How to fix Door Speakers on Jeep Cherokee - Fixing Broken Wires in Door Jamb

[@JustinNicholson-r3c]

11 years later and still helping

[@c45275]

One thing I like about KZbin and dudes like you are you save the working man time and money. Mucho appreciated keep the video coming.

[@ageingungracefullypushingt7135]

Just repaired a speaker wire yesterday. Never undertook a project like this before and no videos I searched on YT provided the exact info I needed so I reinvented the wheel from step one. If I had only been able to find this video it would have saved me tons of time!

[@TheOceanX]

Hands down the best write up for this particular issue. Well done and thank you for sharing the knowledge!

[@TheAmpLab]

You're very welcome.

[@dondercole4249]

Just wanted to let you know your video was a great help in disassembling diagnosing and repairing left front door speaker wiring many thanks!

[@danrowe79]

Common Jeep problem: GREAT video, good details, lighting and tips. Clear and comprehensive. Appreciate it.

[@ncognitod.460]

'99 XJ Limited here. Very glad I watched your video. People told me about the wires in the door jamb, but I didn't believe because my bundle was perfectly intact. Wire loom all sealed up & undisturbed from the factory. It was hard for me to believe that I had broken wires until I saw what yours looked like. Well, I guess I better get to work! Thank you so much for this video.

[@SuperRamcharger]

Well done Mr. Amp Lab! I have the power window and speaker issue in the left door panel, and although I am a professional mechanic, this will save me hours in regards to the door bellows and circuit board re-soldering (your other vid). I found that if I press the door lock button down and to the right just right, the buttons for the windows would illuminate and function, leading me to a circuit board problem, but you pinned it down. You have saved me hours of troubleshooting and I appreciate it. I also successfully pulled off an early engine ('92) I built into this 2000 and damn, it runs great, just high Nox issues but I know what the problem is. High combustion temps due to lean OBDII parameters and also aftermarket Bosch O2 sensors, ATK (NGK) are much faster responding and OE spec.

[@byronmitchell9305]

Just bought a 2001 Cherokee. The driver side speaker wasn't working. I had never had to do anything handy, especially on a car. After soldering the wrong wires and then losing the passenger speaker, I finally fixed both speakers all thanks to your video! If it wasn't for this video I would have had absolutely no idea what to do. Thanks!!

[@TheAmpLab]

Awesome! love the feedback!

[@masterjakeway]

I just came here to say, the tip to push the boot into the door makes it way easier! thanks man

[@erichimes3062]

Great video and very helpful. Some other things to do while you’re in there is to apply some fluid film to the door skin and spot weldsAnd get some silicone spray on the window tracks. It would also be a good opportunity to lubricate the pushrods for the door lock and handle mechanisms

[@robertmcdowell489]

I love KZbin and guys like you that have done all the brain work and put it on youtube to make it easy for us grunts. The driver side speaker was not working on my 2001 Jeep Cherokee also the passenger side window would not work using the passenger switch. I fixed both of these in a couple hours thanks to your video. I found the green wire broke just like yours on the radio, and the bad solder joints on the window switches. Thanks for your service.

[@jeffgreen8842]

Your video was perfect. Driver's side door speaker wasn't working when we bought a used Cherokee. Followed your directions to a tee, and the wires we the problem just as you stated. Thanks a ton for the info.

[@atpmusic1]

I owe this guy!! (and I had like 9 busted wires...)

[@DarinCates]

I made a continuity tester with sharp heavy wig pins, a light bulb and a 9volt battery. The wires that are not visualy broken can be tested by poking the pins in far ends of the wire insulation. Bless you brother for making this very helpful video.

[@Silkforge]

You can also use heatshrink butt connectors if you can't solder. This fix also sometimes can fix your power windows, passengers switches, and power locks depending on the wires that are broken in the door. Good video!

[@LsdLsp]

Great video. You just saved me 400+ dollars at cartoys. Had to fix both doors on my 98 2 door. Thanks for the info.

[@deandeibler8363]

Absolutely great video Bro. In the process of fixing my 2000 Cherokee as we speak. One of the best How-To vids on KZbin. Thank you Sir.

[@suncityhotshot5546]

Great video thank you

[@wesleyseigneur6692]

Wire broke in the same spot, had no issues soldering and putting everything back together. So good to finally hear my speakers again!

[@Vinny2142]

For the longest time my front speakers didn't work - I just figured they were blown out and the previous owner disconnected them. Took apart the doors and inspected the wires - SNAPPED at the connection in the boot. Problem's fixed now - really awesome and helpful video, thank you!

[@ljdavecolorado534]

Excellent set of videos! Thanks for posting! I fixed a friends 2000 XJ today. None of the power windows worked and the power locks didn't work. Found 5 broken wires in the door jam along with another 4 that were getting cut through. After fixing the wires, I needed to repair the solder joints on the arm rest controller circuit board. You two videos rocked and made it an easy job. I have a theory about the broken wires in the door jam. I believe they were caused by that 2 inch piece of rigid shrink tubing covering the speaker wires. After the wires for it broke, it pushed the end into the other wires causing the damage.

[@TheAmpLab]

I agree about the shrink tubing

[@Timk0810]

Just did this work on my '99 XJ. The wire in both driver and passenger side was broken. Exactly like you said, those are the only wires with some sort of hardened material around the connection which actually causes the wire to break off towards the end of that material. cut, spliced, soldered, wrapped. Stock speakers work great! Thanks for the video!

[@evanmiddlemas9961]

This video just helped me fix my speaker. This whole time I thought it was a bad speaker. It was a single wire right there in that door junction. Thank you!

[@beefcake3131]

You sir are the man. Thank you, I would have never figured this out.

[@petesreviews15]

Thanks so much! A++++ video and it cured my problem. We just bought a 2000 Cherokee Sport and only the rear speakers worked. I found the exact issue in the video in both door boots. Repaired the broken section (it indeed was the stiff heat-shrinked union that cracked out in both doors) and now the stereo sounds great. Thanks again for the fix and the video! Pete in Connecticut

[@rogerball2495]

Thanks for this video! Have a 2001Cherokee and I figured this had to be the cause of that speaker not working. Seeing the steps made such a difference! Couple of suggestions that worked well for me. Didn't pull that rubber boot all the way into the door. Close but left some out. Made it easier putting back. I'm not the best at soldering so instead, picked up some 22-18 weatherproof Butt Connectors. Don't plan on installing a tweeter and don't have the infinity System, so just cut and stripped the dark green speaker wire coming from the door, did the same with the one coming from Jeep body, stuck each stripped end into the different ends to the connector, crimped solidly and then heat treated the connector. Nice solid connection and no soldering! Finished off like you did and all is good. That rubber boot is fun getting to properly sit right but eventually did. Thanks again!

[@SavedByFaithInJesus]

Well done!! Thank you. I have been wondering about the speaker problem and window switch problem for a few years now. Turns out to be a REALLY quick and inexpensive fix. Thanks again! P.S. If you have any other fix-it videos for the Jeep Cherokee please upload them!!!

[@gabegreenhalge3455]

I just bought a 2001 Cherokee limited xj and the driver side speaker was working but the passenger wasn't, so i opened the door panel and tested the wires not thinking about the boot, hooked up the new speakers and wasn't getting any sound, watched your video went out saw the broken wire, connected them and got sound!!! Surprising but anyways your vid helped me save alot of time, Thank You!

[@SavedByFaithInJesus]

Had same problems, speakers and locks/windows. 2001 Jeep Cherokee Limited 4WD. I ran new wire for speakers, was more convenient. I also saved the fiberglass fabric and reused it. Watch when you pop the switch buttons, one of mine went flying and I didn't see where it landed... found it much, much later.... Fixed these issues in a few hours total, would have taken less if I hadn't been goofing off. Thank you very much!!!!

[@FireEater]

Great video thanks for sharing I went through the same procedure you mentioned because my car alarm stopped and doorlock stopped working I guess it’s on the alarm circuit but the way jeep has those wires going through that rubber boot are way too short had to add additional wire so it wouldn’t just pull apart. I didn’t cut the boot but to be honest it was a little tough getting the rubber flange behind the sheet metal and into the door jam thanks again it’s people like you that make the world a better place. 👌🏻

[@MrDkaljouw]

Thanks a million!! you saved me a fault search and made the fix fast and easy 😀😀 full sound system is back working in my 00 xj.

[@p.murray9767]

fixed mine today thanks to your video, don't know why I waited so long.

[@thomremington27]

wow...pushing the boot back into the DOOR ...!!... a lifesaver ..!!!...tks . ...!!!..

[@albertom.juarez6876]

Awesome video man. Cheers 🍻

[@scottbrown6289]

Thank you for taking the time for these videos!

[@joshthompson5686]

Awesome! Was able to fix the speaker problem and the power window issue in just a couple hours. Thanks for posting! Though I did get a little gung ho and popped the power window toggle d-pad and cant get it to work... looking back at your video you left it in place. Oh well, I can pull one pretty cheap hopefully, but as for now if I do need to adjust the mirror I can always do it manually. Thanks again!

[@knplwp2]

This worked for me...Thanks for the great video. You resolved an issue that I've had for years!!!

[@dbzsuperfan711]

Fixed my XJ, didn't even need a speaker, thanks man

[@JPike223]

Thank you so godamn much my dude, all of the speakers on mine went kaput, and i absolutely require music on drives so this absolutely saved my ass❤

[@blacksheep25251]

I know... 6 months later... this video rocks! Thank you, especially the part of the 6 1/2 speakers can fit in the doors. So many options now to drill a 1 3/4 hole just to the top right of the speaker and go to a cross over/tweeter woof combo! AWESOME!

[@RacerJames76]

You did a good job of explaining the issue, but since you followed a design flaw and did it the same way it will likely fail again. It is always better to pull the connector out of the kick panel and pull the harness into the door. Make your solder connections where they will be inside the door and in the kick panel so there is only fresh flexible wire in the boot area. Remember solder makes the surrounding wire stiff.

[@OrlandoCRamos]

Thanks for making this video. Had a speaker go out and I went out and bought new speakers. Turned out to be the same problem. Broken wire in the door jam. Was on a Dodge Ram, but same fix.

[@rickyg.3012]

good video! going through this stuff with the Cherokee i just got, my old 89 never had any issues..even while beating on it and it's a plow vehicle too! i did catch enough when you played with speaker to figure out 105.1 WTOS FM!

[@harrygatto]

I had similar problems on my RHD 1996 XJ where the electric windows would only operate with the driver's door in a certain position, obviously a problem in the wiring harness to the door. I took the whole harness out of the car, the biggest problem being disconnecting the plugs in the A post, not very much room there. The quality of the wiring in the door harness is terrible, some of the connections were just twisted together and taped so I replaced the broken wires and some of the others which felt very crusty. Like you I soldered all connections before taping everything well to keep the water out. It took a couple of hours or more to do but fixed the problems. Jeep wiring is generally poor quality so expect problems in headlight wiring for sure and it's probably best to replace all the cables connecting battery, alternator and starter plus ground cables too.

[@oilyfingers]

Thanks, nice video - used it years ago. just wanted to add: Please guys dont forget to put back the boot where it belongs. Friend of mine did not and went through carwash afterwards- real nice aquarium in the paasanger floor area. ☺

[@loveyourenergy4165]

Dude this was so helpful. Thanks. Same exact issue with my cherokee.

[@nateshelden6095]

Thank you so much! Miles above other car repair videos.

[@DuBxPS3]

Good video. I had the same problem. I bought new speakers and haven’t checked the wires yet, I am getting a dim light on the wire though, I hope it’s just a breaking wire.

[@Mattmazz77]

Thanks, I totally didn't think about the rubber boot trick.

[@eastbalkan]

That was my other problem in my car. Thank you this video too!

[@brick1167]

It is a very good video, it is instructive. Good job man

[@ianpalmer186]

Great video mate. Hopefully this will be the fix needed on my 2005 Grand Cherokee 👍

[@cobrathomas5492]

Outstanding video. Thank you.

[@LZDEN]

good how too guide...im replacing my door speakers soon and at the same time im looking at the wiring under the rubber boot as i have unlocking issues in my jeep.thanks for the guide ;-)

[@VideoNOLA]

Oddly, my 1999 Grand Cherokee had a big plastic grommet where the wire harness enters the door frame, which (a) made it impossible to "shove the rubber boot" inside the door, and (b) was really hard (impossible for me) to disconnect. Also no sheath around the wiring bundle, so nothing to "cut." So I had to work with all the wires while the boot kept trying to get in my way. And, oh yeah, there was like ZERO SLACK in the wire coming from the kick panel, so I wound up having to solder in extra wire to reconnect the ground (which was broken exactly like you said it was!). Just a warning for others attempting this maneuver; it was a pain in the butt in my case. (I even accidentally CUT one of the other wires, so had to fix it!)

[@IMPAXSK8]

Thank you so much. This is exactly what happened on my cherokee.

[@NursStace]

Perfect! You helped us fix the front driver side front speaker! Your other video helped us fix the power window lockout switch! Any advice for the rear speaker on the driver side in a 2001 Jeep Cherokee Limited? It’s dead too 🙄

[@jeepguy95]

The 1644Rs are pretty decent speakers... I paired four of 'em up with a Sony CDX-GT360MP receiver in my '94 ZJ Grand Cherokee, and I was on a budget, so these worked out well, I would've kept the non-premium factory speakers but they were on their way out.

[@timphillips9564]

Awesome video. Thank you very much for saving me a lot of time and money.

[@confederate8]

My son said his 99 XJ windows have been flakey. When he comes home from Christmas I know what we will be doing. Great video!

[@rrcoster]

Thanks for sharing this be very helpful start as my front speakers are not working on my 2000 Grand Cherokee

[@sunsetmemories8262]

This is a big help to my issue! Thanks !!

[@balsak_garage]

Nice video! I was able to get both front speakers working because of this. Putting those rubber boots back was a biatch though, any tips for that?

[@vidmag362]

Thanks. I can see my Jeep working properly again, in the very near future.

[@Symtrips]

Thank you for saving me an immense amount of time!

[@faith5584]

Hello, So I have a problem with my 2001 XJ Sport, there is no sound, The radio has time and when my dad took it out and hooked it up It worked, so we don't believe it’s the radio. While doing research I saw that a lot of people said there can be bad wiring in the door, we checked the wiring in the door and all the wires were fine, Now I'm not sure where to look. If its a wiring problem I'm not sure where, and all the speakers look good, but I can't promise the speakers are good, it just seems weird for all of them to be bad. Has anyone else had this same problem and were you able to fix it? Thanks in advance for all answers.

[@Daniel_P22]

I have the same problem right now, did you fix it?

[@faith5584]

@@Daniel_P22 Sadly no, I still haven’t gotten it fixed. Sorry I couldn’t help you, hopefully this summer I’ll get it fixed. Lord willing.

[@Daniel_P22]

@@faith5584 bummer I hope you do! I actually fixed mine it was the speaker wires on both sides of the doors

[@seanneal552]

Thanks for the video. Exactly the same issue on my 2000 XJ. Easy fix.

[@samparks9443]

thanks for your video it was very helpfull and you explaned everything great

[@jeremysooley2946]

Awesome vid! Do any of those wires connect to the door light? Both my driver side speaker and light are out and I'm thinking some wires broke in the door. If so please reply

[@SuperUnreal2000]

Hey alright alright alright! Awesome video! I have a question though, would it make sense to, instead of resoldering the exact same weak spot, splicing in some new extra wire?

[@TheAmpLab]

You absolutely could. Chances are though this fix will outlast the Jeep.

[@duckkiller223]

Great video, i just bought a jeep and I have a problem and have no idea how to fix it, I checked all my wires and they are all in tact and I don't believe my speakers are blown. Is there any other thing I could do to make them work. Thanks

[@TheJessicav]

Great Videos. How about horn and cruise control not working along with the other things you repaired? Would these items have a similar fix?

[@TheAmpLab]

Not sure. Never had to fix those issues

[@katk7685]

Clock spring needs to be replaced for horn and cruise control.

[@AbuGrabIt]

Wow dude this is one great video!

[@highwayxj9397]

Thanks for the fix. I’m just confused as to why the door panel has to come off. Seems like the wires are easy enough to access

[@madcook1936]

Awesome video thanks for sharing this I will start on mine tomorrow

[@mjoslyn1612]

Great video man. Thanks for the help!

[@brownietheking3397]

My right front is only speaker that works I opened driver side fixed all those broken wire like u instructed but it still dont work neither do backs just the damn left front any suggestions

[@lJUSTwanaCOMMENT]

Is the yellow and black wire for the separate tweeter? My driver's tweeter is disconnected somehow. It doesn't have the infinity system; I'm installing AM component speakers and I would really like the tweeter wiring to work. Any guidance would be so much appreciated.

[@ThePOWERtoRULE]

Thanks for posting this!!! Awesome helpful video!!!

[@Katarinarabbit]

My problem got a 1996 Jeep xj no power going to rear passenger speaker examining under dash. Any solutions?

[@ASKAI1962]

VERY VERY VERY HELPFUL. EXACTLY MY ISSUE

[@chineena]

Excellent video.

[@jasonm1690]

Thanks for posting this! I just picked up a 2000 Sport same color blue, and the driver side speaker is out. I have a 14.5 hour shift tomorrow with a lot of down time...so you know what I will be doing lol.

[@TheAmpLab]

Hopefully it doesnt take you the whole 14.5 hours. lol Hour job at most

[@TheAmpLab]

Soo...did it work after? :)

[@jessebabisz2349]

Both driver side speakers in my 98 Cherokee are broken. Pretty sure this is what the problem is on the drivers door, but what do you think about the rear speaker? Thanks man

[@TheAmpLab]

I would say the rear is probably blown more than likely. They're in the ceiling, so the wire doesn't travel through any moving parts or pinch points that i know of, so it's likely the speaker itself.

[@markbuilds]

Super helpful, thank you!

[@AEON.]

Is there are cheap alternative for the door unlock and alarm key fob? Really don't want to spend a billion dollars on a lock smith. I took the fuse out for the horn. 2000 Jeep Grand Cherokee - got it used, didn't come with the key fobs. Would be nice to find an app for my galaxy note 4 or galaxy tab 3 to use it to unlock and turn on/off the alarm lol.

[@lucaslopez1375]

i have a 2001 g.j cherokee the speakers have static and sound goes high n low do you think it's the wiring or do i need to replace the speakers?

[@Havenator1]

awesome video. Thanks for the help!

[@laithalsabbagh2255]

Yo thanks allot man, but can you do the same thing for the rear speakers as well?!! Please

[@thomaspresley9225]

super helpful, bro. thanks a lot

[@markgabello58]

I have a 2001 Jeep Grand Cherokee driver side speakers not working looked at replacing tweeters to with the infinity gold is there a way to test that the speaker there use a ohm meter

[@Buck7388]

You rock been looking for help on this ty

[@survivaleveryday]

Excellent video.....

[@dre04mach]

A lot of the fixes I see have to do with windows, yet no one touches the locks. Most people when they have issues with the locks it's the windows that are gone as well. can that be the same issue - the wires in the doors and/or solder points that you cover in the other video? My power windows work well.

[@Patrick.Wedow1]

this video was fucking awesome. its people like you that make me love youtube. i could not find the way to fix this at all

[@francishart6075]

What's the cost of a job like that may be?I like to know please. ❤

[@bucs2superbowl03]

Thanks and great video I have the same problem

[@kenwaldeck6307]

That was the fix !! Thank You !!!!!!

[@watchthisusa]

Great Videos!! Thanks a lot for the info!!!