;)
@kandredfpv
@kandredfpv 4 жыл бұрын
@@LivyuFPV fair enough. I love the work you do for the community bro. You're a true hardware hacker! If you haven't already, maybe you can demonstrate an MCU replacement on one of those bad boards. IMO it's not too hard for a novice, and there are cheap STM32Fx chips on Ebay and Ali. I did mine with a regular hot air gun...haha.
@micciu
@micciu 11 ай бұрын
Hi, great tutorial, this content is gold for us pilot. May i know what type of alcohol did you use? Normal denaturated alcohol or isopropyl alcohol?thanks
@LivyuFPV
@LivyuFPV 11 ай бұрын
Isopropyl ftw :) and thanks!
@micciu
@micciu 11 ай бұрын
thank you for making this content...like and subscribe
@TheBlaznbowls
@TheBlaznbowls 4 жыл бұрын
So awesome. Where did you learn all this?
@brandonmoody3571
@brandonmoody3571 4 жыл бұрын
I have a few emax tiny hawk aio boards that are dead between just the initial beeps and one needs some esc repair how can I send them to you for you to use on your channel?
@CarbonGlassMan
@CarbonGlassMan 4 жыл бұрын
I had the same problem. 3.3v regulator got really hot. I replaced it and the new one got really hot. So I replaced the F4 mcu and the flight controller worked again.
@tyrian869
@tyrian869 2 жыл бұрын
Dam okay, I have the same thing happening with a JBF7 v2, I replaced the bad 3.3v regulator, and is outputting correct at the MCU, though I only get red light and it does not handshake with my PC just like yours did, I to have concluded bad MCU, Despite it warming up with normal temps, Is there a way to use another device like an Arduino to flash a bootloader? am I even saying this right? or a way to read from the MCU directly using another tool. to conclude it in fact is dead. as I'm not convinced lol
@DemoPwr
@DemoPwr 4 жыл бұрын
Do you the mobula7 FC to view, I would like to know the weak points on it. I have one that starts beeping and landing after 10-15 seconds of flight, even with new batteries... Thanks for sharing!
@toffpv
@toffpv 4 жыл бұрын
Thank for all your elec. vidéos like this :) I learn thank of you . you are the best at this in the youtube FPV world.
@illusionistsam
@illusionistsam 3 жыл бұрын
Hi brother you are doing a great job at repairing and teaching us alot can you make a video to fix osd when i conect my camera to FC It dosent show video only black screen with osd but works fine with my vtx with no osd i think something is burned it is small i cant trace it can you help us with that
@EvilDxtreme
@EvilDxtreme 4 жыл бұрын
Well done and good examples as always. That's great how you used alcohol to find the heated components. May be a silly question but Is it safe to do so on one you plan to repair fully? I'm a novice and wasn't sure if it would short another component?
@LivyuFPV
@LivyuFPV 4 жыл бұрын
alcohol is safe :P
@Asu01
@Asu01 4 жыл бұрын
Hi Livyu, this is a bit unrelated to the video but I just found something interesting I'd like you to take a look at and have some words. There's a video on KZbin that shows how to repair a "Bolt32" ESC (that's not even the right ESC). I'm not posting link for ethical reason but it's easy to find yourself. Basically, all the guy did was first supposedly test the ESC by powering up with 4 motor connected and no boot tones can be heard, then replace a single FET that was randomly chosen out of nowhere, which results in the ESC being able to initiate boot tones. Is that even possible? I'm pretty sure that's not how a failed ESC works. What's your thought on this?
@LivyuFPV
@LivyuFPV 4 жыл бұрын
Found one with a red PCB ESC... Indeed it is looking like a fake video... If you know how ESC's work you know that one bad MOSFET has nothing to do with a heating regulator or no beeps :P but hey :)
@Alex-ms1yd
@Alex-ms1yd 4 жыл бұрын
Thx for video! Is it possible to replace betaflight mcu with a fresh part and upload firmware? This will not work with kiss, but betaflight should be possible?
@LivyuFPV
@LivyuFPV 4 жыл бұрын
yes it is possible trough the betaflight configurator
@noisy_boi_fpv_3920
@noisy_boi_fpv_3920 4 жыл бұрын
Nice vid. I have iflight twing with bluetooth it took a tumble on field after clipping a branch nothing hard didnt damage quad ir props ni it will not allow vidieo feed to pass through it. Any ideas please. Just seems a shame
@LivyuFPV
@LivyuFPV 4 жыл бұрын
check the osd IC is properly connectect with all the pins... and check for missing parts around it (the osd IC is the I shaped, pins on 2 sides)
@Nicolas_dG
@Nicolas_dG 4 жыл бұрын
depending on how much the shipping costs i could send you some fc and vtx (especially one that seems to be stuck in PIT mode)
@Nicolas_dG
@Nicolas_dG 4 жыл бұрын
shipping from france btw
@LivyuFPV
@LivyuFPV 4 жыл бұрын
@@Nicolas_dG I live in Romania, should be ok I guess.
@scooterfpv8864
@scooterfpv8864 4 жыл бұрын
Good teachings 😎👍
@spitfeueranna
@spitfeueranna 4 жыл бұрын
Geez... wishing I had never gotten into this hobby... it's looking more like it's a big disaster of junk... or stuff you're about to smash into the ground and turn into junk...
@martinverbaas
@martinverbaas 4 жыл бұрын
I love this kind of stuff, love the alcohol trick. More....I need moooorrrreeee!
@fabianisensee3744
@fabianisensee3744 4 жыл бұрын
Good to have the commentary back! But 1x subscribe per video is enough. More is begging :-)
Diatone Mamba F405 MINI FC - REPAIR
16:33
Livyu FPV
Рет қаралды 6 М.
F4 Flight Controller Short Circuit - Can We Fix It
25:02
Mads Tech
Рет қаралды 6 М.
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН
小丑教训坏蛋 #小丑 #天使 #shorts
00:49
好人小丑
Рет қаралды 54 МЛН
Fixing the #1 Cause of Flight Controller Failure
12:30
Mr ShutterBug
Рет қаралды 24 М.
Broken USB Off Flight Controller Fix
11:14
Project Blue Falcon
Рет қаралды 50 М.
Airbot Typhoon32 4in1 ESC REPAIR
16:03
Livyu FPV
Рет қаралды 40 М.
FC REPAIR - RaceFlight Skitzo Edition
11:28
Livyu FPV
Рет қаралды 8 М.
The Most Common Mistake in Laptop Repairs The shorted mosfet myth - Testing mosfets
12:44
Tinyhawk II AIO Motherboard REPAIR
11:09
Livyu FPV
Рет қаралды 13 М.
Most FPV pilots need to watch this soldering tutorial
49:51
Joshua Bardwell
Рет қаралды 349 М.
How To Fix Flight Controller NOT POWERING ON // Repair Video
9:32
Drone Mesh (Drone Reviews)
Рет қаралды 74 М.