THIS 347 STROKED COUPE HAD ME LOOKING CRAZY......

[@Jay-zk7xk]

I completed my 302 / t5 , full wire harnes , fuel tank , fuel line swap in one month because of brew2l. Whatever bugs i had he covered and now I’m rolling . Thanks a lot

[@BREW2LFOXBODY]

Thanks brother, glad the videos helped 🙏

[@dougfa3515]

That's awesome! Tear those streets up!

[@xanris74dj]

Wow i needed someone like you about 15 yrs ago.

[@markcoddington2062]

Crawford 347 Stroker motors were handing out A** whoopings back in the Day in South Florida.

[@angry408w7]

Those wires loose are a very rare find. Unless they've been previously removed I'd inspect the rest of the harness. A code dump would've found the problem quickly. Don't trust the factory tach. Usually off by a couple of hundred RPM. Get an advance timing light with a digital rpm readout. Thank me later. Also go over the grounds. It's always the first thing I do to a mustang that's been "touched". Keep it up my man 💪👌👊 great videos!

[@hotrodray6802]

dial back timing lights sux. As simple as they should be, even expensive ones seem to be way off. Mark your damper with a tape etc. read directly.

[@ronniespivey4076]

Wow!! That sure brings back memories of my red ‘91 notch!! I remember spending hours when no one was around getting it to run like I wanted!! Really miss those days!!

[@bamaz7140]

Really good and in depth video. To be honest I thought the iac was bad itself. You took it a step further. Good job man. I have said it over and over again. Best mustang channel on KZbin.

[@thegeneticmachine270]

I’m a simple man. I see a brew2l upload, I hit the “like” button 👍🏻

[@ralphsbraccia2050]

I bought a 89 notch a little over a year ago and the car definitely needs work especially with idle control problems these videos are really going to help me out a lot! Thanks! I really appreciate these videos!

[@paulritchie8873]

i would send my car and my checkbook to this man if he'd let me.. Wish someone like him were anywhere near me.. Love the vids..

[@91frankenstang23]

Clean car! I’m gonna start callin you the “foxbody whisperer” lol.

[@BREW2LFOXBODY]

Lmao 😂

[@marcosolivo2606]

You can reset computer quicker, just unplug batteries then turn on headlights and tap brake pedal. This drains capacitors and resets computer

[@hotrodray6802]

Velly interesting

[@elmostong1865]

I have a buddy going thru this issue, definitely gonna send him the link to this Video, thanks Brother!

[@reeseb9768]

Thanks Brew2L had idle issues few weeks back watched ur video and did idle reset and found out iac was bad replaced it went thru steps again she's shittin n gettin again!!!

[@FromxAxDig]

I just subscribed, because you did great on explaining the issues. Glad to see a real gear head on KZbin

[@Riffs_Garage]

When doing a base idle reset you need to unplug the IAC, spout and tps. The reason for unplugging all of them is the ecu will still control the idle with any of those plugged up. Also fuel pressure needs to be 38-40 with the vaccum to the regulator unhooked when using stock or Ford racing injectors. And that bypass hose they had going from the air tube to the intake was a huge issue. But hopefully you got the wiring issues straightened out

[@iginogasparini3369]

Baro map is the issue

[@jpp9846]

Nice lending you hand to this guy👍 Them one piece headlights tho...😷

[@robertelee6712]

I'm intrigued. I want to know the problem with the car. It's killing me. Damn it Brew2L. Lol

[@bryanroupe8646]

I can't count how many cars I have bought with "347 stroker engine's." Unless you have receipts or pictures I would never take it as truth. I had a 342 with iron Sr. heads but, I would say a stroker with stock 302 heads is unlikely, even the gt40 heads. But, you never know.

[@deebo_srt1513]

Bryan Roupe I don’t think this car is a 347

[@bryanroupe8646]

I doubt it. I mean why would you spend $1500+ on machine work, the kit and then put $100 explorer heads on it. I mean someone could have bought the short block and threw it together but who knows.

[@HammerHeadGarage]

Im running a 331 stroker with gt 40p heads in a 1984 ranger.

[@erikturner5073]

I agree. GT40'S are not the greatest. I'm running World Products Windsor Sr myself. Some of the best heads out. Plus I like the cast iron heads myself.

[@hotrodray6802]

@119+ gt40 heads fully ported....

[@chadbrattain7185]

Damn that pony sounds good!!! I have a 91 lx 5.0 hatchback that I've built up with my sons and it's a beast at 654rwhp. But I've done all I want to it but I just bought a 92 lx 5.0 notchback that we're wanting to stroke it to 347ci. But I've never stroked an engine before so I need to find someone that has the knowledge and is able to help us with the process.

[@jason91205]

What all suspension you guys do to it to support that? Thanks

[@mattfarahsmillionmilelexus]

A good old fashioned diag goes a long way.

[@sammymendezjr1864]

Love these trouble shoot fox vids . Keep up the good work . 😎 keep them rolling.

[@jrh0369]

Damn dude. I wish you were neighbor. Need my 93 Cobra worked on.

[@BREW2LFOXBODY]

I’d help you out brother!

[@joshuadavis862]

@@BREW2LFOXBODY do you know anyone or a dealership selling an 04 cobra

[@ryang9425]

LMAO I have said this same thing. I'm in Charlotte NC so maybe I can get my car over there lol

[@wesboyd7416]

I’m gunna go out on a limb and say that’s just a 306. Not to bash the guy but there’s no way someone is gunna build a 347 and choke it out with gt40 heads. Hopefully y’all get it figured out and get to enjoying the car!

[@brettfrimmer6567]

Gt40 parts on a 347 is a disgrace lol trickflow all day

[@hotrodray6802]

correctly ported 3 bar heads can flow 200+.

[@prolinews]

Sometimes I look at my carburetor on my 89 and hate it and then when I see stuff like this I love it again lol. I have sniper efi on my 85 and probably going to put edelbrock proflow 4 efi on the 89 .

[@hotrodray6802]

A9L system is the best, tuneable, forgiving

[@mauricebattle978]

Someone made a plate that goes in between iac and throttle body. You can find them on KZbin it's for a 347 stroker I can't remember the name because I need one! It has two adjustable screws I believe American muscle. Hope it helps. Sorry!🤔

[@ilike9s]

lmr.com/item/LRS-9939A/1986-93-Mustang-50L-58L-Idle-Air-Control-Iac-Adjuster

[@mauricebattle978]

@@ilike9s thanks!

[@drjohnsonhungwell5115]

Maurice Battle My 89 has that plate don't know the make of it but I have a pretty radical cam and a good smooth non rolling idle even with AC on .

[@LiquidSSSnake]

That plate was an official Ford recall "fix", if you took your car to the dealer they'd put that on. I used to find them in the junkyard on all kinds of Fords.

[@jennymann3704]

I think that's the nicest thing to ask.....how's that car running. I had a police officer ask me one time I still remember and appreciate that stuff.Thats an awesome coupe.

[@RobertSiwik1968]

What a beautiful car. I can't wait for the follow up video.

[@cleetusvandame]

And one of the reasons I decided to purchase a bone stock survivor 89GT. Nice to buy one modded but then you deal with this sort of shit and keep chasing your tail not knowing what's been done to it. Stock untouched is the way to go and the way mine sits.

[@drjohnsonhungwell5115]

Mine has a plate that is between IAC with 2 adjustable screws and it works I have a radical cam and it idles smooth even with AC on doesn't idle up and down or cut off I believe LMR sells them.

[@6bt_str86]

I pushed "send" at 3:00 so you kinda touched on it

[@jm22969]

Be honest with me here lol, just how much do you hate those 1 piece headlights!?!?

[@brapperdan]

Frosty_Silver_Fox 91 they are the worst. Man I fucking hate them. Such a nice car. Just put s new set of oem headlights with clear corners and your good

[@twportre8809]

I love one piece headlights. Beats having to buy shit 6 times, many legit styles and look fantastic. Every fox out here has pretty much runs 1pc lights. Let's be honest here... It sure beats watching someone order and install Euro's on their AMERICAN muscle car.

[@johnpatillo5203]

I hate them alot

[@kennethmoyer1980]

I think we all hate them!!

[@jc-qc3yu]

Beautiful car ! I would just get a brand new management system for that car and be done with it ..Pro-m Racing sells a beautiful system comes with everything . take the old crap out and put brand new stuff in and never look back and it comes tuned right out of the box Check out late model restoration they have it

[@hotrodray6802]

viva la A9L

[@braquemathson1991]

Part II please and thank you!!

[@jcp7776]

You are making me buy a mustang!!! Great video

[@thomasgadsby4340]

My small town was just invaded...by newer mustangs..1 91 the rest all new...buggers should have let us other mustang drivers know they were comming..we could have filled the walmart parking lot with all mustangs..

[@gchav002]

Thumbs way up my friend

[@reddread4375]

You the fox body doctor for real !!!

[@styga1969]

Hook up the super star 2. Always check for codes first.

[@1calvin]

Good cliffhanger 😁

[@twportre8809]

This video reminds me of my SN95(99) I picked up a couple days ago... "Makes 400hp" ... Bone Stock intake with half the serpentine belt missing and a 1pc custom hackjob welded exhaust

[@nitro7795]

if that's a aftermarket idle control throw it n the thrash ive all ready been down that road..get ford oem please lol

[@joeruiz9029]

Great video with some great diagnostics work. My ‘85 Mustang Gt with an auto has been parked for about 15 years. I’m trying to get it back on the road but need a lot of info on those CIF cars. Was wondering if you or any of your followers had any info on modifications that can be done on this auto Mustangs.

[@BREW2LFOXBODY]

Thanks brother, outside of a shift kit, or converter I’m not that up to speed on autos

[@joeruiz9029]

Thanks

[@joshburns4177]

I always thought when you run a hot motor in these fox bodies you need to get a tune for the stock ECU?

[@demongt9186]

Off subject, did you ever get the t shirt thing ironed out with the red looking pink?

[@mtnbos]

I was having the same issue with the idiling, I replaced the computer and it was fixed.

[@briantipton8510]

I'm having a problem with a 93 5.0 surges when stopping and occasionally goes dead when you're slowing down and push the clutch in, I've done everything

[@slowbra94]

I had a similar issue with my 95 cobra. I replaced the cap and rotor, wires and plugs and that pretty much solved it. Not sure if you've checked yours but that was my issue. I was freaking out worried about my fuel pump or something serious when I should have started at the spark to begin with

[@jason91205]

Hey Man I had same exact issue with my e cam car. The car already had the iac adjuster on it. I adjusted on that and now it doesn’t stall when I’m using my ac in Atlanta heat! Lmr sells it and it actually works! Recommend it for you. No, the idle won’t be dead perfect but I don’t think they ever are once you put a cam in with stock computer set up. Good luck.

[@derpyy4577]

My 331 stroker sounds wayy beefer then that 347 stroker. It sounds like a 302 stock

[@ricardo340]

OBD 1 hell, I know it well. Holley looks better all the time. 😃

[@fordtechlife]

Good video, real life process of elimination will always get you there eventually and a box of known good parts lol 🔴🇺🇸🔧👍

[@joseguerra3989]

Man that is one nice mustang

[@roygustafson7729]

Alabama.. Gimme The Beat Boys 💪😎👍🍀

[@shawnlibby675]

Ur good with thouse foxs

[@kattdog20]

Looking for aftermarket radiator mounts like this where did cliff get these. Factory ones don’t work well on mine with 3 core radiator

[@feellnfroggy]

my guess before vid is over, no thermostat, or bad temp sensor keeping it in open loop.

[@feellnfroggy]

wiring in a fox, whodathunkit

[@stanggangchannel]

When are you going to post the second video on this? Want to see what you figured out

[@buickkkkkk1]

11:47 they call that shot gunning a problem wear you just through parts at it in the aircraft industry, Maby they call that the same in the auto I don't know, but trouble shooters are born they not made home boy is a good troubleshooter.

[@347foxmarcus90]

This is a great video I really need help with mines

[@95turbostang21]

Sound like IAC. Spoke too soon before watching video

[@DubSvt-zz9tb]

Any 5.0 mustang with aftermarket anything especially a cam is gonna need a tune or a chip etc

[@123ewq]

You seam to have a lot of experience with these sbf’s, have you noticed any real world oil consumption issues after quite a few miles on these 347s? Building a motor now for my 67 mustang can’t decide to go 331 or short rod 347

[@jaymartin5434]

Isn't fuel pressure supposed to be around 50 psi

[@jacobbales3692]

Love that car i had a 90 in 91 5.0

[@mallo6949]

Well can't get that 12:43 back of my life 😔

[@SantiSpeed1]

Did you guys ever get this thing dialed in?

[@fernandoguevara6084]

Can you do the same reset on a 95 cobra?

[@downhilldaddy9346]

Sounds more like a vacuum issue

[@springwoodslasher79]

Never buy a car when the guy can't prove what has been done with receipts. Anyone can say yea it's a 347.

[@bunnell6335]

Yeah I got hosed on my car. Dude said it had a cam and rockers and everything done to it. Everything was stock but a x pipe and rockers. (Idk y just rockers) anyways, I drove it about 200 miles or so and now it’s being rebuilt

[@elainejansky7904]

excellent " investigation " work .

[@ivorwm2291]

My 88 GT is giving me the blues. It's so frustrating.

[@WinZard]

ya mine too.... :( just don't have the time to work on it.

[@pascalolesen5187]

I took out the mass air sensor in mine and cleaned the wires carefully with a tooth brush and mass air sensor cleaner and my car doubled in power! I had high idle and off idle power issue and it went away

[@southkingscustom9241]

Nice car.

[@pimpovic2]

What ever happened to this car? Did it get straightened out?

[@frankgonzalez6872]

What do you recommend for after market fuel management system for a modified 5.0 stroked 331 . Aluminium heads (AFR) 75mm tb super charger 40 lbs IJ . Had stock ecm chipped but still won’t run right.

[@dougsadler5923]

What was it? Acted like a vacuum leak or iac wasn't working at all

[@dougsadler5923]

I know I'm just seeing this one

[@Omararmendariz9565]

Trying to be alot like Foxcast Media? LMFAO nice cars tho man. Im jkjk

[@BREW2LFOXBODY]

I’m just trying to be me🤷‍♂️

[@Omararmendariz9565]

@@BREW2LFOXBODY im jk brother. Love your videos man. You might he even bigger if you have a some1 coming out from Fl!!! Definitely got a new Sub!

[@WinZard]

needs that bama chip removed lol Just kiddin….. or am I?

[@stevend.3508]

Its hard to call it a stroker with only 347 cubes compared to other engines.

[@msk3905]

??? What you talking about do you know what a stroker actually is?

[@chidrole]

👍🇨🇦

[@dominickbono477]

too many after market parts that's why it runs like that...

[@eellis9648]

I wouldn't buy anything from these people.

[@davidgray9292]

almost 13 minutes of my life wasted.

[@BREW2LFOXBODY]

I’m sure

[@2clicks2theright375]

No way that is a 347 stroker.. especially if it has stock heads on it. Beautiful car tho

[@nicky192000]

That dude drove all the way from Florida? The word is getting out BREW2L, you the man! 🦊

[@miketheplumber448]

Really? With no a.c.?

[@scarface9617]

the 347 is nothing but nasty in these Foxbodys, very sharp ride! Nice of you to help a man out Brew2l! (🤝)

[@BREW2LFOXBODY]

I agree! Love the 331/347 strokers in these cars 👌

[@svtpower03]

Hopefully it really is a stroker. A lot of people sell these cars and say that but are full of crap. I wouldn’t put cast iron gt40 on a stroker motor.

[@jojog8304]

svtpower03 easiest to check is a computer mod (piggyback, etc), you need that to get it to idle like stock and run hard at 6000rpms. Ask the owner to change the computer engine size to 302 and watch it not start/stall.

[@cashmoneyv197436ify]

Hey Brew what do u setting TPS what do u set ur volt meter on 2 check the tps settings! That is a beautiful notch it looks like a very clean car! Yeah Brew if u get a look up the 2019 let's make a wish boy had a heart transplant! So let's make a wish contacted American Muscle the boy was 17 the car was a 1983 V6 Mustang all he ask for was a paint job in a new top so American Muscle did work on the car brand new 2015 crate engine they put a 85-86 front end on it keep it a 4 eye they did so much work really good parts Maximum Motor sport complete k- member in Kooks headers & X pipe Dakota gauges but for like a 86 set up ! U can look it up it's on You Tube 2019 let make a wish well the boy wrecked the car with 335 miles on the motor all the parts the guy up here who I buy part's from he ended up with the car Mike's Ford Part's Colora, Maryland its on Facebook if u want to check the car out the whole ass end was twisted bad! I think it was way 2 much power for a 17 year old kid they could of built a 331 or 347 but they went the big modular motor! But check it out it's on You Tube 2019 let's make a wish 1983 Mustang build check it out if u get a chance 335 miles on the car in total it! He is selling the motor in the computer stuff for $6500 brand new motor it had Baer brakes around the way around the car it's crazy the guy who I get used parts from ended up with! Sorry so long man & what do u set ur volt meter at when u check ur TPS?

[@ronnielowther2242]

Damn man it's starting to look like a foxbody convention in your yard love it do me a favor and take down that ugly Bama flag lol go dawgs sicem beat Notre Dame 💪

[@BREW2LFOXBODY]

Lmao 31-17! 🐶

[@tatersmith9544]

Yes sir !!! GO DAWGS !!!

[@GearHead704]

Can't wait to see a ride in it. Sounds great though!

[@VidTubeWatch]

That was very nice of you to help him out. I can't wait to see the finished product in the next video or so. He got him a good one for sure!

[@dangerousfreedom4965]

I wish you lived next to me brother.👍

[@rmr046]

Get yourself a real camera.

[@RoGuExPaNcAkE]

I’ve seen people buy “built cars” and the previous owners were jipped by the shops supposed to build em.

[@jivaniraya9653]

Florida heck yeah! You known down south!

[@dickiecornwell7262]

You are a special person helping people with their foxbodies you explain right down to the details that why you channel to me is the best keep the video's coming thanks for them brother

[@nitro7795]

hey brew2l I had an issue with throttle body I got off my sons 93 lx it worked fine on his car but don't know how lol but on my car it did some crazy stuff it took me n some friends several months to find the problem I would love to give to u so u can show ur watchers...let me know.

[@aldavis8266]

347 heads + intake + cam = stock with B CAM

[@justinkerrrigan6372]

Alan Davies shitty combo imo...

[@pimpovic2]

A great looking car no doubt. Still can't believe how clean that engine bay is. I'd love to see some mesh wheels with some lip and a 1/2" lower.

[@6bt_str86]

Another thing 5L 's like is more fuel pressure than what base fP is called for.

[@FastFixYouTube]

Great video and kudos for the good guy help you’re giving to people in need. That’s awesome. Many doubting the 347/iron head stroker, but there is that after market harmonic balancer. I have GT40 3bar heads and intend to stroke the motor too. Sleeper stuff I suppose. But eventually add a turbo. Heads less Important to me in that scenario. Just my two cents.

[@black88lx]

Awesome diagnosising brother 💪 Side note. If that’s a bbk Fuel pressure regulator. Throw it out lol. Throw out the bbk intake too. 😂

[@StLMikie]

Little brother to my car.

[@kgabs6090]

Check pcv system. Unmetered air?