This Silicone Trick Will Change the Way You Apply Silicone!

In this video, we showed the silicone application methods. Thanks to the methods in the video, you will be able to apply silicone more easily and you will be able to apply silicone properly every time. If you need to apply silicone in your home, you can make much better silicone by applying the silicone tricks, silicone tips and silicone hacks in this video.

[@Uldy]

Just curious but why did you disregard tip 2 on the rest of the examples?

[@danielcoetzee5793]

Yes, I noticed that too. Then checked the comments to see whether anyone else commented on that.

[@1982james111]

I think it's because if you do a straight cut on the tip it will have a natural curve and leave the silicon with a better consistent finish as apposed to having bulges running it back the normal way. When running the normal way you cut the tip at an angle which this video shows after tip 2. Tip 2 can cause you to judder on wood or rough surfaces, he used this method on smooth tiles which wouldn't judder and provides a better finish with a straight cut tip being used. Hope this answered your question 👍🏻

[@zackrog1270]

Because they can't caulk for shit 😂

[@АмэйзингЧенал]

😝

[@CostlyFiddle]

Tip 2 was an afterthought and added to the #2 spot by mistake in edit.

[@man-observing-world]

After 15 years of me caulking, this guy finally showed me to squeeze the caulk out of the pointy end, mind blowing…

[@jgfreer8322]

😂

[@PishtuYual]

I liked the part where he showed that using too fat of a bead wastes more than using a smaller bead

[@darekp_02]

fajny film, najlepszy ze wszystkich. Ja bym dodał jeszcze cięcie skośne końcówki wtedy też zgodnie z posuwem ładnie się silikon rozprowadza

[@norbertkulon4006]

Ta dla przedszkola nie dla profi

[@supermolibden5037]

Fajny gość. Najpierw pokazuje aby tubę z silikonem pchać, a nie ciągnąć, w celu uzyskania jednorodnej spoiny a potem już sam tak nie robi ,tylko ją ciągnie , nie grożąc sobie paluszkiem. Rewelacja.

[@norbertkulon4006]

Bzdury pokazuje kropka

[@marioas1964]

Great tips! although tip 5 should've be done like is shown on tip 2. 👍

[@lcfflc3887]

LOL i saw that too.

[@BibiFirebug]

Actually if you look at the tip it is properly angled in no 5 therefore there is no need to compensate for wrong cut or hole too big. Which is the point of the lighter trick too, but if no flamage is to be had, then you can still fall back to no 2. Especially if someone else cut the tip because that’s the way they’ve always done it!!! Would have saved me a lot of rework

[@andrewbritch5821]

Most definitely will have to remember theirs trikes thank you

[@tjpprojects7192]

Heat gun? I love using a method of removing caulk that will damage everything around the caulk and maybe set my house on fire.

[@qtzt8278]

Oh great 👍🏻👍🏻 These will be a great help to me later ...I am mending something in my house using silicone glue and have no idea how I should do it in a proper way. Thanks sir 😃

[@Mipetz38]

Good job, caulk always dries for me, will try those different sealings

[@ChromeArty]

I've been screaming this for years! The manufacturers don't even know how to apply their product! They indicate cutting the nozzle at an angle, NO! You cut it 90° to the tube and PUSH the silicone!! Bravo man! Finally someone gets it!!

[@ibe966]

It's funny how #2 and #3 contradict each-other with regard to flow direction.

[@ericbaker7615]

I think I'm going to continue applying silicone as I have . My way is better

[@abdshandcraft]

Trik yang sangat bermanfaat dan membantu, terimakasih sudah berbagi 🙏

[@daynosdr]

this guy loves calk!

[@ПетърИванов-ю9й]

Bravo! You are super! Good job!

[@highgatehandyman6479]

Silicone needs a wet finger run over it really. especially in corners. long runs like the one shown are easy. but it gets tricky to stay neat and work quickly in corners where 3 lines meet.

[@adrianlovic6486]

So do U push or pull ?

[@dewminrashindu2616]

This trick help my job ❤

[@Just_a_nic]

0:40 - don't apply silicone moving backwards! 1:10 - ok, move backwards. 😂😂😂

[@trueaussie9230]

Don't you think posting your criticism once is enough?!

[@Just_a_nic]

@@trueaussie9230 sorry, it happened by accident.

[@ЕкатеринаКулакова-о3ч]

Первый раз спецом нож под меньшим углом держал.

[@jordanhinderliter3784]

Well I’m not even gonna watch the video, I saw the finger wag. Funk would be proud!

[@barbarosmaxtan871]

Bravo ustam

[@sammypotpie]

To remove caulk do you have to buy that exact black and decker heat gun?

[@MegaZekid]

La cosa che non ho capito ,appena consigli di usare il tubo di silicone andando avanti, dopo tutte le altre dimostrazione sono andando in dietro :)

[@naamalaster9554]

Hey Maker, great suff - but on tip number 5 you're doing what you said NOT to do on tip number 2. LOL.

[@PoEt121]

Thank you thank you 🙏

[@davidegral7152]

Excellent ideas 👍

[@lmwlmw4468]

Nice.

[@sambrannan7550]

Shows right to left trick and the next trick goes right back to going left to right LOL

[@susanarodriguezdiaz4480]

Gracias!!!

[@daddy1571]

Do you like black caulk?

[@birchthebirch4593]

quick important message for all of you out there DO NOT USE A HEAT GUN ON YOUR TILES,BATH OR SHOWER ! if you go this far I'll tell you why. Tiles crack with heat differentials, adhesive on tiles de-bonds(have fun re-tiling), cast iron baths/ trays crack, fibreglass baths / trays deform, enamel cracks, epoxy cracks . DO NOT USE HEAT TO REMOVE SILICONE

[@poppyd9758]

First of all the reason you get uneven bead is you’re using the cheapest caulk gun you can buy. Secondly only putting down dotted lines to make a smooth bead is wrong because when you do that you create air bubbles which will make the silicone fail faster. How do I know? I’m a professional caulker with 30+ years experience. I’ve waterproofed the outside of high rise buildings that are still sealed after 20 years.

[@emrecenkers9721]

Hello, other than dotting, are all the tricks right here ?

[@poppyd9758]

@@emrecenkers9721 the reason why urethane always fails is the center of the bead has a stronger adhesion in the center and the edges pull away. After cleaning the substrate lay a tiny bead of silicone into the corner. Let dry then run a bigger bead over top of the silicone. Remember to be very neat because the urethane will not adhere to the silicone therefore the edges are stronger than the center. It’s called a bond breaker.

[@emrecenkers9721]

@@poppyd9758 Thank you for the quick reply.

[@youki4817]

저도 당신의 의견이 동의합니다 부드러운 비드를 만들기위해 점선을 만드는 것은 잘못 되었죠. 몇번의 연습으로 숙달하면 실리콘헤라가 없이도 원터치로 가능하죠 이게 베스트라고 생각합니더.

[@HyperionBadger]

I don't understand how to caulk and have a beautiful clean rounded seal. What am I doing wrong? Is the caulk gun I bought from Walmart garbo? Am I releasing too much? Am I going to slow? Do I cut the tip in a specific way? I'm pretty handy, but for some odd reason there are little skills like this that I have trouble with lol

[@thehazelnutspread]

At the beginning you told us NOT to go backwards but to go FOREWARDS with the caulking gun and then in all the other examples you went BACKWARDS........WHY?

[@Censor999]

This video is troll

[@dollydope]

Because they’re different tricks to fix the same problem. You’re not supposed to use all of the tricks at the same time

[@117Bahamamama]

Options

[@jamie-ox8sg]

Because he's Italian the only thing they can do is make pizza and pasta the maker tried his hand at silicon and failed massively

[@richardthomas5454]

That's because all of his examples are terrible, look at the way he changes the angle of the blade in the first example. I've managed to get caulk off perfectly with a Stanley blade without heating it. Even the example of going forward is not be best finish and anyone knows that gaffa taping the end of caulk doesn't really seal it. Rubbish video.

[@fanfam]

2:46 proceeds to aply from left to right after telling otherwise. But all in all I learned.

[@chepunator]

показывает что слева направо нельзя вести, а сам так и продолжает

[@serzid8843]

И точками насрал, что потом видно неровное нанасение

[@AchillesWrath1]

wags finger not to drag the caulk gun but to push with it instead. continues to drag the caulk gun the rest of the video

[@TheOuterDrive]

Umm..why did you apply less caulk on the second bead.? And why are you not using your finger or a tool to push caulk into the gap? Don't cut such a big hole in your tip , use a wet rag to wet your fingers to help to reduce friction...The only time you're gonna lay a bead that you don't " finger " is if it's big gaps on exterior oil based caulk . Check your tip periodically to make sure the angle hasn't worn away, ...

[@m3photo726]

Funny how he recommends pushing in the first example and in all the others he lays the silicone like everyone else in the world …

[@Big74Mike2012]

Well, they didn't help very much... maybe try talking next time. With all the crazy background noise, it's not like you're trying to make a pleasant, noise-free video, so you might as well explain!!

[@cherrygabs4939]

At 0:37 he says not to apply it going backwards but recommends forwards. After that, the rest of the tutorials shows him applying it going backwards anyway. :/

[@lionellosanti]

I like how this kind of videos are only useful for the info you can gather from the comments rather than the video itself.

[@Bruce-js3ci]

Always wanted to say something like that but never could put the thought to paper. 👍

[@LA_Lady84]

Amazing but I wish you could speak

[@pierreboissonneault]

Vous n'utilisez pas votre méthode de pousser vers l'avant décrite à 00:45

[@EddiesCustomsandRestorations]

#1 was a terrible example because you were shaving 90% of that silicone on purpose. You had a different angle on your blade when you did the heat gun method

[@namas-yra-namas]

Что только не придумаешь пока не срежеш кончик под углом... А там и всюду подойдёшь нанести с разных сторон и направлений, контроль лучше.. но главное сразу после нанесения обработать шов снимая излишки и предавая форму. Совет греть перед срезом? Так герметики с разными свойствами, для одного может и актуально, а другому не будет никакого эффекта.. По мне то такими ,,советами" запутываете.. профи так не делают

[@ЕвгенийЕвгений-ф8щ]

ну и где логика? в одном отрезке показывает, что пистолет с силиконом надо двигать от себя и во всех последующих двигает на себя...)

[@LAP1050]

The Maker, good tips👍. However, why did you not use continue using the PUSH method on your subsequent examples 🤔

[@icawn]

Good on you for calling his ass out 😆

[@zeez3139]

Do not use heat gun near a window as it will crack it !

[@jankuna9479]

If you protect the glass of the window then you can use a heat gun even there.

[@zeez3139]

@@jankuna9479 yes actually I did this the other day to dry sealant .protected with a thin board.Wish I had known earlier as without a shield it got damaged

[@jankuna9479]

@@zeez3139 Happened to me too. "Wer nicht hören will, muss fühlen“ - German saying. "If you don't want to listen, find out the hard way." Have a nice day.

[@ЛеонидМышалов]

Ага! Конечно! С пластиковых панелей я так буду силикон удалять, - расплавлю все нафиг! Зато силикон хорошо отойдет!

[@middleage_crisis]

Что ж вы сами-то не используете свой волшебный метод толкания пистолета, а везде на видео делаете протяжку? :))

[@J_ismyname48]

Why would anyone cut the caulk tip straight anyways? I've been a remodeler most of my adult life and I always cut them at a 45 and you can both pull and push without any problems at all if you know how to run a caulk gun .

[@wolfka1000]

😂😂😂😂😂😂😂Chápu že pro neznalé je to SUPER ale pro nás co ze silikonem dělají už léta jsou to naprosté blbosti .

[@AsinineComment]

Odd how he demonstrates the 'push forward' action, then repeatedly does the flawed 'drag backward' action. 🤷🏼‍♂️ Now HE gets the wagging finger, from all of us. 😜

[@kelvenguard]

I’ve been putting tape on the end for 30 years in the Autobody shop... only give it a pump and fill the tape with silicon, Winshield urethane, seam sealer etc

[@melvinhunt6976]

I like the way that the proper way to caulk is made to look wrong! I caulked for 35 years and talent is talent! It takes a while to become good but if l can do it so can anyone who really try’s!

[@justinmills3852]

I know lol. Never seen anyone in the trade push instead of drag. That's incredibly dumb

[@andremartinez5127]

I don't see where anything was "made" to look wrong. I did see someone taking the time to address beginner problems with solutions that may help those that don't have "talent" but at least have some interest in becoming better at something that does take a little time acquiring the coordination and skill to lay down a bead of caulk that bridges the legs of both joints. Real talent does quality work with least amount of effort and material waste. The "proper way" is all perspective cause anything can be made to look good on the outside, yet covering the mistakes made on the inside. How many walls, windows, doors, showers, are replaced because a 35 year talented professional didn't lay a bead of caulk properly by code? Or better yet didn't use the correct type for the application. Come on now, instead of being negative why not add some positive feedback to the person trying making an effort to help others become more confident working with sealants. Have a good day and be safe out there.

[@justinmills3852]

@@andremartinez5127 this didn't solve a problem or make it easier. There is less caulk in that joint and I'm sure it's so thin if there is any movement in material that it would Crack or separate. The reason some things are done the way they are is maybe not because it's the "right way" but it's the necessary way of laying down a sufficient bead of caulk and getting the most longevity out of the application. Most videos like this solve little problems and muddy the waters with people who think they know how to do something but have no clue.

[@melvinhunt6976]

@@andremartinez5127 get over it! This guy is saying that he knows what he’s doing! He’s trying but the x says the correct way and the ✅ is vice versus! How about saying that this method is different and not to say which is correct or incorrect!

[@andremartinez5127]

Thanks for replies gentlemen have a great day

[@Eric-xv5eb]

Tells you to “push” instead of “pull” the caulk gun and then proceeds to pull the rest of the video.

[@timschutte6924]

Some of this I do agree with depending on what you are caulking , where. How, and what you are caulking. But let me tell you that I have over 45 years EXPERIENCE caulking EVERYTHING, EVERYWHERE. if a person doesn't use there finger to go over the caulk after they have applied it. Take away the caulking gun from them. I literally caulk something at some point almost every day.

[@Spiritcr1jsher]

@Timbo Dewabem which is why a perfectly straight black object was used .

[@MrMatador29]

anyone wanting to remove sealant without burning their baths can always use some penetrating spray like a wd40, spray over lightly, it will start to break down in 15-20 mins, you will however need to use a white spirit/clean spirit works too before applying the new stuff

[@pspro9893]

Сначала показал что надо силикон «вперед» накладывать, а потом сам же везде тянет тюбик назад. Такая дичь

[@andybiss3757]

this person is only diy and not a professional.... professionals would definetly not do it his way..

[@lovetrump1088]

Example one is always....squeeze out WAY too much caulk and two is squeeze out about the right amount. YEP...works better every time putting down the right amount and straight. But the REAL Key to Caulking - from one whose done Marble Tubs/Surrounds and Home painting/building for years...is of course to choose the right size cut on the nozzle, squeeze out the right amount as you move the caulk gun along first, but then....MOST IMPORTANT ---- Use a rag and the right solvent and keep your finger clean as you press the bead home into the joint and clean up any excess - FROM your FINGER. For Latex Caulk, all you need is a H2O/Damp Rag to wipe your finger on as you run you a finger over the caulk. Keeping ur finger clear of any excess caulk allows you to press in and clean up the caulk perfectly every time. But wipe 10-15 inches, then clean your finger as it builds up, then wipe another section and clean the finger again...repeating until done. Any Excess - if it happens, can be wiped up with the clean end of the rag to ensure you have Zero over smear (if that happens at all which it won't if u get 1st part half way right and don't put on WAY too much like in this video). For Silicone Caulk, replace the H2O damp rag with Acetone and also use a spray bottle of Acetone. Use an acetone damped rag in one hand like described above, but in addition before you wipe with finger you also spray a light mist over the bead/work before you Run your finger down across the bead. It keeps the Silicone from sticking to area outside your bead and keeps your Finger clean as you wipe small sections, as you wipe rag to keep finger clean of excess. So Wipe/Clean Finger then Wipe/Clean Finger as you caulk with both Silicone and Latex and you get Perfect Beads every time. It is all about using the right solvent and a rag handy as u push the bead in to ensure it stays perfectly clean

[@mehul6828]

Please make a video - how to prevent the bottled from dry after used silicon , so it can be reused after longtime.🙏

[@TheMuse6959]

I shove a nail down then tape. Helps pull hard plug out to free the still good caulk.

[@qt3dot14ish]

It all has a functional shelf-life. Even unopened caulk will eventually spoil. Open caulk spoils much faster, no matter how you seal it. Nothing is askew with any of this. It eventually dries out. That's just life. If there's a "long time" between needed uses, you just have to purchase another tube.

[@JustAnAcre]

Doesn't matter which method you apply caulk as long as it works for you. The reason is that there are many variables, but the main one is level of control of the pumping hand as the rate of caulk flow is key.

[@Rodogg7787]

As long as you cover the Crack or whatever it is you are trying to cover, that's all that matters!

[@GODh8sfag5]

When I apply cock it always works and pumps

[@mathiasmathias8278]

And mainly Experience

[@hman2912]

His first goes were always deliberately faster and more erratic

[@markthomasson5077]

Women are the best, amazing what they can do with a wet finger. Oh, and men get overexcited and tend to pump to quickly

[@josipdrazin6708]

yes scalpel... when you damage the furniture call me to repair 👍

[@paulywalnuts9045]

You could also apply a Bead of Silicone.!Then Spray the Bead of Silicone with Soapy Water. Wet your finger and Wipe the Silicone.

[@TheMadJester159]

This is the equivalent of a bad infomercial.

[@steliokontos3427]

I use silicone and caulk basically every day and i cant say these arent good techniques but using a newer caulk gun would also help and with the lighter it would help people to see more than only the side view of what you were showing them a huge part of all this work is the size of the exit hole personally i dont always have the time to do little spurts i have to be able to seal up every edge in a room in about 15-20 minutes but for something small that would come in handy or something that isnt being rushed. Im not saying amy of these are bad tips and the last ones i use myself gotta plug the caulk and hooks are my go to or screws but over all i do like this video just need a little more for people who are watching this for home use

[@AsinineComment]

Excellent points. I too noticed the work on the tip, wasn't captured properly.

[@BibiFirebug]

Thanks for the tip

[@am-hz1el]

Apart from your videos being useful, you present the videos in natural tone, without any disturbing music, which is great and beautiful, and thanks for that!

[@1islam1]

⚠️ God has said in the Quran: 🔴 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 )} 📖Quran

[@dnappi85]

As a painter for 20 years. And applying about 500 miles of caulk until my fingers are bleeding(some days). This is absolutely Trash. Lol. Good for a million views tho. Good luck everyone.

[@MasterYoist]

@@1islam1 the Quran also says convert the Infidel through live and deception. For those who will not convert destroy them.

[@aselergeshova2812]

@@1islam1 👍

[@joeysplats3209]

I prefer a polite Southern accent with some gentle reggae background.

[@electronicsNmore]

Incredible how many views for a video with finger wiggling and no talking.

[@이준호-i7u4y]

따봉 개킹받네 지가 못짜서 실리콘 엉망된걸 가지고 왼쪽아니고 오른쪽 따봉 이러고 있네 ..

[@carlosm.823]

why don't you mix 2nd & 3rd trick?

[@bigbothoee8617]

Ball crap why was the blade angle different

[@Leningrad_DE]

Во втором совете показывает что надо двигать сопло вперед, а в третьем делает наоборот

[@renski8976]

I'm sorry, but a lot of these methods are Bullshit, especially since when you show the "messy" way you very obviously fuck up the bead and make it look like shit (inconsistsnt pressure on the trigger, and speed). Then your "hack" looks a bit better because you actually took your time to do it right. The "hack" where you make the tip flat with the lighter is plain dumb, just cut a small 60 degree angle on the tip and you're good to go. Also, a good quality caulking gun goes a long way for consistant beads.

[@ai4px]

Seems to really help when you turn the blade down into the surface rather that parallel to it when scraping caulk.

[@Eleventyseven9228]

Thumbs down for the finger wag

[@mo_mo1995]

Title: Teach you apply silicone! 1st clip: Remove silicone 2nd clip: Don't go that way. Go this way! The rest of the video: Yeah I'm going back to that way

[@brynybach7741]

Thank you for these tips. Every day is a school day 🙂👍

[@ireissistable]

Have a proper look at the caulk in tip 4. It's terrible lol

[@codyjarvis3426]

I've been a home builder and remodeling all my life , caulking can't be done backwards on wood , rough surfaces as it will get caught on splinters, holes ,nails ECT. It has to be pulled . Maybe smooth surface . But it real just takes a lot of doing it to know how much to push out and the speed you move . Plus you have to run your finger down it anyway for it to be correct. Silicone is even tricker. As it is sticker than painters caulk. Practice practice.

[@tomwijnen5416]

Really annoying how instructionvideos evolved... Nonverbal, pedantic, fingerpointing and rather narcissistic...

[@rhsking05]

So pulling the caulking gun instead of pushing it is the “incorrect” way to do it. Then the very next tip is you PULLING the caulking gun instead of pushing it!!! Way to not even follow your own advice that you literally shown right before abandoning it, lol.

[@Icantball67]

Useless! Nothing in here is useful. You’re better off spending a few bucks on some cheap silicone, find some scrap materials and practice. You’ll get better results practicing than taking these tips. There’s no explanation as to why these methods are better other than taking someone’s word. Just go practice.

[@prosto_mayster]

Цікаво, дякую за інформацію! 🤘😎🇺🇦

[@Mainbusfail]

Wait,. You forgot the futuristic tech disco trap music set at 10 points higher than our speakers can withstand. You also forgot to perform the unboxing of the products shown in the video and one last thing. Where is all the mindless life story ridden dialogue?......oh wait.......my bad. This is a well executed and thought out instructional video aimed at critical thinking adults. Smh. I get so confused these days. Lol.

[@QtheLaserDude]

Sure, let me go buy a completely unrelated tool for an insignificant problem that already has an easy fix... I swear these KZbin 'handymen' will never do work in my home.

[@jonathonwilliams93]

I work in the aircraft industry and the 2nd way is how we get taught to seal fuel tanks, fuselages etc as it fills the potential void areas better. I'm inclined to agree the 2nd way is better.

[@tuck6464]

You're saying you were trained to push your caulking gun ?

[@jonathonwilliams93]

@tuck6464 they're not caulking guns in the aircraft industry but its the same basic philosophy and yes we were trained to do it properly

[@tuck6464]

So, you take that home with you when you have caulking to do around the house?@@jonathonwilliams93

[@salimriyadi99]

Terimakasih

[@That0neGuy124]

out here solving problems that no one knew existed

[@zackrog1270]

Pushing the caulk gun tip forward is generally a terrible idea, but caulking two perfectly smooth solid slabs without any joint is the most controlled scenario and it turned out alright. I'll definitely try it next time! However it doesn't help for most real world applications. Cutting the tip properly and coordinating the movement of the gun with the flow of caulk is the best way to ensure a good product. Nice video

[@jnicemiz]

Yah this. the comparison shown in this video is ridiculous. careless application with a poorly cut tip vs a purposefully and carefully applied bead.

[@donbrownist]

When you pull the caulk it spans the joint and then you have to tool the caulk to force it into the joint. When you push the caulk you force it into the joint and leave a little excess on top. If it were possible the best caulking job would fill the gap with no leftover exposed caulk.

[@jnicemiz]

@@donbrownist Not true. You can get the joint filled when pulling the caulk just fine. Proper hole side, proper tip cut angle, proper application angle, speed, etc will give a bead that requires little to no tooling, and a higher quality bead than pushing the caulk. Of course, any truly professional quality joint will require tooling anyway unless it's an exterior caulking that specifically states not to tool.

[@boblewis5558]

@@donbrownist check out the technique I outlined in a post above. GUARANTEES zero over run, GUARANTEES filling the joint ... You can keep going over it applying pressure on the caulk. GUARANTEES the most professional, highest quality joint better than ANY pro can achieve with a gun, including invisible joints if required (only really viable on an initial install) I have the results to prove it!

[@BibiFirebug]

@@jnicemizthe exaggeration is a bit over the top but for a noob like me it helped prove the points. Had i seen this video before I wouldn’t be re-caulking today.

[@danielsandoval9556]

I’ve been caulking for well over ten years, and this video is very deceiving.. you must cut the tip to a 45* . No matter how good the caulk bead looks you must always tool it in both directions in order to create a perfect seal

[@FDT-Atlanta]

Hysterical that they first show that you should "push" the caulk into place, but then in the techniques that follow they show the wrong way to do a small bead by "pulling" the caulk gun.

[@rp9674]

I hate this mime shht, describe it in your language, make the video universally understandable. It comes off smug.

[@buricleo6464]

Prvi prikaz pokazuje da se silikon pravilno nanosi s desna na lijevo, a sve nakon toga nanosi s lijeva na desno???

[@Chaos_God_of_Fate]

This is up there with those 'life-hack' videos. Too many things wrong with this video- I'm not even going to try.

[@MetinTetiker]

Sayın Dostum.Paylaşımınız mutlak yol gösterici oluyor muhakkak.Aynı zamanda iyi bir kullanıcı olarak dikkatli,özenli uygulamalarınız ilgi çekiyor.Zaman zaman çokça her alanda paylaşımları ilgiyle izliyoruz.Bir konuda görüş bildirmek beklentilerin daha farklı olduğuda ayrı bir gerçek.Şöyleki,tanıtılan üürün,aletiyle,kullanım şekliyle doğru orantılı olmalı.En azından doğru uygulamaların paylaşımları doldurmalı diye düşünüyorum.Mastiklerin,silikonların,kullanım ihtiyaç aralığını dikkate alarak uygulamaya geçilmeli.Mastik kartuşları farklı farklı imalatlarla karşımıza çıkıyor.Bunlardanmbiri kademeli kartuş ucu ve kapaklı olması en doğru tercihtir.Bunun anlamı mastik çekilecek boşluk hesaplanıp,kartuşun kademelerinde uygun çap seçilip oradan kesim yapılıp uygulamaya geçilmeli.Boşluk olmayan kısımların üzerine çekilen mastik zamanla çatlaklar gösterebilir.sıcak su temizliğinde deforma kısımlar çıkabilir.Olası uzakta olsa ihtimaller.Ama esas konu mastiklerin kullanım hatalarından dolayı yarısı boşa çıkıyor.Bir daha kullanılmaz durumda çöp oluyor.En önemli olgu sizinde gösterdiğiniz şekliyle hızlı,ince satıh,elle müdahaleye yer vermeden güzel zarif görüntü elde etmek.Paylaşımınız için teşekkürler.Gelecek paylaşımlarınızda mastik çeşitleri,kullanım alanları taşıma ve sızdırmazlık güçleri ne kadardır?Gibi bilgi içeren pasajlar halinde karşımıza çıkarsa seviniriz.

[@claytidwell]

um Just curious but why did you NOT use tip 2, on all the rest of your examples of the correct ways?

[@pedromarrero6711]

This is like of of those garden hose commercials. Are you tired of dealing with your garden hose? And the actor is all tangled up with the hose.

[@The-Real-aPOC]

Makes no difference what method I use, as it always ends up looking like a 3 year olds finger painting.

[@Toscanto]

Vraiment n'importe quoi pour poser un joint silicone il faut toujours tirer le pistolet et pas avancer Ho que oui ... Et j'ai passé des kilomètres et des kilomètres de joints de toutes sortes