The new bench mark in High to low level adapters from AudioControl LC2i Pro Car Stereo Lab

[@blacksethrogers]

My god you explain things so much clearer and with far less (and more understandable) words than this other car audio fabricator who does many of the same videos. It's not like you have to dumb it down either, but rather, you educate the viewer. Thanks for the video and keep up the good work

[@Michael_Anthony05]

Thanks, guys I learned something why my bass was so sloppy with the lc2i. I could never get it right. I am going to go out to my car and set it right. I was able to find where the bass rolls of but it would be too sensitive when I got to the point where the bass rolls of. Again thanks, why nobody ever made a video on that. awesome video guys keep them coming.

[@johnviera3884]

So did it work? I keep hearing about this thing but no real world reviews.

[@ricks_life2046]

Just ordered the pro for my new upgraded system. Complete upgrade. 3x as loud so I'm stoked to have this. Great job explaining it.

[@milesbautista6303]

Ordered my LC2i pro at crutchfield, cant wait to try it on.

[@lowhertzhighspl]

and?

[@pooda1076]

Can’t wait until the LC2i Pro is released 😁

[@CarMaintenanceGuy]

I got it now. It's really nice. I have the remote bass knob by my steering wheel. amzn.to/3g0EDKX Works awesome with my factory stereo. Just got it installed today! Using a Fosgate 500 watt amp (puts out 644 watts RMS @ 2 ohm) amzn.to/2WWj6LY SUPER CHEAP! The JL equivalent of this is nearly $400! This is less than 1/2 the cost!

[@feariraq3677]

I was looking into getting a lc2i now Oma just get the pro

[@crock2434]

Y'all my saviors ...almost ......keep up the good work..

[@randomsomeone1617]

What an incredibly informative video. This video is very helpful for those that understand. I personally am in the market for these products and this video has made me decide to hold off for a minute. I hate buying a product to only learn the next generation is weeks away. Dont take this as a negative. I love everything about this video. As soon as these new products drop, I'm all about them.

[@jerzeeal3368]

I use the AudioControl LC2i Pro in my 2010 Lincoln MKX on the factory navigation/sync radio and i love it...

[@bbchester6]

Very cool. Would love to see a video on tuning and gain matching multiple amplifiers.

[@davoupnya3202]

Thank you guys for another sneak-peak, and informative video ! You guys rock !!!

[@christiandshatto7765]

Thanks guys, car stereo Lab!!!!!! Christian😁

[@hooshfarperakis1282]

You guys are so helpful!! love it! keep doing what you are doing!

[@chaos4197]

Another great informational video. Thanks guys.

[@keithbailey5923]

Awesome video thank you

[@proffessasvids]

Awesome vid guys! I installed an lc2i into a friends audi a5 fastback. The accu bass sounded like the epicentre's octividing action which I don't like. Hurts my ears lol. I swear it puts in some subbass square harmonic or something. It would be would be wonderful if you guys could spectrum analyse an epic in action for a lab vid. I'm sure everyone would be interested to physically see what an epic does xx

[@melissathompson7229]

They already did this video and showed what it does with an RTA

[@proffessasvids]

Ah thanks@@melissathompson7229. I'll have a look xx

[@WindyCity1014]

I've got an Audi S5 Sportback and have been having an issue with the sub randomly failing to come on when I start the car. I'm currently using a Wavtech Link2 with a JL Audio 500/1 amp and 10" shallow mount sub. I'm thinking about switching the Link2 for the L2Ci--did you have any issues with the Audi's B&O system like I've described? Do I need to add an AC-LGD resistor as well?

[@treyporras08]

Can't wait for them to come out!

[@juansanchez210]

Finally some fernando back

[@MrPsiclone666]

i had a lc2i with my factory headuniit and loved it. got a kenwood headunit now and just left the lc2i in the car but turned off the accubass. I think from memory the accubass sends a clean 8v signal to my amps, where the kenwood sends a 4v signal. nyhows lc2i is a good unit

[@chriswhite4596]

Great Demonstration Dean !!!!!

[@brettbrassard7959]

Nice vid guys. Audio Control for the win!

[@cameronmochizuki1784]

Audio control should make a smaller epi center for those really tight spots

[@cameronmochizuki1784]

Maybe make it the size of the lc2i pro

[@juliobello4561]

LC2 is awesome product

[@bobbybyrkett7751]

Thank you professor

[@keithfarrell320]

Can this work to enhance a 2019 ram with the 19 Speaker Harman Kardon stereo. I have noticed the bass roll off just as described in your video. Please do a video on this vehicle when possible.

[@lowhertzhighspl]

they only do F-150s apparently, ha

[@TurboJohn74]

This is EXO's uncle, I swear lol

[@exodus3155]

LOL

[@bryanCLXT]

legit statement

[@KelvinTaylor-gu4xo]

Is the accubass light going to be on all the time ?

[@rommelmiranda2680]

Why didn't you test the voltage of the output of the LC1i for the purpose of a line driver?

[@mafosa8519]

not only that. the amp has a max volt threshold of 5 volts. no point of passing that.

[@DC2114-e3m]

How would you compare the LC2i or LC2i pro to the kicker Keyloc?

[@lylegoodluck]

I think I need the LC1i.. for some reason I have to turn my gain almost all the way up on my fosgate p1000x1bd.. I didn't have any problems with other Amps I used and tested. It seems to not see the signal..

[@superduperman323]

Hey fellas, can you do a tutorial like this on the new Epcienter Micro???

[@l.rod2827]

Great video, your attention to detail and craftsmanship is awesome. I installed a LC1i to my 2023 Ford F-150 Lariat which has the B&O system (not the unleashed). I added a single non ported 10" subwoofer with a 400 watt amp. I tied it to the factory installed subwoofer speaker wires for my line in and the rest is wired as you did in the video, works GREAT!!! But, i noticed when i turn off my truck and open the door, the music stops, the factory deck turns off but the LC1i and amp remain on for just over one minute. I tested and its pretty consistent. I also noticed that when I open a door the LC1i and amp turns back on and stays on for just over a minute with the deck off. I'm thinking there is much electronics in these newer vehicles and perhaps why I'm experiencing this, anyone else experience and what did they do to resolve?

[@l.rod2827]

I forgot to mention the trigger and delay happens in both the GTO and AUDIO settings.

[@moeasim3587]

I would love to see you guys do a cadillac xts. I have the lc2i and still notice the bass stop going up after 30. Unless you guys would recommend something better

[@lowhertzhighspl]

same here with my lc7i

[@rc121crx]

My fusion sport has the sony system which is worthless at idle or just with ignition sense on . Drive above 60 and it really gets rowdy for a factory setup. I've been holding out on the new audio control to fix this issue.

[@rhernandez5393]

What year sport? What's your setup?

[@rc121crx]

@@rhernandez5393 2010 and all factory 10 or 12 speaker setup. I just wish there was no vehicle speed volume control

[@slowbrezze]

it's your speed control setting on ford 1to 7 check that it gets loouder as speed increase at idle or park back down

[@rc121crx]

@@slowbrezze yeah it's at 7 but when it's set on off it's like 0 or negative 50 db. it truly sucks.

[@jorgearomoz3063]

Good work!!!✌️✌️

[@flightmedic7169]

I need to hook up an LC2i to a 2015 f150 Lariat. Do you know what speaker wires I need to tap in to ?

[@aaronsharp241]

Does the lc2-i have a built in line driver, pls answer

[@milesbautista6303]

Aaron Sharp it does

[@davidmcclain1292]

Any Idea when this is going to hit the market? I have a 2017 Chevy Sonic that i bought a Pioneer TS-WX70DA Powered Sub and was interested AC LC2i but this looks a lot easier to set up.

[@sp00f34]

my sound installer never mentioned to me that i needed an LC2i.... he just added that 20 dollar output converter and it's sounded pretty rough the whole time ive had it. im just now finding out that i needed the LC2i........... now i gotta call them and ask where they put it, so i can have someone swap it out for me. i knew something was off considering in my old car it sounded much better.

[@mikailernendaz6955]

Question.... My Kenwood Deck has bass roll off choices of -6, -12, -24 db but no off switch. What is the best setting.. And does it change gain settings. I used to have bass roll off at -12db but changed it to -6db....do I have to re adjust my gain?

[@HectorRodriguez-fe8xz]

Hello i have cherokee with premium system, i want to add a LC7i to add 2 amps with 2 more components and 2 subwoofers but i want to keep the stock speakers with their stock amp. From where should i get my signals?

[@anon8613]

How does this compare to the kicker keyloc?

[@FiveStarCarStereoInc]

The Key has a DSP for de-equalization

[@anon8613]

​@@FiveStarCarStereoIncty for your reply! What would you recommend for a 2020 mercedes e class for two 12 kicker q subs 2ohm, the Lc2i pro or the kicker keyloc? I was thinking of the Lc2i pro because I was told I need load generators. Or the keyloc for the auto eq and separate load generators?

[@ekimandersom4478]

Could i use the LC2i as a line driver? In other words, i have a Chinese headunit that only gives 2 volts from the low level outputs. Would it be better to use the high level outputs and a LC2i ??

[@nickeminoski2205]

So what load would you select for a Harley Davidson gts factory head unit?

[@gregoryswan1509]

Five Star, I do not have an LC2i, BUT I have a LC7i. Would the things you demonstrated on the video work for the LC7i? I have seen your videos on the LC7i and others as well, AND I'm still confused about it. I wrote to Audio Control and I'm still confused about it. Would you, OR ANY OTHER posters know the answer to this question I have about the LC7i: I have high level inputs going into it, my radio is AN AFTERMARKET Kenwood receiver (it does have the RCA line pre-outs in the back of the radio. I CHOSE NOT to use them cause at the time of installation I did not have the correct length of RCA cable, PLUS, I researched that the LC7i can output up to 8 volts to your amplifier, so hence my reasoning for using the high level inputs. YES, Audio Control also makes the DQDX, and another processor DQ-61 I think, that I can use RCA line inputs with to get even better sound.) Now back to my question, Is the OUTPUT coming from the LC7i to go into your amplifier a High level input, or a Low level input? My car amp can accept up to 4 volts using the RCA's, and up to 10 volts using the High level inputs. Thanks for reading my question, WHOMEVER could answer it.

[@abcdefghij2099]

Low level comes out of the LC7i, same with your kenwood rca pre outs. You need to measure the voltage coming out of the LC7i going into your amp making sure it doesn't go over 4v. You can avoid that step by just using the rca pre outs from your kenwood head unit

[@perplexedpat]

I have this installed on my 2019 street glide with the factory boom gts head unit. With HU volume at 75% I couldn’t get the “maximized” light to turn on even with the level knob maxed out. I measured output at the lc1i with a multimeter set on AC volts and it maxed out at 1.9v. The lc1i should be putting out 9+v. Have you seen this before and do you have any advice? Thanks

[@suprola7961]

So to defeat accubass, which way do I turn the knobs? Or can I just have it on all the time?

[@cruisertechgt]

Is the load resistors only needed for car audio systems when you remove a stock speaker and replace it with yours?

[@joshanator84]

Can you use that new lc1i line driver after the lc2i to clean distortion so that subs can hit alot more powerful without distortion light lighting up like Christmas trees? Basically setting lc2i ( maximized) then hooking line driver up and maximizing that, then the amp should be able to finally pound harder and higher on subs without the amp light coming on. Bass fanatic here, thanks haha.

[@ADD1distraction]

So happy to find this channel. Question if im simply adding a sub to a stock system, can I use the LC1i on the factory sub signal? I have previously used a basic rca converter so I do know it doesn't need a load on it. Any info is very appreciated.

[@RAW_Reality]

The short answer to this question is "yes". For better detail, I'd recommend watching the YT channel "Boost & Shutter ". They have a discussion & review video of the LC7i which you could use as a guide for the LC1i.

[@blk99xtreme]

Does anyone have any idea when the LC2I Pro will be available? I don't even see it on Audio Control's website...

[@thenotoriousrvh6091]

It's kind of out dated now but you should try out a Kicker Front Row in the lab. I can send you mine if y'all don't have one.

[@bgdogy]

Let me down Dean, at.11 seconds you could of had another great Sir Mix-A-Lot reference....Input, Output Carburetor full of soot! :)

[@sleepzzz800]

What is the ETA of the Lv2i pro? I’m wanting to get the lc2i but wondering if I should wait till the pro drops

[@CAPTIVMEDIA]

When is the PRO coming out??

[@Stop_the_cap311]

Out now

[@texasboyz713]

What about stock radio that dont show volume level 🤔

[@Premium_90]

Bmw e90 stock radio dont show volume level too

[@kenyanboyy]

Nice

[@Zachcamaj]

Do i need to run wires from left and right or can I get away with just from one side for only a sub

[@ericecheverria7008]

if i have a audio control DQ-61 would i need to still install loc?? i have a 2015 silverado reg cab no bose 8'' screen.

[@taylormoore4189]

Here's hoping this will assist with eliminating noise when integrating an aftermarket amp with a factory radio

[@joshymcdaniel9233]

Did it work? Used a pac loc made for my car $45 ish was a pos add an amp and noise from factory radio just amplifies 10x 😡

[@Ismael_Arenivar]

How would you know how much input voltage is going into the amps? Last I checked thet put out up to 8v which is too much for most amplifiers

[@jaydawg116]

They put up to 9.5v, actually! And you can test voltage on the rca outs on the LOC by testing it with with a few different tools, but AudioControl makes an RTA/Oscope that can test voltage and speaker polarity as well. I forget the model name, but it’s badass.

[@patsjoholm]

For a 2018 Q50 (no bose), is AccuBASS needed for this vehicle? Thanks!

[@cruisertechgt]

did you get the lc2i? accubase i think should be good to have on any system

[@patsjoholm]

@@cruisertechgt I ended up installing the Rockford Fosgate DSR1, instead of the lc2i. full range response is awesome and more control over the whole system.

[@cruisertechgt]

Patrick S nice what’s the difference between lc2i and the DSR1? Are they doing the same purpose like line output converter from speaker level to rca ?

[@patsjoholm]

@@cruisertechgt dsr1 is a full blown digital signal processor with line level or rca inputs. 8t gives more control over the entire system (fronts, rear, subs) where as the l2ci is a single in with bass correction only. Dsr1 allows for full system tuning.

[@patsjoholm]

Don't think I ever answered your question. As long as the signal is getting tied together between the front and rear speakers (which the DSR1 does), you don't need accubass. The front speakers do not play full range, whereas the back speakers do. The DSR1 ties both together, so the bass is there. You just can't use the stock fader to the front. The bass will be gone....

[@rafaelrosas2918]

Hey guys nice video what u guys think is better for upgrade my audi a4 system should i go with the lc7i or the pioneer dsp ?? Also want to know if the dash speakers can fit a3” midrange from focal thanks guys

[@charleswp71]

The pioneer DSP is not that good, very basic, you would be better served with the LC7I and a Dayton Audio DSP, or if you want one unit the DM608

[@rafaelrosas2918]

Charles Pack thanks

[@glassman3333]

I asked this question in the lc2i video, but the lc2i pro is basically the same, ao any help would be appreciated. Bear with me here. I have an Acura RSX (Bose system) with an aftermarket Kenwood head unit that has a 5V pre-out. I’m replacing the old amplified, self-contained Bose spare tire subwoofer and replacing it with a new amplified, self-contained JBL BassPro Hub. I’m keeping the front factory Bose amp. If I’m thinking about this correctly, the front factory amp just carries a remote turn on and speaker level outputs to the sub (it doesn’t amplify the sub), so is it even worth it to use the lc2i pro from the front factory amp to the new JBL sub, or should I just bypass the speaker level outputs from the factory amp, and instead use rca cables from the 5v pre-out in the Kenwood head unit to the JBL sub? I’m not sure, but I don’t think it matters if I bypass the factory amp (and ditch the lc2i pro), because the subwoofer isn’t amplified from there anyway. Am I correct in thinking this way, or in my case, is there still a benefit in using the lc2i pro?

[@chrisjarrett2473]

I have a question . I want to keep my factory radio in 2015 Hyundai Elantra and also add DSP because the radio only has bass,mid,treble controls what is the most budget friendly option? I say budget friendly because i'm raising my grandkids now thanks in advance.

[@charleswp71]

Do you have the base system or the "premium Infinity" system? Either way I would look at a LC7i, will give you nice clean RCA signal to build off of. A nice pioneer gm d9705 and the focal integration series speakers and a nice 10" sub

[@chrisjarrett2473]

@@charleswp71 I have the base system thanks ill look into the LC7i

[@slow_rednline4874]

@@chrisjarrett2473 that's what I use in my 17 Veloster with premium sound(dimension)

[@rogueghost2012]

Dayton Audio has a good “entry level” DSP that’s not too hard to figure out and is only about $150 usually.

[@elvy3236]

When this is gonna be out ??

[@Stop_the_cap311]

Out now

[@SuperBubba360]

Hi guys, do you know if the stock radio in a 2012 RS camaro has bass roll off?

[@1965themhs]

Please inform me about the phenomenon that when i turned on the Indy DB4.1x and i had connected the high-in plugs with amplified signal from my old gactory cd-radio, the amplifier (with +12v on rem) starting playing the output sound (non regulated with gains at low) but after few seconds the voice slowing down and finally disappeared . The sound (the same way) came back again when i cut the 12v from amplifier and connected back again. Any idea for this trouble? Is it possible to be problem the gain voltage? How can i measure the correct voltage, till the time that my amplifier is integrated with high in inputs included on the same apparatus. Thank you

[@DJKEYS-br1xh]

Hey guys I loved my lc2i I sold it an installed in a nother car

[@Grobyck]

Question, if using this with home audio, how do I supply it with the proper 12 volt power?

[@PURESOUND4]

You should be able to use a 3 amp 12 volt power supply.

[@mafosa8519]

on your receiver. you should have a 12v remote turn on for a external amp. that would work.

[@jmacinco]

New to this channel, I found myself binge watching. Question... I see you use a lot of audio-control products, I’m not sure which to use with what setup and why. Can you tell when and why you would Use/need these products?

[@PURESOUND4]

The products shown in this video were Line Out Converters, also called high-to-low converters. They take the speaker outputs from a stock radio, and convert that to a low level RCA style output, that carries the music signal to an aftermarket amplifier. These are great for integrating more powerful amplifiers while keeping the factory head unit (radio) in the dash, especially if you want to add an amp and subwoofer to a stock sound system for better bass.

[@rogueghost2012]

To explain further, these are active LOCs, not passive. That means they’re powered so they can push a better, more powerful signal (as well as accepting a powerful input signal), while a passive LOC might lose partial signal before the amp. Also, the AccuBass feature is unique so if your factory radio rolls off the bass it will restore it so you have a matching bass signal all the way up to your max clean volume.

[@AraceaeFanatics]

Up to 9 volts output on the line driver. That's what i was told.

[@PATHFINDER4001]

Any one know where these guys are located?

[@rogueghost2012]

Rick Venegas Clearwater, Florida

[@PATHFINDER4001]

bchooker thanks man right down the road 👍🏼

[@justchillin7274]

I don't think I my car has bass roll off.it's sounds good and only gets better as I turn it up. That smaller one seems good. I just hope its priced fair

[@jocaglorioso6739]

hey guys

[@asperkins]

I love your videos/channel, I've just never been a fan of the jump cut editing. I'd rather see more fluid video even if it has bloopers. Guess it's just my old f@rt as your likes speak for themselves.

[@michael55116]

Ok Carol Ann

[@trellatkins959]

2 VOLTS IN 9 VOLTS OUT IF THAT ANSWERS YOUR QUESTION!!

[@jocaglorioso6739]

show new products

[@dr38016]

666 likes,,,um naw bro,,,(hits like button) 667 likes now,,,thank me later.

[@Justice4allJustice4all]

LMAO 🤣

[@westwardmonk612]

Why is it taking so long 🤷🏽‍♂️

[@welder9163]

Don't waste your hard earned money on stereo equipment, you'll spend 5000 and still Not be happy, if you go to a shop!!