The Charlie Show /// Episode 336 /// Calibration Trouble Shooting

[@pandacrawler6x6]

A very usefull tutorial, thks for the Info Share! Just have up-grade the Wife RGT whit one Fusion Pro 1800kv and is Awesome, transforn the truck totally!!!

[@RuckusHuckusYT]

Thank you so much man this helped me calibrate my Hobbywing SE motor easily!!!

[@ilesk8964]

Hello. Friends! I have a question, can I take my hw fusion se 1200kv apart by removing the screws on the housing to replace the bearings if they break?

[@wadedavis9344]

I have a question. Accidentally hooked battery backwards on xr10 pro. Poped capacitor. Replaced and works fine. But doesn't seem to have full throttle. Is that fixable or trash it?

[@HOBBYWINGOfficial]

Would be worth resetting the ESC and triple checking the replacement power cap and the wiring. Typically all that needs to be done, is the power cap replacement, with a genuine Hobbywing Power Cap of course.

[@wadedavis9344]

What's the best way to reset esc. Don't see the option on my ota? Thank you for the reply. At full throttle light turns solid green. But no top end. Swapped each and car is back to speed

[@HOBBYWINGOfficial]

@@wadedavis9344 Under parameters, you can reset the profile of the ESC. Would be worth checking over the plugs. They can wear out over time, get dirty, and cause losses. Loose bullet plugs after a reverse connection are common. The plug can get hot and deform easily.

[@DaddyDaughterRC-sw2zb]

Question for you regarding fusion 1800 se. Motor was not running smoothly anymore so tried calibration by having motor removed from crawler, disconnected from esc, connected to battery and hold for 8 seconds till it flashes green. Normally goes through cycle etc and then turn off. Mine starts the shaft spinning after flashing green for about 5-7 seconds then stops, jerks then just starts rapidly flashing red and nothing else. Whats the problem?

[@HOBBYWINGOfficial]

You can Email [e-mail] for assistance. Thanks!

[@dougchesney5586]

Okay so I have a question as I use two of there’s motors on an MOA bully 2 with a radio link remote. When crawling sometimes my rear motor will lock up and it will move super fast and then just drag like it almost jolts forward when I’m in a slow crawl and then will lock up the rear motor would recalibrating them fix this?

[@HOBBYWINGOfficial]

Shoot us an email for support - [e-mail] Would be worth doing the Automatic Motor Pairing on each of the motors to let them "reset" their sensors.

[@sameersutar5203]

I bought a hobby wing fusion pro 2 in 1 but when i plugged the battery it worked for sometime then the button doesn’t light up and before that the motor was jittery so i just took out the battery as it was not turning off! NEED HELP !! What should i do and what can be the problem

[@HOBBYWINGOfficial]

Should be able to redo the Automatic Motor Pairing. If that's not it, send us an email - [e-mail]

[@LJSCOFIELD]

Unfortunately my calibration goes green once and then doesn’t do the forward or backwards calibration. Any advice?

[@HOBBYWINGOfficial]

Typically, when an ESC "won't" go through calibration, there is an output problem from the channel itself. Check the throttle channel output, "Visually" by using a servo to test the channel.

[@LJSCOFIELD]

@@HOBBYWINGOfficial love your work, but I now got another problem with my steering. Is there a way to centre or calibrate your servo?

[@maltesrc]

Please make a Trx-4m fusion

[@swadewatts4282]

Hi guys, love your channel, can you help, just watched your 336 episode, as my 10bl60 is playing up, for some reason I couldn't get the throttle (transmitter gt3c) to work, when I turn it on solid red led comes on then goes off, when I try to calibrate it after I turn it on while holding the set button until red led starts flashing and beeping the motor keeps moving/rocking very slightly (1 tooth) no green led I press the set button while in neutral the red led goes off as does the beep and motor stops moving, also tried your servo trick taking esc out of channel 2 and replacing it with the servo I still get nothing, can you help, Kind regards. Jason

[@HOBBYWINGOfficial]

Please send us an email for some direct support - [e-mail]. Sounds like you've got a channel output issue. Check out our "servo Test" video for some trouble shooting. kzbin.info/www/bejne/hIimmJWujK6jaJY

[@coolinthewoods]

I guess I'll pull my "bad" Fusion se off my shelf and try again.

[@hardworker2877]

Need Help : I Need a E SCOOTER ESC 9037.. and I have emailed every person I can find still no help I need a dual motor speed control...this is the Page to help someone help me with a link to buy..