I could listen to Lake all day long and get educated. Then, I could listen to his dad all day long with his racing stories.
@flexjay874 ай бұрын
Lake Speed Jr. is a national treasure for us DIY citizens, in regards to revealing the truth ! Science vs Speculation is His mantra :)
@DrivenWildOutdoors4 ай бұрын
Agreed
@rohankiwi4 ай бұрын
Global treasure actually!
@nm-qt2hb4 ай бұрын
I have been building and tuning engines since the early 80s. I always read and update my knowledge base on my industry. Or at least I thought so. I stumbled on the Lakes videos about a year ago. I quickly found out what I didn't know. Thanks for hosting Lake on the channel, you now have a new subscriber. Well done gentlemen.
@DrivenWildOutdoors4 ай бұрын
Thank you for subscribing
@amounifndАй бұрын
Good attitude to have. Some people are stubborn and don't want to change with the times. Humans have advanced so much further in the last few decades than they did the previous century.
@GNX1574 ай бұрын
In addition to Lake’s recommendations, I would suggest using “top tier” fuel at a fueling station that displays the top tier sticker or label at the pump. There’s a web site that has a searchable list of top tier gas station locations.
@NoName-tz5ji4 ай бұрын
Been doing that for decades and never had a fuel injection issue,97 ford 4.0 450k all original when sold.
@thetechlibrarian4 ай бұрын
Same people fight so hard about premium gas but it’s not just that it’s a quality fuel station with a high turnover. I have a car that specked for 87 and I don’t care what anybody says premium. It has a 13 to one compression ratio my wife’s car has an 11.5 compression ratiothat has 120,000 miles on it. It was 87 when it was new however it’s not a new engine anymore. It has carbon deposits carbon deposits effectively raise the compression ratio.
@BeefNEggs0574 ай бұрын
@@thetechlibrarian Sounds like the usual speculation. Not science.
@Davido504 ай бұрын
@@NoName-tz5ji Can't beat Ford Motor! 💯
@NoName-tz5ji4 ай бұрын
@@thetechlibrarian if you have enough carbon in your cylinders to raise compression you haven’t been using top tier fuel and/or quality fuel additives 😂
@pwatom224 ай бұрын
So use synthetic oil, change it every 5k or less and use complete fuel system cleaner every oil change eg chevron techron complete fuel system cleaner. The big unanswered question is.. what about oil weights. Car manufacturers trying to get better EPA figures are recommending lower viscosity 0w20 oils. Perhaps 5w30 or 5w40 would actually result in great protection with minimal impact on fuel economy? Please ask LSJ back or some other true expert to answer that. Thank you!
@blackhawkgamingtv65533 ай бұрын
According to another one of his videos, always use the manufacturer recommended oil weight, heavier oils can clog extremely small oil passages.
@danielk71113 ай бұрын
@@blackhawkgamingtv6553I don’t recall him being absolute on that. I own an engine that has no problem yet but it seems they all eventually have a rocker/lifter failure. The rockers’ needle bearings can eventually stop moving to disperse wear so it ultimately leads to the camshaft lobe being wiped. In that situation, where the actually viscosity, the layer boundary, is the first line of defense against metal to metal contact. Based on that, I think that the locality of failure has higher temperature that needs a higher HTHS centistoke value at 150° C. Looking at old school big blocks where Lake gave advice (yellowbullet forum a few years ago) on hydraulic lifters saying they saw good performance from 3.8-4.1 cSt at 150°, I think it at least may show a direction to lean toward over and away from the factory spec to address wear. Yes the passages are small (vvt) and also may cause a hundredths of second delay in actuation, but the benefits MAY outweigh the negatives. If it makes a racket under the hood on 0w-20 when cold and warm…and you say go to a 5w-30 and it is significantly better cold and hot, you may be onto something. Of course, it needs a good additive pack too in the event the oil is displaced from the part’s surface, resulting in metal to metal contact, as a safety net. That’s why the additives are there, a safety net. Also, in my experience, I don’t assemble engines with 0w. Startup, especially fully cold, is where most wear occurs. I’d like some more resistance to the oil flowing away from the journals and splash lubed rockers. Especially since I have start/stop.
@matthewsandifer26733 ай бұрын
B student 4lyfe
@PunisherOfDeath1013 ай бұрын
Choose weight based on climate. If it's hot, you can go heavy..if it's cold weather, you run the risk of friction and wear on parts with thick oil that don't get up to temperature
@dannyelregio3 ай бұрын
I own a 2009 Honda CRV. I live in Latin America. In the US, user's manual for this car calls for 0w20 only. However for the same engine, same model, same year, but for a vehicle purchased in Latin America, the user's manual calls for: 0w30, 0w40, 5w30, 5w40, 10w30, 10w40 and 15w40 😅 so, there're other factors such as regulations in play besides engine specs
@Papparratzi4 ай бұрын
I guess KZbin brought me here because Lake was on it. Great show
@DrivenWildOutdoors4 ай бұрын
Thank you for watching!
@usocrazy61334 ай бұрын
Lake Speed Jr. is an awesome man and is truly the GOAT of engine performance. Guys like me benefit greatly from his expertise.
@DrivenWildOutdoors4 ай бұрын
Agree!
@chriswoodward53684 ай бұрын
Wonderful video. Yes if you want to be an a student oil sampling is the way to go. As a former fleet manager every truck, we had got an oil sample at every oil change. It allowed us to keep tabs on engine health and comparison to the rest of the fleet. By switching to mobile Delvac one we went from 20,000 mile oil changes to 100,000 mile oil changes And filters every 25,000 miles I would never recommend this in a car. And before anybody says anything, our fleet averaged over 1,000,000 miles per engine overhaul, which is more than we got with conventional oil and 20,000 mile oil changes.
@captnjim44smith744 ай бұрын
Great report Chris, it validated what I have been saying about synthetic and oil change cycles. For over the road truckers, a savings per truck adds up to profits !
@mason73003 ай бұрын
I do oil samples as well. And it gives me confidence to do 10000 miles on a change. Oil checked good as new. I could go further but I’m ok with the 10000k miles. It does depend on use and vehicle so an analysis would let you know where you are with your specific vehicle and use. Some instances will not make 10000 before breakdown. And your 100000 intervals are amazing but is probably from a lot of proper operations and procedures.
@captnjim44smith743 ай бұрын
Yes, I agree with oil sampling, but years ago, petroleum oil was what was being tested. Today, with pure synthetic oil, results should not be viewed as they were. I saw a technical paper saying synthetic doesn’t wear out, it just gets dirty and contaminants, so I change oil at 24,000 miles like some trucking companies !
@mason73003 ай бұрын
@@captnjim44smith74the thing that concerns me is the contamination as well. I think that is what wears chains and guides. so I do get the results on contamination but it is low when I change it. Even though the oil checks great. but it is there compared to new oil. Some have the oil polishing equipment like ships and trains and the oil lasts many years. I’ve seen it in vehicles. Cheaper to change oil.
@captnjim44smith743 ай бұрын
@@mason7300 I disagree. It’s not cheap to change oil that is nearly new just because of a small amount of contaminate. What is sensible. I have driven multiple vehicles since the 1970s with no discernible wear, no smoke before I traded in 170-200k miles. I’m happy to continue my way.
@gregbellinger57652 ай бұрын
Very nicely done as the moderator. Ask the right questions to the right guy at the right time. Excellent summary. GB
@DrivenWildOutdoors2 ай бұрын
@@gregbellinger5765 thank you for watching
@faxbullog8361Ай бұрын
I’m not a car guy- just searched on oil. I can’t turn this off. I am a big fan of listening to an authority on any subject
@DrivenWildOutdoorsАй бұрын
@@faxbullog8361 awesome! Lake speed jr is an expert for sure. Thanks for watching
@johnbutera58054 ай бұрын
I have a feeling that Smokey Yunick was a tribologist before there even WAS such a thing!! Anyway, I know that he was VERY interested in oil, oil pressure, friction, etc. and also always in touch with the oil companies. He also commonly sent out for oil analysis... he knew about it because it was common in aviation.
@TakeDeadAim4 ай бұрын
When I bought my new 2020 GMC Sierra with the "Mini Max" 3.0l Duramax, the salesman said "Oh, bring it back when the OLM gets down to under 30% and you'll be fine!lol! Nope. 700 miles and dumped the factory fill and then 5k ever since. 82k trouble free miles so far....and great UOA's from Blackstone using nothing but the spec oil.
@DrivenWildOutdoors4 ай бұрын
👍 and it should last a long time! Thanks for watching
@Ram142504 ай бұрын
The way I'd do it too! Honda Element owner: original engine/ and / trans: 364,000 miles and going strong!
@Davido504 ай бұрын
@@Ram14250 Same here! 07 F150 4wd. 344k mis & running great! All orig except for alternator.💯 Also have newer 23 F150 Tremor 4wd. Can't beat Ford trucks.
@redlywaxer4 ай бұрын
I though I knew a good bit about lubricants, but the Oil Geek has taught me a lot of cool stuff about oil and lubricant do's and don'ts. He actually tests this stuff and shows the results, then explains things in a way that make great, practical sense!
@DrivenWildOutdoors4 ай бұрын
Thank you for watching. He is very smart for sure.
@GrayBattleAxe4 ай бұрын
Great show. I have watched M.O.Geek shows etc. This show helped me tremendously!!! I am B student working on being valedictorian!
@DrivenWildOutdoors4 ай бұрын
Awesome! Yes Lake is the real deal
@gregbellinger57652 ай бұрын
More friction can make a surface smoother. Mr. Speed has a comprehensive view of everything involved with lubrication. fun to listen to. Thanks. GB
@brianpmiller_bpmxphoto4 ай бұрын
Great interview. I greatly enjoy Lake's channel, a wealth of great information.
@DrivenWildOutdoors4 ай бұрын
Thank you for watching
@proudamerican55184 ай бұрын
99% of these automotive engines do not have cylinder sleeves, they are just cylinders within the engine block. They are not removable sleeves like you would find in certain heavy truck and equipment diesel engines. Also, using the accelerator to the floor method is not to purge and engine, it is to prime the engine’s oil system by developing oil pressure at lower rpm with minimal force on the rotating assembly prior to the actual start. Great choice bringing Lake on the show, I really liked the interview.
@DrivenWildOutdoors4 ай бұрын
Thank you for watching
@mandytuning4 ай бұрын
Cylinder Liners
@rickcoleman89034 ай бұрын
To purge air from the oil gallery
@billm62944 ай бұрын
Most engines today are aluminum block with cast in iron sleeves. Not removable, but sleeves nonetheless.
@stevesmith7563 ай бұрын
@@billm6294what about the engines that have plating like Nikasil. All motorcycles aluminum cylinders are plated. I would think high performance cars would be too
@haac48254 ай бұрын
Love this. Never thought much about oil. But now learning soo much and making sure I get the correct oil brand, filter and weight.
@DrivenWildOutdoors4 ай бұрын
Great! Thank you for watching our channel
@davebarron59392 ай бұрын
Always enjoy anything Lake Speed brings to the table, huge knowledge base. Thanks.
@davidsteckley88464 ай бұрын
I run Mobil 1 0/40 in everything. Never had a motor issue. I use Redline SP1 fuel cleaner
@ceecee24852 ай бұрын
Great video. Learned a lot. Thanks!
@W.Khairi4 ай бұрын
A lot of knowledge, Great episode, Thanks a lot for sharing.
@DrivenWildOutdoors4 ай бұрын
Thank you for watching
@travispeoples4 ай бұрын
Don't neglect the other fluids either. Differentials, transfer case, transmission, brake fluid, power steering fluid...
@DrivenWildOutdoors4 ай бұрын
Good advice. Thank you
@daleyaeger2984 ай бұрын
I suck out and replace as much brake fluid from the master cylinder and replace it with fresh fluid every year. The same thing should be done with power steering fluid. And the addition of Amsoil Coolant Boost works well for my vehicles. These are things only a DIYer would do.
@bobmasters16784 ай бұрын
This is great! I really learned a lot.
@DrivenWildOutdoors4 ай бұрын
Awesome! Thank you for watching!
@crisprtalk69634 ай бұрын
Oil is the only thing that keeps your engine from destroying itself. It better be good.
@budblack35884 ай бұрын
I have a Tacoma with the filter on top and I prefill my filter even if the filter is upside down, you just need to be quick.
@BeefNEggs0574 ай бұрын
Lol. Freeze it 😂
@budblack35884 ай бұрын
@@BeefNEggs057 I didn't think of that!😄
@kevinr.98963 ай бұрын
Bullshit
@ngrinshift43834 ай бұрын
My vehicles manufacturer specifies an ACEA SP 0w30 rated oil. Not an easy oil to find. I have discovered ACEA c2/c3 oil meets the same basic emission requirements. I know the minimum HTHS are different for each, lower for c2. Since my engine is a performance engine, and I don't care as much for emissions systems like the catalyst longevity as I do for wear protection, I lean tward using a higher HTHS rated oil. Since the ACEA c1/c2 oils have lower SAPS, to also help with emissions systems longevity virus higher ash content found in ACEA A5/A3 oil that helps protect the valve seats instead, I go with a 0w40 ACEA A3 oil POE/PAO oil. Eventually, I'll have a catless downpipe installed anyway.
@janekbrat4 ай бұрын
Amsoil
@jerryavlon47804 ай бұрын
Enjoyed the interview. Good info.
@DrivenWildOutdoors4 ай бұрын
Thank you for watching. Lake Speed Jr is a wealth of knowledge
@maxhorner24094 ай бұрын
I would definitely be interested in that other can of worms😂😂 at least Lakes opinions on filters.
@DrivenWildOutdoors4 ай бұрын
We will try to make that happen.
@francoisverdoes85522 ай бұрын
Thank you sir
@donreinke58634 ай бұрын
I was at a garage sale a couple weeks ago and there were two CANS of Conoco 10W30 with API rating SF, I suspect it was late 70s-early 80s. While I wouldnt put it in an engine, it does have one superiority to any modern oil...zinc content, an important additive with flat tappet engines which were common in many vehicles until around 1994. I dont give a rats behind about potential damage to emission systems, Im NO tree hugger. I check out these channels mainly for others opinions rather than advice as I am starting my 53rd year in automotive repair, and Ive seen, heard or both mostly everything..
@bobb99224 ай бұрын
lake has a video about using OLD never used oil watch it - you would never use any old/new oil after seeing.
@michaelmilot94154 ай бұрын
Great info. Thank you!
@robb150334 ай бұрын
I commute highway miles, 30k miles a year. I choose intervals of 10k miles per change using Mobil1 EP 5w-30 oil and filter. No problems.
@Jasiel.954 ай бұрын
Get the oil analyzed.
@robb150334 ай бұрын
@Jasiel.95 I want to, it's on my mind now. I have a 1.8l Toyota with massive amounts of highway miles. If your going to go 10k mile intervals, best to use "20k mile oil and filter"
@bmwlane88342 ай бұрын
I also drive a lot of long highway miles. I drove my BMW 530i 400,000 miles and I changed oil at 15,000 intervals. The guy I sold it to is still driving it.
@danramirez42903 ай бұрын
Awesome discourse! I learned so much - thx u.
@saulgoodman1244 ай бұрын
thanks mate,, really good
@DrivenWildOutdoors4 ай бұрын
Thanks for watching
@cmhwilderАй бұрын
Great stuff.
@captnjim44smith744 ай бұрын
My experience with Mobil One goes back to the 1970s. I read a column in Motor Trend of a hundred thousand miles test that convinced me, so I have had great experience since then. True synthetic oil doesn’t wear out like petroleum oil.
@donreinke58634 ай бұрын
It just gets contaminated. So I still change it at 3000-5000 miles.
@captnjim44smith744 ай бұрын
@@donreinke5863 yes, that’s what a filter is for ! I change the filter at eight thousand miles like over the road truckers, but I don’t throw out good oil for 24,000 miles !
@donreinke58634 ай бұрын
@@captnjim44smith74 I wouldnt let oil go half that long even in a diesel. 3000-5000 MAX with synthetic oil in a gasoline engine.
@captnjim44smith744 ай бұрын
@@donreinke5863 I did research on synthetic oil, and the technical paper said petroleum oil has different strands of molecule lengths, and the short ones wear out first. Longest ones last longer. Synthetic oil doesn’t wear out, it just gets dirty, so why throw out good oil ? Use filters. It will get contaminated by corrosive material.
@donreinke58634 ай бұрын
@@captnjim44smith74 I dont trust any oil to last over 5000 miles in gasoline engines and still provide good lubrication. No matter what anyone says. Im not cheap enough to risk engine damage for a few quarts of oil In 52 years of doing automotive repair Ive torn apart too many engines in which oil had turned to sludge from thermal breakdown. one of them I even scooped "oil" out of the pan by hand. It had spun not only rod bearings, but mains as well Another had so much sludge under the valve covers that they each weighed several POUNDS more than they did when finally cleaned, however that one still ran. You didnt convince me.
@davebest63694 ай бұрын
Outstanding video, lots of good information. Thank you. I've got questions about Amzoil, which seems to be the 3rd rail in the oil discussion. No one wants to explain why they say their oil is made in a lab and not from crude oil. Really hesitate to buy oil from the truck of someone's car.
@davebest63694 ай бұрын
Another interesting thing is that since every Amzoil dealer has their own website, they've polluted the internet so badly that you can't find any good independent oil analysis on motor oils. And when you do, it's an Amzoil site talking about some ball bearing test. As a friend said, when he's got ball bearing running around his motor, he'll consider buying Amzoil.
@jeffreyb14514 ай бұрын
No one says Amsoil is made in a lab. Everyone knows they buy their base oil from Mobil/Shell/Phillips and blend in their additives also bought from someone. That's it. They are a blender
@daleyaeger2984 ай бұрын
@@jeffreyb1451 I've gone through the Amsoil production facility in Superior, WI. There are different groups of base lubricants. While the original product may have come from the ground, the hydrocarbons of the Group 4 chemicals are truly manufactured and behave much differently than petroleum-based motor oil. Upon arrival at the plant, a sample is analyzed by their chemists to see if it meets the required specifications. If it doesn't the tanker or freight car is rejected. The manner in which the base chemicals and the additives are blended together helps establish the proprietary nature of the oil and the properties of the oil sold to the public through a dealer network.
@kc5104 ай бұрын
So sick of the “yOu ThInK yOu KnOw MoRe ThAn OEM eNgInEer?” Crowd.
@DrivenWildOutdoors4 ай бұрын
Ask those engineers at what mileage they change their oil.
@thetechlibrarian4 ай бұрын
22:17 I don’t know where people think that Brand New unfiltered oil is bad when the oil filter goes into bypass mode on a regular basis with used oil.
@aldifortuner2784 ай бұрын
Just list 5 top brand that you recomment sir. Thanks
@OldsmobileCutlassSupremeConver4 ай бұрын
Can you do a video on a oil accumulator. Would one help a 5.3L 3 valve from coming apart?
@jamesharris86524 ай бұрын
It just makes seens you should add oil in the filter. I know when you build a Buich engine you have to pack the pump to create a vacume to get the oil to pick it up out of the pan.
@djcooper93304 ай бұрын
I recently found your channel and find your oil info to be excellent. Thanks. Would you consider doing a vid on how much temperature oil can take before starting to break down? I have a Kohler twin air cooled engine in my lawn mower and it runs extremely hot. Other Kohler owners have also become concerned about this. Kohler even took notice and now sells an add on oil cooler. Although its small, expensive and likely does nothing. My machine runs fine but a couple years back I used a laser heat gun on the oil filter and couldn't believe it was reading 155c or over 310f after mowing. I installed a temp gauge to be sure and put on a large oil cooler made for a motorcycle. No change at all and oil still 155c. I change the oil and filter yearly, use syn 10w40 oil and clean the engine cooling fins. But it always runs that high temp. Thanks again and keep up the work.
@alexcohcoaching3 ай бұрын
Hi Lake, big fan of yours. Hopefully you’ll have time to answer my question. Got a BMW 650i 2007. I moved to a very hot climate(30+ and often 40+) 4-5 months in a year, and rest above 20. It’s very hilly as well and I drive my car hard after I warm it up. Been using 5w40 and no issues apart from oil temps being around 110 degrees to 112 degrees. The oil in question is Liqui moly 5w40 leichtlauf high tech. Liqui moly state it’s ok until 138 degree oil temp and safe to drive, but I’ve been thinking is it worth switching to a 5w50 or 10w60 oil while I’m here? No 10w60 oil have the LL-01 that my engine requires. Thanks for your help in advance.
@Johnnyscarcarereviews3 ай бұрын
Fantastic podcast
@frankc11744 ай бұрын
And my Amazon subscription to Chevron complete fuel system cleaner has been created.
@charlesaloha92324 ай бұрын
Do you think the 3.5L turbo engines in the new tundra are failing because of 10k mile oil changes? Perhaps if they had their first oil change at 500-1000 and again at 2500, then every 5000 miles, the main and rod bearings wouldn't start failing around 25k-80k miles
@DrivenWildOutdoors4 ай бұрын
I do not know the reason. They have been very quiet about the causes. I would think that a short term failure at 35 or even 8000 miles is due to something else however, I could be wrong. I was suspect something related to thermodynamics.
@albertpeugh93673 ай бұрын
You mention oil advertising. When I was in high school there was a late night TV commercial where they ran a normal car (normally a Honda Accord or similar) around a track stock, drain it, add the Wonder Oil (mystery oil) and run it around again. After 10 laps they’d poke holes in the drain pan and let all the oil drain out, supposedly, and run it around the track with only the residue of their Wonder Oil left in the engine and the car would just go, and go, and go……. We called it ‘Wonder Oil’ because we wondered why the heck people believed it. Then caught a lot of grief because people are gullable.
@davewallace90484 ай бұрын
I would recommend using the best oil you possibly can in your motor.. Companies that advertise full synthetic are allowed to do so with only 25% of that oil actually being synthetic. Amsoil for instance, is 100% fully synthetic oil.. Just wondering, why lake has not tested Amsoil signature yet? I believe it’s the best oil on the planet.. Smaller companies I rather deal with any day over the super large companies. The quality control is much better.
@mrtdiver3 ай бұрын
He used Pennzoil Ultra Syn in his daughter's car. Yeah I'm with you, but that is expensive oil where I can probably change oil twice at the same cost as Amsoil.
@jamescaron64654 ай бұрын
On the very first day of my physics 101 class, my professor got up didn’t even introduce himself and said this “do you want your nuclear reactor designed by the guy with a C average?“ I don’t even remember his name to be honest, but I remember that and it’s stuck with me, from that moment forward, I dedicated myself to never being the guy with a C average
@DrivenWildOutdoors4 ай бұрын
Great point, never bad advice to your best! Thank you for watching
@jamescaron64654 ай бұрын
@@DrivenWildOutdoors that was in 1979. Stuck with me ever since. If you want the best for yourself and your car. Do your due diligence.
@cmongimme4 ай бұрын
Huge Amsoil fan ...what are your thoughts on engine flush with oil changes?? Thanks dan
@daleyaeger2984 ай бұрын
I have been using Amsoil Engine Flush for years. Since Amsoil's 100% synthetic keeps the engines so clean, I tend to use less than the recommended amount before an oil change. The fear in using any flush in a dirty engine is the possibility that dislodged sludge could actually clog an orifice and therefore do more damage than good.
@frederickwoodard95514 ай бұрын
Mine is a port fuel injection/multiport fuel injection (PFI/MFI). Mine is 15-years old. 🙂
@cdburlockАй бұрын
Why do some videos have transcripts, others none ? This one has chapters , nice.
@Truckshack4 ай бұрын
You said that turbocharged engines have brass bearings, and have a break in time. If you change to a upgraded bigger single turbo, or a compound setup. Should you change the oil after what mileage? I'm talking about diesel pickups.
@rickss694 ай бұрын
Please point to any study or lab test that answers the question of what is the optimal ppm of ZDDP in oil.
@lonniebeal60323 ай бұрын
Search Amsoil or Pennzoil, which wins Championship? Let's find out! Under the more tab he has a link to oil analysis results for many oils.
@OldsmobileCutlassSupremeConver4 ай бұрын
And Check, clean or replace the oil screen on the turbo.
@wisetow104 ай бұрын
So what’s the best??? If I just go to my local parts store what should I get for the best protection???
@kevinr.98963 ай бұрын
Penzoil ultra platinum
@alexk72864 ай бұрын
🛢⛽️ good show (science) facts over friction 👍
@edwardmcgee54653 ай бұрын
very good video!!
@DrivenWildOutdoors3 ай бұрын
Thank you for watching
@mattsmith682825 күн бұрын
i'm 100% fine with being a diligent "B" student.
@mastercricket76264 ай бұрын
Ha ha so to all them ppl saying im a waste changing my oil every 1-3k miles depending on my driving ( its in a 91 mazda miata , boared 30 thou over with forged pistons and rods "pistons and rings from supertech" king race bearings billet oil pump , fluid damper , port n polish head , custom intake , oversized TB , and a 4849g pushing 34psi .. prolly missing a few other things that would contribute aswell but yeah , that alone is why i change my oil so often ...) o and i daily this car , fully legal were i live ,on standalone with a hood dump 😅... .. lake is a god when it comes to engines ... peace and love all keep it rad stay safe and build on l8z... ps my break in i used a conventional crude oil (not syn or anything as thats what machine shop had recommended) i did a start to op temp , then shut down and changed it then ran it 300 miles and changed it then whent to 1000 miles and changed it to full synthetic and have been run that since and its still alive round 20k miles later .. o yeah and i built this engine myself in my bedroom (ask the wife she was pissed lol) .. and all my knowledge came from 1 i have 2 older brothers that do nothing but engines (mechanics) there whole lives and 2 the rad knowledge that ppl like lake have shared with us diy guys ... anyways , sorry all my ADHD made me write a story .. my bad .. much love and respect to all and keep having fun
@scottpearce74664 ай бұрын
Best oil filter? I use Mobil 1 oil & filter every 5k but i hear Amsoil with WIX filter is best.
@kevinr.98963 ай бұрын
Fram ultra synthetic
@nikkoBcoolАй бұрын
Wix gold
@scottymoondogjakubin47664 ай бұрын
I had to question AMSOIL stating it is %100 synthetic ! One video i seen stated even the additives are also %100 synthetic ? Who makes the %100 synthetic oil additives ? AMSOIL ?
@DrivenWildOutdoors4 ай бұрын
I will check on this for you
@scottymoondogjakubin47664 ай бұрын
Thanks@@DrivenWildOutdoors
@PSA784 ай бұрын
I would say that it's rare to use additives that's not made synthetic, Amsoil knows how to market the h*ll out of things. 😆 All oil mfg buy the components from a handful of companies that makes either additives or base oils, like mentioned in this video.
@GrandePunto8V4 ай бұрын
Why everyone suddenly desperately "needs" 100% synthetic oil? Are blends etc. "bad" (like useless)?
@oneninerniner34274 ай бұрын
Synthetic lubricants can't be beat, well maybe just one way, price. But otherwise synthetics kick conventional & blended or semi synthetics oils butt. Also there are no rules or anything that says how much synthetic needs to be in a semi synthetic. I've heard many are like 15% or even much less synthetic so, just use your full or 100% synthetics and don't look back IMHO. I believe AMSOIL gets their additives from Lubrizol, at least they used to. Premium synthetic molecules like PAOs are polar neutral so they don't attack oxygen which when combined with the byproducts of combustion, fuel, moisture turn acidic & break down into varnish and sludge. Along with other positives like thermal stability, low volatility and the ability to clean and keep engine intervals clean.
@Noksus2 ай бұрын
My engine oil smells really badly of gasoline. I suspect that it is because of short trips that don't get the engine hot enough and lots of cold starts in the winter. I just changed my oil about 1k miles and one month ago and it still smells. Not all of the old oil comes out so that is still contaminating it, I guess. I don't think my driving since the oil change has caused more gasoline contamination because I have tried my best to let it warm up and it's summer right now. Could also be I have a clogged up injector. I probably should do another oil change before 6 months to get rid of the contaminated oil...
@daleyaeger2984 ай бұрын
Just a quick note. I had a car that went 170,000 miles without an oil change. I used Amsoil Signature Series 100% synthetic, the Amsoil spin-on filter, an Amsoil By-Pass filter combined with an annual oil analysis. After 9 1/2 years, the test ended when the new owned of the vehicle totaled the car.
@DrivenWildOutdoors4 ай бұрын
Wow, that was a lot of miles
@daleyaeger2984 ай бұрын
@@DrivenWildOutdoors The best oil combined with the best filtration backed up with oil analysis can blow our mind on how far we might go on a single oil change. However, every vehicle, driving condition and engine design will give different results. Oil analysis recommended an oil change in my Tacoma after only 30,000 miles.
@NoName-tz5ji4 ай бұрын
The bypass filter was the game changer.
@daleyaeger2984 ай бұрын
@@NoName-tz5ji Absolutely, true! The by-pass filter takes 10% of the oil passing for filtration and makes it analytically clean, filtering to less than 1 micron. Filter changes provide fresh oil and ultimately the TBN (total base number) moves toward the acid side, and the oil has to be changed.
@scottpearce74664 ай бұрын
WHY?
@nikkoalpha24 ай бұрын
For owners of new cars, can these oil samples be used if issues under warranty arise and manufacturers refuse coverage.
@DrivenWildOutdoors4 ай бұрын
Good question. I don’t see why not.
@tooththrhr4 ай бұрын
In the winter i use 20w 50 In thr summer i use 0w-20 My car has 15,000 miles and ZERO PROBLEMS
@brucebrowne50224 ай бұрын
🤣
@steverugerguy96062 ай бұрын
Lol
@TheJai2784 ай бұрын
Is Mobil 1 truck and suv Any good don’t see any videos on it
@MrRmeadows4 ай бұрын
I have some STP Fuel Injector Cleaner that isn't PEA based. Should I throw it out? My engine port injected not direct.
@MrRmeadows4 ай бұрын
Been a couple years since last time I put any STP in. Not sure how much to use. The bottle says it good for up to 28 Gallons. My tank is only 13-14 gallons. Should I use only 1/2 bottle or full bottle? I planning on checking the fuel trim before and after treatment. Is that valid test? My trim is within a few percent at idle. But is like adding 17% at 2,000 RPM. Does that raise any red flags?
@TheBlibo4 ай бұрын
Hi from the uk This ain't rocket science , I might disagree rockets are simple as Newton put it to every action there is an equal and opposite reaction. I would speculate that tribology is a bit more complex, Keep up th good work
@DrivenWildOutdoors4 ай бұрын
Thank you for watching
@paulnewton9434 ай бұрын
Doesnt changing earlier help the environment long-term. That is what isnt rocket science. Thanks guys. What i would like is transmission oils covered
@GunMuse4 ай бұрын
Valvoline clean and restore, VS royal purple which is better and why?
@kevinr.98963 ай бұрын
Penzoil ultra plat
@ralfrufus65732 ай бұрын
What do you think about 2 stroke oil in a Diesel?
@junzhang20874 ай бұрын
Just change with any SAE certified oil ever 3000 miles. Change the oil filter every other oil change so reduce the initial oil starvation.
@jamesharris86524 ай бұрын
I us Amsoil 2 and I go 25,000 on my cars using Signature Series.
@daleyaeger2984 ай бұрын
The Signature Series is the top-of-the-line product from Amsoil. And while their other very capable oils are less expensive, I just can't see myself buying "de-engineered" oil to save some money. I am a true "cheap skate" - but not when it comes to engine oil . . . . I have saved a lot of money over the years. I remain a DIYer.
@kevinr.98963 ай бұрын
That it extremely stupid of you
@hellohello85564 ай бұрын
I've got a question that I would appreciate a answer to. I've got a 2004 Kia Pregio 2.7 L Diesel van and if a 5w 40 oil does a better job than a 15w 40 why is 15w 40 still recommended for my diesel and a 5w 40 not recommended for my vehicle?
@jeffsmith20222 ай бұрын
Change your oil sooner than later...22,000 miles on my 19' Rav 4, 5 oil changes...
@GNX1574 ай бұрын
21:35 Purging? You’re not purging anything. What you describe is what can be called “clear flood mode”. It causes the engine to crank over but the fuel injection system is supposed to withhold fuel by not pulsing the injectors, indirectly causing the engine to not start, unless it actually was flooded and it may sputter to life. The alternate purpose being to get the engine to build oil pressure (thus filling the oil filter, NOT purging it out) without combustion loads on the bearings of the crankshaft and con rod bearings.
@DrivenWildOutdoors4 ай бұрын
Yes, I know the actual term, I just refer to it as purge for the oil aspect. Thanks for watching
@bigdaddymak14394 ай бұрын
Why are the oil manufacturers selling longer OCI also??? I've been doing longer intervals since the late 90s. The problem with today's vehicle owner is they never check their oil! Everyone of these modern engines consumes oil to get fuel mileage. I keep my vehicles topped off and have had no issues with longer drain intervals
@lonniebeal60323 ай бұрын
I was shocked by 10k mile or one year OCI from Toyota when a coworker bought a new one. But they were using full synthetics, and I know with a good motor that oil will be fine.
@FHollis-gw4cc4 ай бұрын
I have a question that I have never gotten a reasonable answer to, so I'll ask it here. We all have a "full flow filter" (oil) on our engines. Now, I have a problem believing that, assuming let's say 10-30 oil, at cold engine startup, at an ambient temp of 10F, all the oil is passed through my oil filter and not the bypass. Am I correct? How much oil (in GPM or any other measure) can pass through a factory (you pick it, Chrysler, Ford or GM) oil filter at the various temps that it is subject to? I'll bet I'm not the only one here that would like an answer to that.
@Craig-l2l4 ай бұрын
I forgot ask question about my 07 impala LS must follow gm manuel.it said must require full synthetic,follow every 5 k miles for oil changes.must do that ???????.
@robertbarr63884 ай бұрын
Hi Lake, I have a direct question for you, I run the bmw n47 2.0Litre diesel and sulphated ash(is that the zddp) at 800ppm, how high can I go before I start damage to DPF ceramic matrix and cat. Because I have the same issue with my Toyota MR2 Mk3 as it has cats in the headers. I would like your thoughts please.
@Chris-ut5ih3 ай бұрын
Should I use a fuel additive before or after an oil change or does it matter?
@lonniebeal60323 ай бұрын
I use Marvel Mystery Oil in the fuel and crankcase. Projectfarms proved it does what it says it will do.
@sierraecho8844 ай бұрын
My whole family is racist. My dad was a racist and his dad was too. I too like to race cars.
@BeefNEggs0574 ай бұрын
😂
@404aladdin94 ай бұрын
My car takes a synthetic blend 5W-20 can I run full synthetic without damaging anything
@DrivenWildOutdoors4 ай бұрын
I would follow up with a dealership and ask them that question for warranty purposes. However, I switch from a synthetic blend to full synthetic Motorcraft and the service manager at my dealership said it would not affect the warranty . But I suggest you do your own research.
@LA_Commander4 ай бұрын
Synthetic blend is the bare minimum to use under warranty. You can always step up to full synthetic any time. Just use the correct viscosity.
@ralfrufus65732 ай бұрын
@21:48 What does "purge an engine" means?
@ramonahumada44 ай бұрын
Thanks a lot for the info! Thanks to oil geek I’m changing the oil on both my Broncos every 3 k or 6 months! My question is, and I know what the answer is, but is it ok to change my oil every 4k or 8 months on the maverick hybrid?
@richcombs48054 ай бұрын
Keep in mind start/stops are the worst for an engine and what do hybrids do? They put engines thru the worst of frequent starts and stops and quite possibly never letting it get up to temperature.... I would change a hybrid oil MORE often.
@ramonahumada44 ай бұрын
Makes sense.I started every 3 k, but when I drain the oil it still looks super clean!
@richcombs48054 ай бұрын
@@ramonahumada4 well you could send a sample and Lake will review it via his Speediagnostix business like he did for me and then you could get a baseline to use to gauge future readings against. Winter time with short trips with generic gasoline should be the worst case time period. On that note, don't use generic gas.
@ramonahumada44 ай бұрын
Chevron and shell only and Pennzoil ultra platinum on my cars.
@wesa6652 ай бұрын
Modern oil filters remove 90+ % of small ultra fine metal particles on the very first pass through the filter. Fleet vehicles like fire trucks, ambulances, police cars, rental cars and most every none “car guru”. Never receive a break in oil change early. It’s 5,000 or 7,500 miles on the first and every subsequent oil change. Often using the cheaper oil and cheaper oil filters. Despite running all day long. Despite reaching 130mph daily. Think about the state trooper who gets a new Dodge Charger on a concentrated patrol week. It will be involved in at least once car chase at 140+ the car will be driven 5,000 before the first oil change if not 7500 depending on fleet maintenance requirements. That Charger will be driven hard daily for years. Then sold to a county sheriff who will drive it for another several years. Then auctioned off and used a a taxi or such. Look at the crown Vic cars still in use.
@nikkoBcoolАй бұрын
if it can last 300k with lousy maintanve it can last 600k with great maintenance
@orinmangar23334 ай бұрын
A question I have is the dealership usually places a sticker on windshield stating next oil change mileage or six months whichever comes first. Can a person who doesn't drive a lot go over the six months b4 an oil change?
@richcombs48054 ай бұрын
Best not to, due to condensation or dilution, since you likely arent often driving till good and hot.
@randy749894 ай бұрын
@@richcombs4805 It's a personal preference. Oil & filters are cheap, but engines are expensive. Just watch The Car Care Nut or Scotty Kilmer to learn about oil changes. And, the Motor Oil Geek agrees, six months or 5K, whichever occurs first. I don't care how many miles you drive... change the oil & filter, period.
@xlargetophat4 ай бұрын
Is ultra platinum Pennzoil the best oil??
@DrivenWildOutdoors4 ай бұрын
I don’t know for sure, it seems there’s a lot of opinions between Pennzoil and Valvoline
@kevinr.98963 ай бұрын
Yes it is
@xlargetophatАй бұрын
I changed to ultra pens oil. Drop 800 miles. My engine read 255° on the obd. Maybe this thin oil is getting my truck warmer than normal. So that's the take. I remember it use to be 240°f .. apparently 260° is when it's a red flag for boiling
@kevinr.9896Ай бұрын
@@xlargetophati use it in my jeep turbo wrangler and wheel hard terrain, never goes over 220.
@xlargetophatАй бұрын
@@kevinr.9896 apparently ford ranger 2nd generation 01-11 drive hot, so I've read. As long as the coolant doesn't go over 260°f
@diesel54604 ай бұрын
What can we use to help flush engine etc when doing a oil change
@lonniebeal60323 ай бұрын
Full synthetics with a high detergent package will slowly clean out the sludge. Projectfarms did an extensive test.
@drewk59294 ай бұрын
Best diesel oil? Worst diesel oil? Thanks
@DrivenWildOutdoors4 ай бұрын
Let me check on this.
@simonsays5824 ай бұрын
Schaeffer's the best.
@nikkoBcoolАй бұрын
Rotella T5 is what I run
@carlmcdonald58644 ай бұрын
I pick up my new ZR2 next weekend should I 1000km or les
@BeefNEggs0574 ай бұрын
You should be literate first.
@david88va4 ай бұрын
What a geek
@joeh66974 ай бұрын
Has anyone ever seen lake and steavo in the same room ?
@craigbenjamin196Ай бұрын
Be ware that engine stealing is done in repair places for u needs engine works.
@MrRmeadows4 ай бұрын
Will synthetic oil prevent sludge?
@LA_Commander4 ай бұрын
Yes, as long as you use a good quality brand and change it regularly
@kevinr.98963 ай бұрын
Penzoil ultra plat will
@simonmears17264 ай бұрын
Oils are much better these days however i am very fussy with my honey drop s because i like to make 300 thousand club plus 😂