My civic has 2 wires going to the tail light. I connected the black wire to the black ground (I'm assuming) that goes to the bulb. I then connected the yellow and red to the hot wire that goes to the bulb. Not sure where else to put the yellow wire. Any suggestions?
@aaroncarter4014 жыл бұрын
Did you ever figure the wiring out I'm confused
@michaelt3084 жыл бұрын
Thanks for taking the time to make this video and share this !
@MesserAaron132 жыл бұрын
Mine blinks when I let off of the brake and doesn’t let me go through modes.. any reason why?
@trinitrang29323 жыл бұрын
Why doesn’t my left and right brake lights brighten up when I step on the brakes ? But they are working when the head lights are on .
@Al-ch4vl5 жыл бұрын
Well done explained video. I would buy the blinking tail light bulbs that blink 3 times and set that center brake light to do the same.
@MidwestMotor6 жыл бұрын
I just bought this module and worried about the programming, heard it was complicated so thank you for showing us!!
@dimlylitgarage97856 жыл бұрын
Glad to help!
@nickg24736 жыл бұрын
Really appreciate this video!! I couldn’t find any other videos to show how to program modes. I’m assuming I need 2 (one for each break light)
@doobedi3 жыл бұрын
Will these work for my SUV tail lights?
@doobedi3 жыл бұрын
Can these work for my suv tail lights?
@nickg24736 жыл бұрын
I’m confused because I have 3 wires going into my car’s brake light LED cluster. I have a 2016 Ford Explorer..I’m also confused when it says wire that goes to the brake pedal? Which one is that lol
@DailyDoseOfFingerboarding7 жыл бұрын
You should do what I did and put LED strips inside of the engine lid. So you can see it light through the slits, of loovers, however you spell it. You can pair those lights with some LED lights in the air intakes
@roydi51227 жыл бұрын
You know what I can get a rain guard for the trunk
@Jonstitzel7 жыл бұрын
Will this work on my skateboard?
@dimlylitgarage97857 жыл бұрын
Oh yeah of course
@Reetrealtor4 жыл бұрын
Hey man question, i installed mdule in my 2006 c350, but my third brake light error message came on. Light flashes but once the message comes on it stops working. Did you encounter something similar?
@dasfreakster5 жыл бұрын
How did you repair that deck isolation pad that was brittle?
@JUKE179r11 ай бұрын
Cheers from England!
@victorrincon71186 жыл бұрын
Im planing on putting those on my focus st aftermarket tailight, but im wondering what happens if your car batt dies, do you have to reset the hole thing again?
@aphromew45025 жыл бұрын
Keep making content bro!
@drivetosurvive72425 жыл бұрын
From my research, this is the only CALIFORNIA LEGAL brake light modulator..........Deceleration Warning Lights 25251.5. (c) Any stoplamp or supplemental stoplamp required or permitted by Section 24603 may be equipped so as to flash not more than four times within the first four seconds after actuation by application of the brakes. Amended Ch. 410, Stats. 1983. Effective January 1, 1984.
@archmasterone2 жыл бұрын
Good job, very organized presentation.
@Element21VA3 жыл бұрын
I can say following behind a couple of cars that had this, it works VERY well, all cars should really have it, much safer. For me it feels like your so much more alerted then just having a brighter red shine as you slow down to a stop, which could be easily mistaken as you still moving from afar.( Highway situations and bunch other on the road ) in my opinion, this is the way to go with brake lights and cars. 👍 Thanks for the vid
@gsheverything_27167 жыл бұрын
I didn't think I would like the video, but I was an excellent video man
@dimlylitgarage97857 жыл бұрын
Im glad you liked it!
@AzraelMalakh77 жыл бұрын
i was wondering if you have any issues of water leaking in a rainy day? I am about to buy this car and that's the only issue I am worrying about...
@dimlylitgarage97857 жыл бұрын
I haven't had any issues, the module is water proof and you can cover up any exposed wires and you should be fine.
@VlatkoVeselinovski5 жыл бұрын
did you get can bus errror?
@08ms3red5 жыл бұрын
Why did you stop Posting
@droo38515 жыл бұрын
Should never poke holes to check for power... that's how corrosion happens
@lfrankl534 жыл бұрын
Minutes later he used heat shrink for the connections. And if you do want to use a test light to put a hole in your insulation, put something besides your finger behind it....
@AlexEFrair6 жыл бұрын
Hey what's up! Really liked the video Just a question, which car did you like the most the mr2 or the 350z? I'm looking into buying one of those two, hope I get a suggestion thank you
@tylercook77396 жыл бұрын
I'm selling my 350z to get an mr2. If that helps at all.
@bulldogkarma5 жыл бұрын
Does anyone know how to connect to all three brake lights?
@robertackermann49444 жыл бұрын
You would have to to connect the flasher module between the brake switch (usually under the dash and above the brake pedal) and the point at which the wire coming from that brake switch branches off to each of the three bulbs. In other words, connect the flasher module to the wire coming off the brake switch that has voltage only when you depress the brake pedal. The red wire on the flasher module connects to the wire coming off the brake switch that has voltage only when you depress the brake pedal (which you will have to cut for this to work), the black wire on the flasher module connects to any good ground, and the yellow wire on the flasher module connects to the wire going to the three brake bulbs (the other half of the wire that you cut earlier).
@nbs_vlogz17084 жыл бұрын
Robert Ackermann I did it to my taillights but it only works when the truck is off, idk if it’s because I programmed it while having the truck on and running
@nbs_vlogz17084 жыл бұрын
Robert Ackermann any info on what I did wrong?
@RobertFWWhitlock4 жыл бұрын
Best is when necessity for braking is limited as much as possible
@thereluctanthipster97146 жыл бұрын
Are you still making videos? I really like your channel guys.
@leejiaginn5 жыл бұрын
Missing
@amedzul25582 жыл бұрын
Nice
@shanebeaudrot7773 жыл бұрын
I like it 👍
@1silvervespa4 жыл бұрын
I would have gone the extra mile and bought the two connectors from a junk yard or dealer and just attached them to the module. Leaving the harness uncut ... And reversible.
@jotu1734 жыл бұрын
I think you meant to say versatility instead of modularity.
@lsccarvideos4 жыл бұрын
Great video.
@ChristopherLemane7 жыл бұрын
This is a good idea. Its a small car.
@flipbrosat11944 жыл бұрын
Come back!
@ronaldcrosthwaite64765 жыл бұрын
I will have my mechanic view your youtube video. Looking at having him install it for me. I will buy it on the web site. Thanks for your straight forward installation video.
@WendenWarrior3 жыл бұрын
If your brakelight flashes every time you press the pedal, it’s just childish and idiotic. I would like to buy a proper Solution which works only at hard emergency braking