This 2000W Subwoofer Amp is Impressive

[@wal]

*Stinger Audio MT-2000.1 2000W Subwoofer Amplifier* Shop for this Amp: amzn.to/3PI6Muy Double Rock DR-2000.1: amzn.to/3rhmtiM Down4Sound JP23 v1.5 (many colors!): lddy.no/1hx46 Get your WAL/OSS Merch: bigdwiz.creator-spring.com/ Buy Me a Coffee/Tea/Slap-a-D-No : www.oldschoolstereo.com/p/donate.html Support OSS / Williston Audio Labs for early access to videos: www.patreon.com/OldSchoolStereo _DISCLAIMER: This video and description contains affiliate links, which means that if you purchase from one of the product links, I may receive a small commission. As an Amazon Associate I earn from qualifying purchases_

[@bartowflorida]

I saw over 2,000 watts at 2ohms

[@Kenmarshallintereststx]

Been running this amp for a little over a month now no issues I bought it mainly for the efficiency and the value is incredible kind of sad to see the efficiency this go-round because at the moment I'm hooking up a tar amp bass 3K plus this I need every bit of efficiency

[@Kenmarshallintereststx]

How would you rate this one compared to the recoil?

[@ROCKBOTTOMCUSTOMS]

I'd like to see a strapping test with 2 of them 🤔

[@JasonWW2000]

​@@bartowfloridaYes, it was probably just a very short burst. Perfectly normal.

[@Jonjims1532]

Car audio out here getting more and more affordable and im here for it.

[@JasonWW2000]

A big part of amps getting cheaper is better transistors. As they improve and can handle even higher amounts of amperage, plus cost less to make we will see prices keep going down.

[@jamescorfield534]

I know huh!?

[@samwise4me903]

To me, the most impressive aspect of this amp was the low operating temperature. This bodes well for its longevity.

[@d77543020]

I just ordered the 2K and running it at 2 ohms stock electrical 4 gauge OFC and the amp doesn't even get warm I don't care what anyone else says this is the best bang for your buck amplifier out right now

[@torrescesar71]

Thats what i do i never run amps to the max

[@ryanamen6397]

Poor amp

[@beekeeper8474]

Poor thing is probably low volting

[@d77543020]

It's fine like I said I was running it at two ohms ​@@beekeeper8474

[@provident8732]

Nothing wrong. Do you drive around with your music on full blast no. So stop

[@girthquake9655]

Honestly these amps are extremely impressive for the value.

[@jhansen6180]

I don’t see how the expensive brands can keep up their scams of charging 5X to 10x as much. I understand efficiency and distortion…..

[@agent363]

3k stetsom is almost there with the price,, +1000w more and no problems with rca 😂

[@xchimnyx]

Not really they're full bridge.

[@JasonWW2000]

​@@jhansen6180You can basically say anything is a scam. Its an opinion, not a fact. A fact is that different products have different prices. It really is as simple as that.

[@towboatjeff]

I bought the 1500w stinger amp and I've been extremely satisfied with its performance so far. Definitely worth the money.

[@wal]

Appreciate the feedback! I test this stuff for you guys and always appreciate to hear your experiences. Thanks!

[@alphaomega8373]

How hot does it get?

[@towboatjeff]

@alphaomega8373 I honestly couldn't tell ya at the moment. I never put a temp gun on it and I'm away at work now for another 10 days.

[@supadupa6891]

@@walyou da man DWiz!

[@shawnelliott3257]

@@wal Please for the 4 channels amp dyno.... waiting so I can make one complete purchase

[@msunmshop5449]

Thanks again Big D! I came to the party early enough to get me an MT 1000.1 ( they were selling fast when I looked). Because of you and your videos, 3 of my friends picked one up as well. What you do is much appreciated sir!

[@PrydeWater901]

At a time when seemingly everything is increasing in price for no apparent reason, it’s nice to see value brands coming through for the consumer.

[@JasonWW2000]

Remember the pandemic? When factories all over the world shut down? We are still not recovered. When factories shut down, there's less products. This can increase the prices. When shipping costs double or triple, this raises prices. So yes, there is a very good reason.

[@bdc211]

​@@JasonWW2000ohhh, you mean that plannedemic???

[@JasonWW2000]

@@bdc211 No.

[@danielreynolds178]

If you notice. The o ly real things that have increased are the things you have to have. The wants haven't really changed. These amps, speakers and other luxuries, leather couches can still be bought for 1200 bucks at stores everywhere. All the home suites are the same. Tons of stuff is. Just not the needs-food, bills, cars and such.

[@v12alpine]

I replaced an old rockford 360.2 with the 1000w version not only does it run much cooler, but it resolved a ground loop noise coming out of the highs amp apparenty caused by the rockford. Win win.

[@audiokeller1975]

You just had a defective topaz diode that avoids noise in those oldschool Rockfords 😊 they often fail, you can measure it with multimeter if your main ground has connection ( 0 ohms ) to RCA shield, a working topaz diode shows around 1000 ohms between main ground and RCA shield, it’s an easy fix 👍

[@JasonWW2000]

As great as the old Rockfords are, using one on a sub is not advisable. They will run really hot and suck up a lot of amperage. Class D is where its at for subs. 👍

[@audiokeller1975]

@@JasonWW2000 then you have to readjust the idle current on class ab Rockfords , most of the old Rockfords which run hot have a wrong bias setting or they are driving a load which is way to low in terms of ohms. But correct, even the oldschool class bd Rockfords stay way cooler 👍

[@scottholt3545]

I purchased this amp right after I watched your last video on he 1000w stinger. I had no issues with the rca jacks at all. Had some feed back noise. It has been fixed. I highly recommend this amp. This amp at 1ohmis a little power hungry

[@mattburgess2]

Hows this amp holding up? Been a year now. I'm thinking of grabbing one.

[@volvo09]

I like the little bass remote. Unless you need more information (like voltage, or clip indicator) there is no need for bass knobs to be large.

[@LatvianVideo]

I personally want the clip indicator, very useful info if you want to push the amp to its max and dont want to kill your sub

[@samus40glock]

I been a Rockford Fosgate fan since the 90’s. I believe I’ll be going with Stinger for my next daily driver.

[@swindlemcnastay]

This amp pushes my Sundown x3 12" hard!

[@BigSteve_Gaming187]

I am SO happy. I finally got my hands on all the Bass Mekanik music I'm aware of. Including the cds I purchased in the very early 2000s, which I smartfully backed up. Lovin' It!

[@BlueDinnie]

I love when things work as advertised or better 😎

[@miomejia606]

I bought this one right after u received the smaller one very very happy with it hooked up to 4 8inch skar audio subs sounds great

[@HifiVega]

Back in the day those street wire RCA’s would rip the terminal out! Looks like Stinger is putting out budget bangers! Great video

[@ruikazane5123]

Now that I remember...I had one that broke the center pin while plugged in and was hard to extract. Never used cheapos ever since!

[@bruth6138]

AAMP is a customer of ours. They are doing a great job! These no nonsense mono amps are a great buy.

[@joshuaferris8728]

I purchased this amp after you did the review for the 1000.1 it’s awesome!!

[@joshuaferris8728]

My rca connections were fine. On this model. Got it running at 2 ohm to 4-8 inch Rockville k6 subs and it pounds

[@Ninoo187]

You should post a video 😎 I wanna see them flex 💪

[@ecooutdoors]

Stinger power baby!!! Awesome 2023 amp choice

[@onesikm3]

After 3 months of daily use I’m extremely satisfied with my purchase! No unwanted floor noise either great unit I recommend anyone who is thinking about it to just get it stop thinking 😊

[@wal]

Excellent feedback, thanks!

[@csj9619]

Bought an MT2000.1 around the time of this video and couldn't be happier with my purchase. I've got it powering one Sundown U-18 and it DUMPS!

[@MrBarkley76]

As soon as he did the test on the smaller stinger,i bougt two of the MT-2000. I was shocked at the weight. Its small, but very solid/heavy,and a great sounding amp. Nice review!!!!

[@wal]

👌😝👍

[@stevemaniaci4750]

Cool nice amp ,impressive. Reminds me of the old school Rockford amps back in the late 80s early 90s . Glad stinger came out with it.

[@digitalbilly]

just found this channel so cool i miss all this old car audio

[@fulanito47]

I had the same issue with the RCA connector! Actually broke off on one of them. I was looking forward on this amp to bump my 2-10s. Well returning for an exchange!

[@x5-acousticguitarstuff.2]

I am 60 y/o and I just bought a 2023 26" MONGOOSE FIREBALL SS Dirt Jumper Mountain Bike. Cool Video.

[@csj9619]

48 years old and ride a DK Sentry 24". Love the simplicity of BMX.

[@huhdidwhat]

I'm 44 and I drive a Chevy. What's the topic again??

[@jamescole0951]

Can you compare this amp to the new audiocontrol epic2000 they sure look like the same amp with an added power output for a epicenter

[@thecman26]

Dayuumm! That lil guy is a beast and a DEAL! I've had some tight RCAs in the past and tight is ALWAYS better than loose! Thats what he said!

[@wtmf80]

Crazy that you and Jones came out with a video on the same amp on the same day.

[@FrenicX]

I have purchased two of these 2ks in the last 5 weeks and the first one I received Jan 27th had the RCAs that were waay too tight, but the second one which I purchased a week ago was perfectly fine. I also purchased a 700w and a 1500w and neither had the issue. Hopefully this means they've solved the component supply line problem! But a super hot drill bit of the correct size solves it too!

[@jhenry48809]

Since my old BP1200 is at it's end of life, I did a bit of research today watching your videos. I just ordered this amp with your link, it should be here Tuesday to play with. Funny I commented on this video 7 months ago too. 🤣

[@ChefVegan]

Where was this back in 1999?! Could have saved me a fortune.

[@JasonWW2000]

The transistors and other semiconductor components did not exist back then. They cost a lot more and couldn't handle the power. Plus no one had a good class D design they could steal and copy from. Same for computers. Imagine the iPhone 14 in 1999. The parts just didn't exist back then. Lol

[@ChefVegan]

@@JasonWW2000 thanks 👍🏻

[@jasonoctane4787]

I got one and it’s a power house. Blew a 15” black diamond and then a 15” kicker comp. Deciding on going with Stinger’s dual 12” loaded enclosure or a single Sundown U15.

[@paulposton393]

Let’s see them 4 channels stinger

[@albertlce777]

Like fr

[@AlexanderStein-db3ro]

Yes !

[@gregkirby]

@@paulposton393 same! I'm on the fence about repairing my alpine 1000w 4 channel. Or going with the stinger mt600.4

[@HotRod-wv4vm]

Thanks Big D! I wondered what happened to you and realized that my iPhone software upgrade deleted some of my KZbin subscriptions. I didn’t mind some of the others but yours definitely 😢

[@riinaldo]

Bought the mt-1000.1 after seeing your video, sheesh! Best amp purchase ever.

[@kevinAuman1]

These are a good deal if they are able to hold up over time in a hot trunk

[@derekgardin1512]

Well they run cool so should be fine as long as you mount it so it gets airflow underneath as well.

[@johannjohann6523]

Stinger is going to be my next subwoofer amp I buy. Good stuff, and designed well. Very efficient amps that are going to run cooler than the competition. Stinger is stirring up the car amplifier market big time!

[@user-uc5tj6ux8w]

I bought one of these 2kW amps after watching your 1kW review; glad to see this one performs just as well.

[@pigsoldier193]

Just got this and the 700 watt one. Putting it in a 1971 el camino with 2 punch p3 15s. Im 52 but when i was 16 a friend of mine had 2 punch 15s and could hear him blocks away every morning on his way to work

[@matthewf1979]

I have always been happy with Stinger products. Their cables, wires and insulation/sound deadening is a fantastic value. It seems their amps are too!

[@ericdye5056]

Got myself the mt-2000.1 and its powering 2 12" dual 4ohm hyanka subs wired to 1 ohm. Pretty sure im gonna have to get a new latch and switch out all my bulbs to l.e.d's because this setup is insane. Especially in a box i fabbed myself to utilize as much space as possible in my 98 bmw convertible. Would, without hesitation, recommend this amp to anyone. Do yourself a favor and get a lithium d4s lto 6.0 batt with 500 amp isolator. Wish i could shake your hand for pointing me in the right direction. Love it

[@SnubBarracuda]

If you are running those Funky Pups you don't need to use any of the speaker outputs. The built in blueteef will automatically receive twice as much as the amp is putting out.

[@huhdidwhat]

I'm confused about that comment, could you please clarify - what are funky pups and twice as much what?

[@SnubBarracuda]

@@huhdidwhat Dem funky pup subs, bruh. You gotta look them up. Legendary subs

[@VisionSoundPDX]

I’ve had a few BNIB amps, decks and receivers with the same RCA issue. Happens from time to time with mass produced products.

[@glencalhoun9544]

I had it happen on a nos 90's era "Power Acoustic" amp.

[@FrowningFathers]

It would be nice to have videos that test and rate the sound quality ie. THD. We always focus on the power but their has to be good, better, best for actual sound quality. I’ve heard ETON has 200w amps that boast a THD of .0001. I really don’t know what that means but it would be nice to have videos just like these but focused on quality. I’m sure the Hi-res audiophile community would appreciate it. Thanks Big D!

[@Pete.across.the.street]

THD alone doesn't really tell e anything about the sound quality of the amp. But that's what these tests are doing, testing how much power before distortion.

[@JasonWW2000]

The big problem here is that the equipment to measure distortion levels tend to cost around 40K usd. Only the big audio companies have them. No way Big D is gonna get one. THD refers to a deviation from a perfect sign wave or the difference from the input sine wave to the output sine wave. Clipping is where the tops and bottoms of the wave start to flatten out and is a type of distortion. Sometimes the wave can be offset a little which is hard to see on an oscilloscope. So there's lots of ways a signal can be distorted. Different amp companies measure the THD at different frequencies and ohm loads. That Eton you referred to measured 200w at 0.0001. If they allow for a higher thd the power might go up to 250w or higher. Some amp companies might measure power at really high distortion levels (20%-30%) to show a bigger power number. We see this on headunit power ratings a lot. It's a bit debatable as to how high a thd is too high or low enough to not hear it. The machine Big D uses is made by Tony DeAmore of Rockford fame and he chose 1% thd to be the certified output power. I don't know if 1% is an industry standard or just a commonly used standard. 1% is usually considered fine for automobile use. Home amps might use a bit lower standard like 0.5, 0.2 or 0.1%. Its all very technical, but usually distortion increases as power increases. It can be pretty clean up to the point the amp is under a lot of stress and then it will usually climb pretty quick. Automotive subwoofer amps are said to be "okay" sounding up to 10% thd. The uncertified power rating is a clipped signal that can vary from 5% to 10% distortion. For a mids and highs amp you definitely want to use the 1% rating. The Hi Res certification doesn't really deal with the thd, it's about higher frequency ranges (playing up to 40k hertz) and higher sample rates on the music source. Thats a whole other deal. I would imagine anyone making a hi-res certified amp will make sure the distortion levels are quite low. Anyway, hope that helps. 👍

[@michaelbaldwin8869]

Can we see the 5ch amplifier

[@AraceaeFanatics]

For the price, this is a great buy. AAMP did a great job with these.

[@chestermejia321]

I love your channel and all your videos. Thank you for doing what you do. I would really love to see those Kickers really jump. Maybe do a video of really powering them.

[@wal]

The JBL A6000 gave them a beating - kzbin.info/www/bejne/fpq0dYCXp95oldE

[@ricktroxell6448]

Done and done my friend always love this channel it has guided me to buy several amps and recommen several others this was the first channel i found that did amp dynos and thank you tor your time i wont buy an amp before i see you test it out or one simaler

[@Balancinglife]

Please review the XED 600, 800, and 1100 watt cerwin Vega amplifiers monoblock. Looks to be budget bangers ! Thank you for your videos. 😊👍

[@boomsiesmurf]

Great review again...hoping to see a review of the Brazilian style crescendo amps...especially the symphony s1v2 bass amp

[@thisdayage7997]

i just got the 700.1 running a Memphis MM 12 @2ohm so because of your review on it i know im pushing 550wt and im very pleased! my next build will incorporate the 2000.1 and run it at 4ohm for cleaner sound too dual 12in subs not sure the speakers yet !?

[@jermainephillips5179]

Thats impressive for the size and value..

[@AMurph79]

Dude seriously looked like Dr. Evil toward the end at like 12:45. LOL - great video as always.

[@girthquake9655]

You're impressive Big D!

[@majorbarnes4090]

I bought the MT 2000.1 a few weeks ago. I am about to do an unboxing video soon. Make sure you like this video.

[@RobertKilner]

I bought this amp the same day I seen your video and I love it.

[@ruikazane5123]

Gosh dang it did well! Unfortunately, with where I am it won't be cheap either way...

[@rockett68601]

when you are level matching the gain you need to have the bass knob turned to the max. this is where you are having problems with the remote bass knob.

[@troshaffer4921]

I saw 4k @ 1.6ohm 😮 i took a screen shot shot(right at 9:10 or so. 4002 @ 1.6ohm. Impressive amp👍

[@mcnairdn]

Could you make a list of amplifier efficiency and rated power? I am looking for the best power I can do with my stock alternator.

[@JasonWW2000]

Any of the class d style amps should be fine. If you want to save power, lower the sub level or play songs with short bass notes as opposed to long, sine wave style bass. Sounds silly, huh? Your really overthinking things. Music is dynamic and different frequencies will have different ohm loads. So efficiency is going to jump all over the place while playing music. Instead of looking at efficiency in the amp, I'd recommend looking for it in the sub and enclosure. That will have a way larger effect. A ported box over a sealed box is going to be much more efficient. Two subs over one with the same power will have higher output. So I think your looking for efficiency in the wrong place. As long as you don't use a Class A/B amp on the sub, you'll be fine.

[@matmichalke5734]

I'd really love to see the Dyno of another small amp rated in the 2k plus category, the Wolfram O2400.1

[@imfrom210texas]

The O-5K model did rated on a dyno

[@cafe80s]

Another great amp Another awesome video Thanks!

[@Bassotronics]

Pretty nice amplifier! I’m surprised the RCA connector issue it has. I’ve also owned a bunch of amplifiers and I’ve never had that happen to me before. Shout out to Big D!; subscribe to him everybody! He makes awesome car audio test videos!

[@bdc211]

wonder how he fixed it????

[@johnrambo4581]

@@bdc211 I wondered same but only thing that comes to mind is a drill bit lol

[@tacutn6]

Anybody figure out the rca issue

[@onesikm3]

I wonder if the rca jack being tight has anything to do with my recently purchase 6000 series rca wires feeling way too loose on my kicker amp 🤔

[@Charles_primetime73]

Would you do a vid of this amp strapped? I have the 2000.1 and extremely happy with it! I'm thinking of getting another one and strapping.

[@BigDonJuanRon]

I’m getting the sealed MTX Dual 12” Terminators. Should I get 2000 watt to provide extra power to offset natural lower volume of a sealed box? Subs are 2ohms. This amp is 1ohm, right? Will it still pair well with subs? Thank you for anyone that replies

[@enriqueidy8]

I got the 1500 watt one very happy with it nice clean sound i currently have 2 12 Hifonics THW12D4 Zeus Theta they're supposed to be 500 watt rms 2.5 inch coil each so total 1000 rms both about those i wonder if its real rms rating on the manual doesn't give you too much information like there is no frequency response info, so far they've been good but im not going too hard on them i dont have a meter so no idea how much power is going into them they're in parallel running at 1 ohm

[@JasonWW2000]

Remember that the 500w sub rating is a thermal power handling rating. So 500w continuous and it should be able to dissipate the heat. Depending on the enclosure, the vehicle and what frequency they are playing the ohm load is going to vary a lot. The amp may never even see a 1 ohm load. The box rise or impedance rise is always going to be higher than what your DC resistance meter reads. If you want a rough idea of the power its producing get a DC amp meter and clamp the power input wire. See how many amps its pulling. If its pulling 80-100 amps you might be getting a real 1,000 watts.

[@stephenwhite5444]

Id like a review of their 1000.5 to know if it has good sq on the 4 channels

[@joshholden8561]

Big D I have a question about how u test ur amplifiers on every amp Dyno do u set ur gain to match your voltage on ur rca outputs on the head unit? Thanks.

[@JasonWW2000]

The AD-1 uses a special setup disc to set the gain. Since it needs to measure distortion it requires the gain to be set higher than you would in an automobile. Are you thinking the writing on the amp end cover is going to be accurate? Like a gain knob saying 4v to 0.2v? The minimum and maximum might be accurate, but you can't say that half gain is 1.9v. It doesn't work like that. Those printed numbers can and usually are inaccurate. If your looking for advice on how to set gains, for mids and highs make sure they can play loud enough, but not so much gain that your noise floor is annoying. Keep the hiss down. When playing music really loud, listen for distortion or a smell from the mids. If that happens, you've got the volume knob too high. Turn it down a bit and let them cool off. Sub amps are tricky, I always set the gain high so I can reduce them with the bass knob. Again, set them so they can play loud enough and listen for distortion or mechanical noise. Try to get a sub amp big enough that your not maxing it out. When you max out an amp it can output a clipped signal and that can really heat up the voice coils. Lots of people burn up subs by feeding it a clipped signal.

[@ganeshnarayan5505]

Big D Wiz I always give you thumbs up Before i watch your videos love the stuff you put out .

[@dayvid_rrola]

Its around the same price of the skar 2000.1. Which one do you recommend of this two??? Thank you in advance

[@Whoisdissis]

Thx for Video. Just upgrading my Truck System, bought this Amp & (2) Rockville 12's Subs Destroyer, what are your thoughts or opinions, I'm a Rookie, go easy.

[@csj9619]

Great choice on amp selection, got one myself. The Destroyer subs I have no experience with, but they look the business.

[@CL-yp1bs]

Such a crazy good deal!

[@Stifodne]

Replaced a taramps bass 800 with the stinger mt1000....night and day difference...sound quality is great

[@JasonWW2000]

Taramps does have some strange preamp sections on some of their amp models. It can definitely alter the frequency response.

[@hazepheno925]

Car Audio (and some home audio) is really one of the few 'industries' that have decreased their prices while getting much more efficient and powerful.

[@GrandConception]

"I kinda work for you people" 😂

[@miomejia606]

Mine didn't have any problems with the rca cables

[@PhobosPlace]

great video, the amp seems like it puts out some good watts. i will stick with my down4sound JP23 V2 tho.

[@cj7rubicon]

I am still amazed you can hold a 2000w amp in one hand. Im used to the size of the 90s amp. Old school.

[@christianperalta1043]

Was wondering how can I connect this amp with 4 4by6 speakers in a truck? Any information will help.

[@chuckd9007]

Could we get some tests at 15.8v. Stinger makes some monster caps with adjustable voltage. Ran my trantula 6000.1 for years at 15.8v

[@off-gridoutbackaustralia]

As someone who lives off-grid and creates all there power from solar it doesn't make me feel all green knowing the efficiency of the amp but I can guarantee you I'm looking for a very efficient one LoL 😂

[@nanceeleana]

I have noticed a lot of these amps have the same layout, is there a copyright on the layout design? Plus I would love, if you can find one, to see an Esoteric amp from the 90's be tested before they sold the design to Diamond audio.

[@dlopezchampion8054]

Would you recommend this amp for a 4 stack audiopipe sub. 12". I had a 1800 Watt audiopipe mono amp and it burned out😮

[@superchile9640]

I have the 5 channel. Will you test it? I’m just curious

[@ldohrnintenful]

I've been running this 2k amp for about a month. I'm running lithium on stock alt, voltage sits at 14.4 drops to 13.5. I'm wired down to one ohm to 2 sa15s. This amp get so hot it's crazy. Not sure what's going on but I'm pretty sure it shouldn't get this hot.

[@Mr70hemi]

Hi Big D, It would be nice to torture test these Cheapo amps..They may work for your short test periods. but what about after 24 hours ?

[@drrckhamilton]

Buy one, test it, and let us know 😂

[@Mr70hemi]

@@drrckhamilton buy what?

[@deecee-EKOSI]

Old four square cubed looked bumpin 😮

[@jamiegreen4227]

Got a question how can melt a power to your amp if its to small but you can put that same amount of power from your amp to the sub through a really small whire

[@fabiancastillobenito8372]

Quiero mover dos status 1202 de 600 rms cada uno? Esta los mueve relajada?

[@jhenry48809]

So I'm still using an old amp with protection and fuses and while watching this I realized the stinger doesn't have fuses. Are fuses obsolete on newer amplifiers at this point, or is it just a cheaper amp designed without to save cost?

[@JasonWW2000]

It just depends on the amp company or the amp designer. Some have integrated fuses and some require external fuses. Possible reasons to not have on board fuses might be cost or lack of space. Its a very arbitrary thing and has no real reflection on the amp.

[@Psy6o]

Would you go with tho recoil 2500 or this one?

[@jonhouse7962]

What size fuse did you use on this amp? They say 200 amp but I see you have more amps going to the amp.

[@basscube5]

I have one of these Stinger amps on three type R 10s in 4cu ft net ported. It's ridiculous. Highly recommend.

[@joshvalentine226]

Question big d I have the 1000.1 powering two hydro ct sounds 12 they are 500 rms and the amp is 1024 rms. There wired at 1 ohm and I have everything cranked including head unit. Are the CT sounds subs underated

[@killerrush77]

this is amazing for the price