How to Calibrate an ESC in less than 5 Minutes (2020)

[@acheron5900]

Seriously this is the ONLY way that worked for me thank you man! My setup: Pixhawk 2.4.8/ hobbywing xrotor 40A esc/ Racerstar 3508 motors

[@andyrodrigoalvarado118]

I was scared but it was so simple, thanks dude, have a really nice day

[@joserobertoviana6383]

Essa foi a melhor explicação sobre a regulagem da aceleração...... Parabéns pelo vídeo

[@carwils1956]

Thanks a lot, you are easy to follow.

[@mohammedabrarahmed3299]

That was under 3 minutes. Thanks pretty straight forward.

[@George25]

One small detail it’s not clear for those having an arming switch , do you turn your arming switch on and keep it on during the calibration ?

[@kunad2294]

just what i'm looking for, the best.

[@alexjimenez6020]

Thank you very much! Great explanation!!

[@heck2993]

my new esc wont double beep, just keeps single beeping every few seconds, anyone know why? Im assuming its just a shoddy esc

[@NBC_NCO]

Very good . I will give it a try. I've been working on a 1:32 scale touring car with a 10 amp drone esc. I got it to work, but not properly. One other thing. I'm not using a flight board. I dont know if that will make a difference. Any suggestions would be helpful. Thank you.

[@ekeneokpareke5656]

Please help: We are new to RC aircraft, and we are stuck on this process. After following your calibration instructions step by step, we move the throttle up slightly and then the motor jerks and stops then beeps 3 times as if it's confirming the calibration again. When I push the throttle up again, it jerks again and repeats the process. If you leave the throttle up, it beeps non-stop like a warning. What could be wrong? Thanks in advance.

[@raadkasem]

How to calibrate my Holybro QAV250 pix23 v6 but without having a joystick ? is it possible ? if yes, please gave me some hints to start searching

[@Supriyadi-Cartographer]

really helping THANKYOU so much 🙏

[@كثيرالطيب]

Thank you It’s help me so much I am fro Kuwait 🇰🇼

[@dustinplee5067]

How can I recalibrate my hobby queen brushless ESC it’s for a RC car and my motor is not even moving hardly any needs to be recalibrated I was trying to find a video on KZbin but need some help does this process work for any ESC

[@mrsparkles5294]

Im not hearing any beeps after plugging in the batterie. Could a bad motor stop the esc from calibraying?

[@arshishbalaporia7088]

Could you explain as to why does it happen though? Like why sometimes ESC causes the scenario where you give half the throttle and then it starts..

[@shiramyers]

Can anyone help, my esc just keeps continuously beeping

[@Boris_Woodwards]

Are you turning it on before the controller?

[@avirupsaha4701]

Can we recalibrate esc s

[@boredtuber997]

Thank you man love you

[@oadka]

Great video!

[@thedronedojo]

Thank you!! Glad it helped :)

[@chrisrox36]

Hi! Great video! How would I do this with a pistol grip controller? I have an austar AX5S connected to a generic brushless 40a esc. Any help would be greatly appreciated! Thank you sir!

[@rahulbhardwaj7762]

while trying to calibrate my 2 ESC they don't create those 2 ding sound and after that three . SO unable to calibrate any other issue which i can check ?

[@joncelagura5238]

Thank you very much for this video I almost got a headache with my rc boat lol

[@thedronedojo]

Haha glad the video helped you! I've certainly been there

[@atharvbadkas5452]

Ding ding😂 nice job😅👌🏻

[@ryansattele2875]

Thank you 😀

[@thedronedojo]

No problem!

[@riko7005]

Thank you very much!

[@Archer_82]

Thank you

[@mxaxy9594]

Thanks you solved ma problem.

[@Inventmr]

Tq sir this trick is working, 👍👍😋🙏

[@aliislamshimul89]

Thank so much. jajakallah khairan

[@Pwndrift]

THANK YOU!