THE Quickshifter for EVERY BIKE! How to install the Healtech iQSE-1 on my GSXR1000 k7 k8 2007 2008

[@Kiwiiyt]

Wanna see the quickshifter work on the dyno? - > kzbin.info/www/bejne/mGK0ZICKm6yBhJY

[@feresearchit5473]

This is one of THE things everyone should buy to their bike.....works for up and down for most bikes...

[@Kiwiiyt]

i agree!

[@niko6743]

This would be a better video if you either turn down the music or off altogether. Upload your video again please

[@Conlan109]

Only goes for like the first two minutes. He's mumbling anyway, so no point to listen.

[@fserafeimgr]

OMG!! WRONG. what you do at about 4:30 is, you are shifting gears without the quickshifter being engaged because you have set the "First rpm" at 3000 and you shifting gears at 2800. That means that the quickshifter does not cut the engine yet. You have to be 3000 or more to engage the quickshifter or decrease the "First rpm" value at 2500 for example.. You are lucky that the bike was not on the ground..

[@KatrinaAlves-v7o]

I got the same bike a 2005. Could you please tell me where can I buy it?

[@toetaethep]

Quick question like if your bike come in with a quick shift well technically zx6r is the stock better or a customized quick shift someone please respond

[@andriesvanderwalt1849]

Do they do one for a Suzuki DRZ400SM and does it work

[@Kiwiiyt]

it does work, and they almost have it for all bikes, just check their website!

[@admendoza7680]

Does quickshifter works on carb type?

[@josecalderon4177]

I think if.

[@Kiwiiyt]

carbs use other tunes.. i guess it wont

[@AshishBalajiR]

Is it possible to install an autoblip or is there an option for autoblip with this system? So far I can only find irc quick shifter and autoblip system for the 08 gsxr 1000.

[@Kiwiiyt]

not that i know of, only knew about the quickshifter, you can tho down shift but its not a real blipper etc

[@sanoj1969]

So you can gear down to without using the clutch?

[@Kiwiiyt]

yes if you leave your throttle open , you can

[@Shermosakadermos]

Lekker bezig kerel mooie uitleg

[@Kiwiiyt]

Thanks!!

[@stomybugsy12]

Can this quickshifter be installed on a 2015 Suzuki GSXR 750?

[@Kiwiiyt]

Yeah look at the website of healtech, you can see which one you need 👌

[@DutchWesp]

Top filmpje weer maat ♥️🙌🏼🤩 duidelijke how-to!

[@Kiwiiyt]

Thnx!

[@dincageorge00]

works up and down ? or only up and to go down you use cluch??? thank you

[@Kiwiiyt]

Both can work, but you need to stay a bit on the gas to down shift.. i dont prefer it. I use it only for upshifts

[@abiyhmor]

Is this guide usable on a Gsx-R 750 k7? And did you get any problems with it ?

[@Kiwiiyt]

yes its the same, and no never had any problems!

[@abiyhmor]

Yeah but i can't really understand what you are saying because of that music.😅

[@abiyhmor]

Can you also downshift without using your clutch? I thought it was not possible.. 4:40 ?

[@Kiwiiyt]

@@abiyhmor it can, but only when you stay a bit on the gas, but its not designed todo it

[@abiyhmor]

​@@Kiwiiyt So it is not so healthy to do it..

[@galamototv]

Hello, i have suzuki GSXS1000F i have bought a quickshifter easy heal tech. Would you be so kind to show how you connected each cable? I really like your video.ty

[@Kiwiiyt]

Hi bryan its very easy, you need to put them in between the original cables. So they get inline!

[@ShaizyBwp]

Is that down shifting also work?

[@Kiwiiyt]

yes! if you stay ok the gas abit!

[@ShaizyBwp]

@@Kiwiiyt gas abit mean I don’t understand please kindly tell me

[@Kiwiiyt]

you need to stay on the gas when you dont shift

[@ShaizyBwp]

@@Kiwiiyt you mean to say little blick throttle and than can downshift

[@Kiwiiyt]

yes

[@steves365]

Mag ik vragen welke cut off tijd dat jij nu gebruikt? Standaard is 80ms.

[@Kiwiiyt]

Dat mag zeker, 45ms auto

[@steves365]

@@Kiwiiyt thanks. Ik zal het es proberen.

[@习近平-m5l]

If sensor value hits 100, it will up gear by itself right? That worries me

[@Kiwiiyt]

if the sensor = 100 your hitting the pedal.. no chance it will 100 bij it self, then your hardware is not on the right place

[@kenaitwo]

Decrease sensibility and you're good 👍

[@G20vtr]

Good vid, the same sensor works with the invert shift? i want to install on a 1000 k5

[@Kiwiiyt]

Thanks! Not sure m8! Down shifts work tho

[@steves365]

Yep. It also works with inverse shifting. It's working with strain sensor.

[@Waleed.alhamidi]

Will it affect the gearbox in the long run?

[@Kiwiiyt]

Cant really say, have had nog problems so far

[@stuartracing1]

It`s actually better because it is killing the engine in between shifts unlike using the clutch and the motor stays running

[@cameronaasman12]

Yeah this is actually completely fine. Bikes are made for it

[@kyodiwhitley7290]

Thank you!

[@mapetr1vr469]

hi listen i'm asking you could you take photos of your quickshifter settings because I can't get over it 😁👊🏻

[@Kiwiiyt]

cut off delay->15ms , cut-off times 45ms . Thats about it, if you wanna know more let me know!

[@nator8946]

@@Kiwiiyt would these settings work for 2012 suzuki gladius 650 (sv650)

[@Meifesto]

It seems really easy indeed.

[@Kiwiiyt]

It is really easy indeed! And a lot of fun after installation

[@Meifesto]

@@Kiwiiyt I can imagine it being a improvement on such a bike yes.

[@obmarhoj]

hello, Man. greetings from Saint Petersburg Russia, how u doin?) i've got the same bike, Gixxer K7 with the straight pipe, i wanna know, what about exhaust flame on shifting, it's possible with this device or not? )

[@Kiwiiyt]

yes, but you need to tune your ecu and remove the cat

[@obmarhoj]

@@Kiwiiyt hello, i've already installed tuned ECU, and straight exhaust pipe ( without cat).

[@Kiwiiyt]

Its after burn programmed on ecu

[@obmarhoj]

i have afterburn when i close the throttle from ±7000rpm then i have it. i want it on shifting,

[@Kiwiiyt]

then you need a quickshifter

[@aaronarman89]

Where did you place the sensor.? On the rod or on the shift link?

[@Kiwiiyt]

Hi aaron, send me a dm on insta, i will send you a picture!

[@stuartracing1]

You can install it on the pinch bolt for the shifter rod.

[@skipperide4914]

if you increase the cutting time, when you go high, doesn’t the bike have a more crisp sound when changing gears? the way the new bikes are with built-in quickshifter. in exchange, the sound seems more abusive and seems to crackle. good job. simply love gsxr all the best for you. a hug from Portugal

[@Kiwiiyt]

Thanks m8, did the times on a dyno so i think they are good!

[@saimencelli9049]

Hey man ik heb hem op mijn k5 1000 geïnstalleerd bijna identiek aan hoe jij hem hebt maar nu wil hij niet meer dan 3000 toeren meer maken rijdend heb je een idee wat verkeerd kan zitten?

[@Kiwiiyt]

Ow dat is vreemd, nee dan moet er iets niet goed aangesloten zitten. Ik heb meerdere mensen geholpen maar dit heb ik niet eerder gehoord. Stuur ze anders even een mail. Ze reagere meestal snel

[@saimencelli9049]

Kiwiiyt thnx voor je reactie! Ja het is vaag. Dacht eerst dat de sensor misschien te strak zat. Of het bobine harnasje niet goed... Maar twijfel nou ook of de massa op de accu wel zo goed is, zie dat ze toch echt chassis massa aanraden. Heb healtech gemaild even kijken of die nog ideeën hebben 👍

[@Kiwiiyt]

Nog goed gekomen?

[@saimencelli9049]

Kiwiiyt hey! Ja was een noob-mistake. Brandstofleiding naar de tank zat geknikt. Heb die tank zovaak omhoog gehad maar ineens zat die leiding niet meer lekker of scharniert hij niet goed mee. Anyway alles weer goed en quickshifter is top. Alleen nog beetje finetunen.

[@Kiwiiyt]

Saimencelli 90 gelukkig maar! Enjoy

[@QuarantaQuattro]

Down shift ?

[@Kiwiiyt]

Yep works aswel! Need to be on the gas tho!

[@rvaraceteam5465]

Hey there does this work on stock ecu or do you need power commander?

[@Kiwiiyt]

stock ecu is no problem

[@stuartracing1]

Dammit man,I wish this wasn't so expensive . I need one in the worst way,because of a medical condition with my foot.

[@Kiwiiyt]

275 euro that isnt that expensive is it?

[@stuartracing1]

@@Kiwiiyt Over $300 American...

[@Kiwiiyt]

Not that bad is it

[@stuartracing1]

@@Kiwiiyt It is for me...I guess I'll just have to deal with it.

[@SuperCamaro28]

how to know my Harness type ??

[@Kiwiiyt]

Go to their website, their is a selection tool!

[@ricardopais11]

Hello What is that silver thing inside your gas tank?

[@Kiwiiyt]

just the gastank

[@mapetr1vr469]

how much you gave for everything and what company it is

[@Kiwiiyt]

The quickshifter is from healtech, its arround 280 euro’s

[@RickOnTheBike]

Geabonneerd op je kanaal en uiteraard al wat vieuws er bij thumbs up leuke videos kerel !!

[@Kiwiiyt]

Thanks rick! Kheb het zelfde even gedaan 👍

[@RickOnTheBike]

@@Kiwiiyt Thanks maat !! :D

[@Mrmarginofsafety]

Muzak really

[@razorbak6783]

Yeah music sucks....can't hear you.

[@sanderjoosten3254]

Jammer van die bout muziek.

[@Kiwiiyt]

+Sander Joosten ieder zn ding toch

[@tonygrewal6217]

Hello mate.....Any ecu tuning required? I want to install on kawasaki z1000sx 2018?

[@Kiwiiyt]

Nope not needed just install and go!

[@predragsim6356]

can it change gears down or only up?

[@Kiwiiyt]

Only up, you can do down, if you stay a bit in the gas, but isnt made for it