The Easiest Way To Gain 100 Horsepower!

[@bodyshop5134]

Easiest way to gain 100 HP? only gain 47 HP. BOOM done.

[@ObediahWilson]

I'm not sure if the cost was mentioned but even the guy at the end was like another 75 to 100 hp added but if its 47 hp probably an expensive mod for low gains

[@Stellicopter]

Did I miss where a 50 HP gain suddenly turned into a 100 HP gain?

[@LeadDevelopAchieve]

im guessing the 75-100hp statement was reference to bone stock and since this car had an intake on it already and then gained 47rwhp with the headers that would put the crank hp gain right around the 75hp mark

[@Stellicopter]

@@LeadDevelopAchieve Even 28 WHP off an intake alone without tune would be a pretty far stretch. Throttlebody, intake, headers, and tune may get you close to a gain of 75, maybe 100 with head.

[@LeadDevelopAchieve]

@@Stellicopter if you read, or shall i say comprehended my previous comment I said crank HP not WHP, therefore the intake wouldnt need 28, more like 15. here let me do the math for you. 47whp(header gain)+ 15whp(theroetical intake gain)= 62whp/.84(whp to crank conversion) = 73.809 and so i say again "right AROUND the 75hp mark"

[@hb-ol9oc]

@@LeadDevelopAchieve You are right but far from the 100HP, and the title of the video was refering to the headers only, so @stellicopter is correct in his first question, it looks like a click bait to me.

[@hustle.dinero]

Click Bait

[@gilbertahsam643]

Your worker that was working on the 2020 2ss camaro. He didn't put any cover wrapping on the fenders to protect in from scratches from his belt or his tool's DANG that hurts a nice car.

[@Pboy7272]

05:55 "I'm just trying to..." that's shop talk for "get that camera out of my face" LOL That color is on point, love it. Whole vid is top notch, new sub.

[@Standyourground21]

The guy installing the headers has he ever heard of fender guards or that blue plastic wrap. The paint on camaro’s are so thin doesn’t take much to do damage. That’s my beef other then that he knows what he’s doing and installed them fine. 👍🏻👍🏻 460 torque is nice. Plus plus u fixed the volume when u test drive. LMR your the best. Next mod for him E85. Thumbs up for sure.

[@jd1029]

Agreed. I would be bent if I saw that happening. Just common courtesy to protect the paint.

[@Blown6thGen]

You could also see him starting to lose patience. Which is something you shouldn't do because everyone knows Headers are a PITA.

[@Fade2BlackSS]

I don't know why everyone is mad at the title. Technically he did gain around 100 more HP. The dyno measured 463whp which translates to around 550 to the crank. If y'all are "car guys" and don't know the difference between the two. Please do some research. The 6th gen SS come factory from stock at 455, I believe. So if you're going off crank HP, then yeah he's totally correct. 🤷🏾‍♂️

[@al151]

Problem with headers is that they will mess up your knock sensors. My advice is don’t cheap out on quality high wall thickness header.

[@ClaytonYatescarenthusiast]

Lt2 manifold and zr1 throttle body. Requires porting the inlet of the LT2 manifold and an adapter. But for 1,000 bucks in parts you can pick up 30-wheel

[@PatrickScottlxw]

Exactly the reason I like older cars like foxbodys

[@kimchappell9559]

A friend of mine who has a 2020 ten speed transmission and Texas speed headers and the LT2 intake and ZR1 Throttle body and E85 with slicks and stock rear exhaust system no cats. Turns 11.3. In the 1-4 mile was his best time. They used some one box to tune the E-85. I don’t remember who.2” headers.

[@BossAdams3]

I wouldn’t take my care here solely on the fact they don’t protect the cars paint. The little details take small shops to the next level

[@LateModelRacecraft]

thanks for tuning in. he doesn't work here anymore

[@joemeyers1016]

It's not the factory headers choking it's the factory cat pipes. The only way to compare apples to apples would of been to delete the cat pipes first then compare the Long tubes vs stock tri-y's.

[@MasterCarguy44-pk2dq]

Catts or no catts, you won't gain more than a few hp.. I worked in exhaust business and have background in flow dynamics. Catts just drop a little weight and add fumes. The huge curved 35°-65° air intake tube is a huge restriction. Figure out how to bring air in with less than a 30° bend in the tubing. Cut and add a custom naca duct at front leading edge of hood and air intake filter right there. Straight in. Put some fine mesh there. Like the little slit in the C6 Z06 hood or bumper on older 2009-14 12 Camaro SS.

[@joemeyers1016]

@@MasterCarguy44-pk2dq I said the cat pipes not the cats themselves. The entrance into the cats necks down under 2" on 6th gen Camaro exhaust.

[@nuffdoggiggey4103]

I have the same car just did a 0 to 87 with a land rover rover that rover got it but we was neck and neck I'm not sure if he had the 515 or 575 hp but my little 38,000 dollars hold out to the 96,000 to 115,000 cash cow . I was on my run flats that are losing grip if they even have any ..any suggestions on tires?

[@sabrom]

Sounds good at idle and wide open but that deceleration "Snap Crackle Pop"? could be a lil annoyed.

[@LateModelRacecraft]

The good news is the "burble" tune only works in manual mode on decel. So when you're cruising normally in Drive it doesn't do it.

[@Standyourground21]

@@LateModelRacecraft 717 fav giggle mod. Snap Crackle Pop

[@sabrom]

@@LateModelRacecraft "Niiice".

[@ttcookn8246]

@Late Model Racecraft- burble tune = fad only! I think it’s annoying BUT each to their own👍

[@kaiserschnitzel89]

A KZbinr made a clickbait video and you will be SHOCKED at what happened next

[@PD-oj6uy]

Can you improve a Chevy 3.6 Liter V6 HP with headers ?

[@cski12894]

It sounded fantastic and the power gain was incredible. But I am afraid I don't have a shop with a lift and all the tools and expertise needed to do it. I thought that you can simple add a cam for a stage 1 tune with an output of 515 hp and 491 hp.

[@leoreid5649]

Great. In Amarillo, just had speed engineering headers, exhaust, rotofab and tune installed on the 1le. This was a great reference for me. From 409/411 base on a dyno jet to 430/445. I left the factory suitcase muffler though, keep it kinda quite. Does that sound about right? Thanks guys, keep up the great work.

[@Tyee2]

He leaning all over that new car fender with no protection film on it. smh

[@jasonnellis3566]

Hello you guys are awesome I have a Silverado 5.3. when I add 1 7/8 texas speed long tubes and 2 hi flow cat. How much hp should I have. Also I have a flow master hi flow I place already on the 3rd 3" to the front of flow monster 40 series muffler dualed 2.5 left and right behind wheels. These are all my bolt on. Ported 80mm katech throttle body airaid spacer airaid Jr tube into factory box with k/n filter aw1 oil can pedal commander msd coils msd wires. I'm lookn to install stage 2cam a new ported and polished heads. Any suggestions let me know. Thnx

[@joshuawomack2515]

Do you guys know anyone working on unlocking the 2020 camaro 10 speed TCM ? To my understanding they are not yet able to be unlocked please shed some light on this

[@freshfowler1398]

Really love that y'all are the best at what you do!👍 Just wondering if something is wrong with Mike's ZR1??

[@alexmyz7568]

Love the way it pops through the gears music to my ears

[@nomansland3840]

Easiest way to put a smile on the face.

[@slightly.above.average]

Longtube headers + crossover + NO CATS + tune = 47 rwhp over stock Not everyone can go catless. Longtube headers on a stock engine make around 15 - 20 rwhp and cost $1,300-$2500+ The dollar to power ratio isn't worth it.

[@ricin82]

What would you do for the money out of curiosity? Deciding what to do with mine.

[@slightly.above.average]

@@ricin82 Get a forced induction kit from Boost District. Easily biggest bang for the buck. Stay on low boost for a bit until you have enough funds for other supporting mods such as an interchiller. Long tube headers would be on the list, but not 1st. Depends on your goals and budget.

[@MerkabaSS]

I have shadow metallic gray,and either your camera or whatever you waxed the car with is doing it justice. May I ask what did you do for your paint?

[@jaymelynnmcintyre8574]

Yeah I have the Grey metallic mist

[@kurtthomas4746]

HI, Unrelated to this car, but have you been able to UNLOCK ECM on C8 yet. Thanks.... love your videos

[@panero718]

Was the Corsa headers coated ?

[@JoseGarcia-sc4nv]

Only 50 hp gain what happened to the easy 100 hp gain ?

[@cammullis1852]

I feel like LMR and RACE proven motorsports should do a build off yall each get the same model of car with a set budget and see who makes the most power.. the rules/ judging Cleanest build/install Most hp/tq And effenancy/

[@markythunder]

What was the total cost of all the parts and labor to achieve 75 whp?

[@ICONBADGTA]

God that "POPPING" wet fart sound.... Nothing like the "RUMBLE" of flowmaster 40 series... To me anyways... And for some reason they sound best on stangs, why i dunno..

[@92IsaacYun]

What’s the exhaust he has on?

[@PhillyDee215]

Exhaust is a must mod regardless😉

[@J2A61]

I did a genV L83 swap in my third gen with a Texas speed stage 3 cam DOD delete springs upgraded the entire kit. How much spray is safe with no ring gap???

[@kal-elprime5678]

I hit 350hp in my V6 and can do more with little. SS for the V8 sound but other then that V6 got you.

[@maximo247]

With a heads cam, msd manifold , e85 trans tune would make a very fun car

[@hb-ol9oc]

Maybe then it gets to the +100 hp they claimn the title: +40 with the manifold +50 with the heads/cam.

[@puterg0d]

What is that jack stand in the rear for?

[@sammacintyre2583]

What kind of performance can you get out of these 10spd? I heard you say about unlocking it.

[@TBagr]

Did I miss the part where you got the 100 HP?

[@LateModelRacecraft]

Mr. Fereday mentioned in the video that with the couple mods this car has, this car is making almost 100 flywheel horsepower more than stock.

[@jmilz28]

Figure in 18% drivetrain loss for an auto. 440 at the tire is 536 at the flywheel. That's ~80hp bump at the flywheel over bone stock. Do the LT2 manifold and ZR1 TB the guy below mentioned, retune, and you get there pretty easy when looking at flywheel #s vs factory rating.

[@donbjorkland1386]

@@jmilz28 using the dyno numbers LMR has, 395 horse power base with the cold air intake and axle back calculated at 18% drivetrain loss (10 speed auto) = 466 hp only 11 crank horsepower more than the stock 455 SAE rating. With headers and no cats 440 + 18 %=519 horsepower net gain 53 HP. Or just take the raw dyno #s the car gained 45 RWHP with headers and no cats. Did any one notice if the dyno was set at SAE smoothing or STD smoothing?

[@watrousmark401]

The next mod? Go to school! Always invest in the driver before you start changing up a really good car. If you can't use the power you've wasted your money. Then he'll be ready for a cam and heads.

[@SSharpStuff]

Jesus I just need to pull the trigger on a full corsa setup already.

[@Only1jb._]

50 wheel, 100 crack. Use your brain

[@batman-telephoneman5479]

Exhaust pops make car sound as dunno the tune is bad.

[@Blakehenry11]

I would like to do this mod but I can't get past emissions with it here where I live.

[@joshuaavila8317]

I just got my 2ss so headers intake and exhaust will make 100 hp more?

[@edennard1]

You’ll need more than that to gain 100 bhp .

[@paulsugrue-e3e]

No protection on fienders ?

[@natanaelguadalupeaviles1550]

I heard the car is new so my question is how much longer should it wait to change spark plugs and cables? And is it sage to change ignition box or add more voltage to it? Nice mode. I'll do the same.

[@cski12894]

Does it even have spark plug wires? I thought there was a computer module at each plug for timing/firing regulation.

[@etdancer]

What Corsa muffler system is that? 🔥

[@danielfierro5694]

So, I'm guessing 100 HP @ the flywheel?

[@soylentgreen7074]

Didn’t know the guy from the carbonaro effect worked at LMR.

[@carloszura675]

😂

[@TorqueMachine]

Do 2016-2018s burble like that after headers/connection pipes? Or only 2019+

[@BamaBullyKamp]

Does the SS still keep the dual exhaust mode after adding an aftermarket exhaust?

[@ricin82]

Borla makes a system that keeps the NPP exhaust cutouts operational

[@merc2ss]

Stainless Works, Corsa, Borla do

[@sowhat424]

Best shop out there period. I'll say gain 20

[@carljackson6942]

I would not be working on my car no paint protection. That’s the first thing you do take care of of the customers car. I hope you read this comment

[@arcticvette6573]

Love the part where cameramen being with mechanic and he said he torqued spark plugs to 200 foot pds, lmao 🤣

[@MylesZ06]

Pds? Why not Lbs lol

[@MasterCarguy44-pk2dq]

You gotta be pretty dumb to believe a aftermarket CAI with the same curved tubing makes over 5 hp, let alone 20+ hp. X pipes add a few hp and long tubes about 15-18 whp. Bigger, shaved TB might add 4-5hp, ported stock mani is good for 12 hp and WAY cheaper than a MSD or Atomic AF. LT2 is good but not worth it either as it makes 2-4 hp more than a ported oem unit. You just cant crack 100 hp out of the LT1 FBO without adding heads or a cam and 93 fuel w/E. Then close to 100 hp.

[@rvchipster]

Any problems with check engine lights?

[@karldemaree5644]

I have a 2003 Vett that only has 30 thousand + miles on it what could you do to get a little more Hrs power out of it, this car is like brand new, you could eat off the engine bay and it's a six speed, could you give me some prices also? Love your videos.

[@mattlaw3600]

How about a 4th gen Z28 for bolt ons??

[@hortonj63]

2013 silverado 5.3 LMG. full LLT2 gpi VVT Cam kit, ported and polished heads tuned with headers, cold air intake and full exhaust. i feel like 311/328 at the wheel is a bit low. i know the 5.3 isnt a big monster power maker but does that seem right? Its on a 20" wheel with a 33" tire 3.42 gears. i feel it should make more around 350/360 wheel

[@texastootin1628]

Tires too big. Go down to an 18 or 17 with a smaller sidewall and a shorter gear. A 3.73 gear would be a lot better.

[@SilentKiller-kv8kg]

I love how that you can see Street speeds car up on the lift when they’re working on the front end of that Camaro

[@mileswoods2527]

where are you located an what city

[@Angel370z]

Question why replace those spark plug wires?

[@see7.Raymond]

A K&N drop in filter would do better then that intake 🗿

[@sniperlif3]

Where is the 100 horsepower gain? These are stock ~400 bhp, you showed 50 bhp gain which lines up with a normal intake/exhaust with a tune. The intake and exhaust stuff the customer had wasn't tuned, aka it did nothing in the "stock" dyno. I have a feeling that you guys didn't know the Gen 6 made more power than the Gen 5 Camaro. At least I hope, because otherwise this crew is horribly ignorant or lying if they think it made more than 50 over stock. Then you have the mechanics leaning on cars without protecting the car besides foam as a tool tray. Is this shop that cheap? First time I have seen a shop tune in track mode to tune as well. Every shop that specializes in Chevy products say it results in poor tuning because of the crap Chevy does in track mode, plus most owners (myself included) say it is horrible to drive in track mode (poor pedal response, horrible steering feel).

[@TheRealDarthVadar]

If off road pipes aren't legal in your state because of inspection move 🤣 headers off road pipes only way to go or one of those exhaust jobs you can open and close

[@Slowmo896]

Dang that dude freaking moves fast while working, lol..

[@LeadDevelopAchieve]

LMR can you share the Part number of the headers used?

[@jiovaniiniguez5595]

howd yall tune the TCM to get it to pop through the gears like that? I love that sound

[@PaulVisentine]

Would Corsa cat back exhaust sound appreciably better than a stock Chevy NPP exhaust?

[@srhatfield]

That torque should make any Mustang owner shake in their panties.

[@roadblock539]

i just subscribed.. where are you guys located?

[@LateModelRacecraft]

Houston, TX

[@ttcookn8246]

CJ has been working around ALDO to long 😀😀

[@stevejohnson9513]

Next, a cam

[@9MMike1121]

Is that a 2ss? Or just an ss?

[@barrygavin4452]

Cover the fenders !

[@kolbyhumbert2680]

What color is that SS?

[@Bmackins94]

Satin steel metallic

[@illmicman]

Interesting, at beginning of video you stated and showed HP was at 399. Chevy advertises SS come stock with 455HP. Somebodies lying..

[@edwingonzalez5610]

whp and crank hp

[@Zle_blacklightning]

This is a with a manual only gents calm down. With an auto not EVEN CLOSE!!

[@joshreynolds729]

Got to be a pain working on chevys there is no damn room, shit is cheap plastic and procedures don’t really make that much sense due to the limited space. Love the sounds and the motors the cars make even the brand but quality and intellectual thought needs to be done so the mechanic doesn’t need to struggle. Never used to be like this Chevy was number 1 for the longest in the old school days. Not saying they aren’t functional today or implying they aren’t good I just think it could be better from Chevy that’s all. And what’s up with that bubble pop? Is that a standard thing or did the customer request this in his tune?

[@isiahgomez6860]

Not a pain at all if you know what you are doing... Real mechanics don’t struggle

[@1BOSSman760]

isnt stock 455 ?? how is 465 a big gain?

[@robertobenitez2702]

Do you guys offer just burble tune? And is it remotely

[@LateModelRacecraft]

Unfortunately not. We do not offer remote tuning

[@matrox]

The crackle and pop sucks though.

[@richmcdowell]

Give it a Fereday Maggie

[@nickaa121212]

I’d be down with that car.

[@Jermaindupreee]

Didn’t Chevy say these have 455 HP stock????

[@justabush1028]

This is a 5th gen

[@Fade2BlackSS]

​​​​​​@@justabush1028s not. That's a 6th gen. You can tell by the taillights and the fact that it clearly has an LT engine. The 5th gens have the LS3 or L99 engines. (I have a 5th gen SS) But yeah, the 455hp is crank HP for these. All cars lose some power (around 15-20% of crank HP) to the wheels. So stock, 455hp at the crank, he was probably pushing around 381 to the wheels. That's why they kept saying it gained (wheel) Horsepower because Dynos measure how much power the car is actually putting out. At 463whp, he's probably around 550hp to the crank. Crank HP is basically just bragging rights. Lol. But technically he did make 100 more HP. 🤷🏾‍♂️

[@adamkrail6012]

You guys are the best! I’d love to just ride in a car y’all built!!

[@jblovell9065]

Gotta cam it up for sure

[@ronobjrII]

Done by lunch? Yeah right----LOL

[@1slow5point0]

So much easier than the Mustang.

[@ricktotz4078]

Chevrolet needs all the horsepower it can get to compete with the mustang

[@funnyman1972]

Next mod E85

[@thermionic8530]

I believe the customer would be very happy with that horsey-gain, I would be happy. It sounds excellent too. The other thing is you're not messing with the engine at all, just letting it breathe, removing the Covid mask!

[@devinfraser9795]

From Nova Scotia 🇨🇦👍👍

[@anthonybomicino3276]

FML. This makes 13 lb ft more than mine with a hot cam on E....

[@ClaytonYatescarenthusiast]

Would be interested if you raced you'd pull it hard

[@jmilz28]

@@ClaytonYatescarenthusiast Probably not, assuming similar weights. 460 ft lbs through the 10spd will hurt some feelings.

[@2929camaro]

PROTECT THE PAINT PLEASE.

[@MARTPERE]

I rather get NOS ...1000 bucks and drives stock when not used

[@nickiebuswell2991]

Best color!

[@anthonybrown200]

Didn’t make 100? And no headers and x pipe didn’t add 60-70hp to this car 😂

[@mikehall737]

Wow rhat amazing sontku fot 500 at the crank

[@youngestson6537]

Awesome 👌