The Bearded Plumber° Remeha Tzerra Repair

[@musicoparaDios]

I would like to ask you a question, does this type of heater work the same way with a battery? On mine, the button on the left does not want to change from red to green, I don't know if it's because of the battery...

[@brendanfisher2528]

Great video! Keep them coming!

[@thebeardedheatingco]

Thanks for reaching out mate! Trying to do a weekly video! Live long & prosper! 🖖🏽

[@frietjesate6288]

Great video, very helpful. I have question. My Tzerra m28c Plus, used only for central heating, will not fire up anymore. I can hear a 'poof' on ignition, then fairly quick it restarts this process. It never gets to actual heating. Blinking red 3 times, which suggests ignition. Electrodes have been replaced. And it sound like it ignites at first go, but then there's no flame. Fan runs, exchaust pipes are free, condensation box is free. Someone suggested the heat exchanger is blocked on the bottom side. I've cleaned and vacuumed the top. How do i clean the bottom side? Can i just run water through it like you did in the video? Remeha says it's bad for the coating and voids warranty (which i don't have anyway because it's secondhand).

[@thebeardedheatingco]

Hi mate! I would suggest checking the gas co2% combustion on high and low... this might be out of calibration and also the ignition transformer could be faulty... and 1 last thing to check is to make sure u have good aarding/earthing Hope this helps! Live long & prosper! 🖖🏽

[@frietjesate6288]

@@thebeardedheatingco I have no device to measure these values unfortunately. Was hoping cleaning the heat exchanger would suffice before i had to call in a plumber. Wasn't really dirty on top though. The metal burner bed rather black / clogged though. Nowhere near original.

[@thebeardedheatingco]

@frietjesate6288 if ur not a qualified gas engineer u shouldn't go poking into a gas appliance... the results could be extremely dangerous

[@owsi2297]

Great video mate 👍

[@thebeardedheatingco]

Thanks a lot mate!!! Appreciate u taking the time to watch and comment! Live long & prosper mate! 🖖🏽

[@furkanaktalan1]

mostly it is only the gaskets of the excanger. cange the cartridge with 4 gaskets. You can save a lot of money

[@pietjespappie]

Those hydroblocks are the most expensive part of the Tzerra, aren't they? Some 500 bucks or so.. And it seems like they all fail after a couple of years. I have one of those too, dammit...

[@thebeardedheatingco]

Hi! Yes expensive, but easy to do especially when replacing the whole boiler can be tricky cos of the size and location! Live long & prosper! 🖖🏽

[@beyonddronedup8375]

Hello, i have a tzerra 28c. I'm trying to replace the treeway valve. I got it out fairly quickly. I thought it would be easy to instal the treeway valve and new motor. But the thing won't go in al the way in to the socket. I also cant secure it with the little pin bc it wont line up. Do you have a tip? 😅

[@willemgijs3803]

U tried using a lube haha

[@janseven7712]

Good repair ! 💪🏻🔧

[@thebeardedheatingco]

Thanks Jan! Appreciate it mate! Live long & prosper! 🖖🏽

[@stefanomohabir]

where do you buy those black wrenches? :)

[@thebeardedheatingco]

@@stefanomohabir hi! I got mine from Amazon, link below amzn.to/46uqjoR Hope this helps! Live long & prosper! 🖖🏽

[@stefanomohabir]

@@thebeardedheatingcothank you :)

[@eugenrogozea7758]

Hi! I had a couple of faults E.01.04 & H.03.54 on same Remeha. It tends to show these codes whenever changes from hot water to heating. Any suggestions?

[@reverend3712]

Hello, I've got the similiar situation to you. Did you manage to solve that problem??

[@eugenrogozea7758]

Yes. The heat exchanger and aluminium burner were clogged

[@reverend3712]

Thanks a lot