This video will make your Life easier. Copper from thin Wires, quickly and easily in just 8 Minutes.

This video will make your Life easier. Copper from thin Wires, quickly and easily in just 8 Minutes | 3 Mega ideas.
With this Knife, you can remove the insulation from Copper Wires in just a couple of seconds.
Top 3 Best DIY Wire Stripping Knives.
How to Quickly Strip Copper Wires without Tools.
Best Knife for stripping wires | Make it in just 5 minutes.
How to strip insulation from any copper wire in 5 minutes. The best method.
#copper #stripper #cable
Best Tool to Clean Copper Wires from Insulation.
In this video I will show you how to make devices for stripping copper wires and cables, this machine will help you easily remove insulation from any copper wire,
You can make this machine with your own hands, easily and simply from almost improvised means. This is the simplest cable stripper and you can easily clean large quantities of copper cables in a short time. This is the simplest machine for cleaning copper wires, even a child can make it.
__________________________________
How to make a copper wire stripper, how to make a machine, a cable stripping machine, a do-it-yourself machine, how to strip insulation from a cable, how to strip any copper wire, a cable stripper, how to easily split a cable, a stripping tool, manual cable stripping machine, copper, how to clean copper, how to burn copper wires, copper wires, copper cable,Copper, how to burn copper wires, copper wires, copper cable, how to strip insulation from a cable, how much you can Earn, non-ferrous scrap metal, handing over scrap metal, searching for Scrap metal, how much you can earn by handing over copper, how to strip a cable, how easy it is to cut a cable, copper, a lot copper, how much is a kilogram of copper, where to find copper, medi,

[@user-xz7nb7qs3x]

Big wires are easier to strip. Small ones are the problem . Very smart way for small cable striping. Thank you😊.

[@StoicRipple]

Genius! Genius! Genius! I was using my fingers to keep the wire in line. Gonna try this soon as I get back to the shop.

[@idontknowmyfirstname69]

Brilliant... So simple

[@bormatnor]

I for one love it, simple and functional and adding or subtracting washers for spacing is a simple fix.

[@CopperKing]

Thank You

[@prisonersforprofit]

or you can just change the angle of the knife for minute differences.

[@m.weston7114]

So every time you change to a sharper blade, you drill a hole? Why not make a blade clap that you can just keep moving the blade forward by loosening a bolt?

[@ezequiasjonaslima384]

Top não vou perder meu tempo, obrigado irmão 💯👍👏👏👏👏👏👏🤝

[@shakaravaz4477]

Thanks! It's Cool! 😊

[@davevanatta1965]

awesome thinking !

[@jeffreybatts1833]

VERY CLEVER IDEAS !!!!!!!

[@bcde11012009]

Esse eu acho que foi um dos melhores parabéns pelo vídeo

[@user-yr1nb1ve6x]

Спасибо огромное за видео! Просто и эффективно, повторил, получилось! А стокими как проводами?

[@michelegregg]

In my opinion nothings to small when you broke? But very well thought out and mindful enineering, but surely would live tk see how to strip the big wired from its insulation , that would be every bit worth thw watch.

[@ScrapFatherScrapSon]

Let me know what you think. Throw him a sub and tell him I sent you!

[@martyhyatt8556]

It add up ,

[@Creativevaijan]

This guy is amazing 🎉

[@CopperKing]

Thank You

[@haluktuzunar69]

Good ideas..thanks for these video ❤

[@CopperKing]

Thank You very much

[@christophertaylor2464]

very good information I have been stripping 10, 12, 14 awg wire by cutting it in to 1inch pesice and using the wire striping plyers to bad I already cut a bunch of wire in to 1 inch pisces now I just need to finish what I started but next time I will have to check this out.

[@michealbrown5903]

How is cutting into 1 inch pieces profitable? The time it must take. Wow!

[@christophertaylor2464]

@@michealbrown5903 I am still working on stripping it . More of a little work here and then a little work there I don't need to take it in now and sell it.

[@johnr5545]

Nice job god bless

[@CopperKing]

Thank You

[@roshanbandhu123]

Very nice brother

[@CopperKing]

Thank You bro 👏🤗

[@abdulmajeedkandhro4976]

V nice

[@user-zp8el8pi3c]

If you figure you time stripping the small gauge wire and cleaning up the mess you can just sell the whole thing as number 2 insulated wire and use your time wisely.

[@benjaminbrower540]

You could flatten them to use in creating your own circuit boards. Thin plastic, cardboard.. then lay down the flattened wire. Drill the holes for components. That wire would be great for your own circuit boards.

[@red2965]

Be sure to soak them in wax to seal and add rigidity or put it into a plastic box unless you desire short circuits

[@kevinsosa1589]

Good ideas my fear is for people who aren't familiar with tools or stripping and try drilling a hole into blades like you did but it slips on them slicing their fingers up but good ideas still

[@red2965]

Most small Guage wire is easy if you start the coating and just pull you have less loss😢 especially if you go to deep and fray the wire. This is especially true for stranded wire solid wire not so much.

[@Daniel_Antonio_Arellano782]

Very good ideas. But I would rather use the one at the beginning of the video.

[@TruFrag]

Nice, only problem is the knicking of the wire. Im not a fan of getting slivers of copper 2 inches into my fingers but im also not a fan of gloves. I need a method where it just want knick

[@RolandJessberger]

I used the utility knife and washers way of doing it I have tried so many different ways and this way is the cat's ass I'm mounted it on a 2 by 4 after drilling a hole in the back of the knife and bolting it to a 2 x 4 vertically then bungee cord the front of the knife pulling it down now I can just start the school and Walk and Walk and Walk and it does the work by itself it is fantastic

[@quentonkilgore4638]

Holding the blade down while drilling it is such a good idea. Ask me how I know....

[@Ken.Kaniff.From.Conn.]

I was waiting for the drill bit to catch on the metal and start spinning the blade like a fan blade.

[@phillipcooze7668]

clever

[@vetalkzvetalkz6682]

Hello. Can you please help me make a machine for quick and easier disassembly of radiators from an air conditioner. There are copper tubes in aluminum foil. So far the easiest way is with a stationery knife... But when there are a lot of them it is also very difficult. I want to come up with some kind of machine.

[@user-bc6vk3bn1b]

Supper. Sir

[@CopperKing]

Thank You

[@adrianochoa1104]

That is so damn awesome, I have to make those kind of DIY tools to start peeling all the copper cables that I sell at the scrap yard.😊👌🤩🤯

[@user-mu5kr4gg7i]

I could have 15lbs of bare bright #1 copper stripped and done ready to sell just in the time it’s taking him to make that stuff. And I usually don’t need any tools or a knife or blade.

[@martinneps9387]

Do you sell any of these inventions that you make to strip wire? Please comment back. I would love to have one of them. Please let me know thank you for this video

[@user-ob4dw8fr1k]

Подписался, для меня на пенсии, очень даже хорошие решения!!!!

[@louisrichards3702]

and where does that copper piece with the 4 slots in it come from?

[@philipastayt]

Its from a pin chuck, or mechanical lead pencil

[@janetortiz4861]

Looks like the end of an X-acto knife to me.

[@steelman86]

You really need to mount that blade while you are drilling holes because it will chop you up if the bit gets caught and spins it around in circles!! Very dangerous! Just use a simple potato peeler to strip the coating off of the wires!

[@red2965]

Did I just watch you do a backwards drill on that blade

[@obicool1514]

I now don't have electricity in house😅

[@lazychris2000]

0:39 what kind of drill bit is that?

[@ServiciosMcGiver]

Please send me the link of the drill bit in this video, with which you drill the blade, thank you

[@CopperKing]

Unfortunately, I don’t have a link to this product, go to any hardware store and ask for a drill for tiles or ceramics, and choose the one like in the video. costs about 4 dollars

[@user-wl4vj4rh6v]

Крутое изобретение,но проще м/у дощечек лезвие зажать

[@farhanalirizvi333]

یہ مل سکتی ہیں

[@andreasilva9083]

Como faz com os cabos mais grossos , que tem duas capas ?

[@SamuelMessina-gt3bu]

Any copper wire stripped is worth the effort! You must know how to make money stripping wire

[@murlbailer3755]

Let me see if I got this right? In order to make a couple of more dollars easily I need to spend let’s say $50-$100 on equipment I don’t have? I do just fine by hand, a sharp razor blade works every time. Happy 🦃.

[@Un4inged]

That first bolt didn’t work out to well 😅

[@ScrapFatherScrapSon]

Just my opinion these wires are too small to justify the time spent trying to strip! But good informative video ! Thanks!

[@CopperKing]

Thank You 🙋‍♂️👍

[@ScrappingwithGrandpa]

I agree

[@lawrencejelsma8118]

Even if having the materials getting less than $1 per 10 minutes to video is not working a $15/hr wage job earning more. A huge amount of copper wires (155 pennies weight and volume equivalent) gets 1 lb in copper.

[@paulcoenen7918]

Not worth it for sure unless you are hoarding and waiting for the Big payday, saves a lot in valuable storage space 😀 👍

[@mattjones6147]

Hey man every little bit counts

[@DR_SOLO]

🤔 Not bad, but you are working to hard! 😉 get 2 cylinder rolling pins, or mount 2 drills to a work bench or table top. And have 2 socket drivers. Place the 2 rollers close to to each other. Then insert the three wire between the 2 Rollers, the wire sheathing will be split and go one way the wire will go the other way. Not only will you strip the wires but you will separate the wire from the outer plastic also the coating off the wire inside the sheeting as well😮😲😉🤩🧔

[@zerocool7772]

Cheers mate. Great idea.

[@randallrun]

Could you imagine the drill bit catching in that razor blade and spinning it around into his finger? Multiple times… Use common sense people!

[@jokerace8227]

I basically did that with a piece of sheet metal on a drill press, but got lucky that it didn't cut me too deep. So yeah, I'd also suggest clamping it down, just for that risk.

[@mikeoco1850]

Dude. I imagined it too.

[@danielmclaughlin6560]

Hahahaaa, dude, brah, I was thinking the same shit. Hahahaaa were not right in the 🧠 !!!

[@stihoplet_i_cot]

Я с вами полностью согласен , ваш монолог воистину прекрасен. Как вы сказали всё так и есть , прекрасны вы за смелость вам хвала и честь. Быть может вы поможете мне разобраться в информации , поступившей от плешиивой федерации. Недавно шельфовый континентальный генерал , утратившими силу свои слова признал. То есть издал новый приказ МВД от 03.07.23 номер 478 , где признаёт утратившим силу приказ 249 . И да прибудет с вами сила , как бы мразевласть не моросила.

[@jason3421]

Dude, if you ain't got patents on these things, then you better get'em quick! Before someone beats you to the punch! You're sitting on a gold mine!

[@georgedennison3338]

I can't help but think about how sore my fingertips would get after 20-30 minutes of stripping wire using these methods. Clever ideas for making insulation cutters, buy oh my tender fingers! To make stripping insulation from small gauge wire time effective for selling the copper, it has to be much less labor intensive & way faster. Best thing I've seen done cheaply was a stripper made out of the motor & belt rollers from a free treadmill. It would do all sizes & lengths & was fast. Stick the end of the cable between the spinning rollers & the copper was spit out the other side, sans insulation in the blink of an eye. Just don't have any excess cable wrapped around a wrist or ankle!

[@motopumpkin3129]

Please don't hold the razor with your finger! If that bit caught and spun the blade...

[@hieulengotran5093]

Bảng in : 144 số 0. Cr

[@user-cq5mf2cw7i]

На час в растворитель и всё не каких приблуд

[@Thomas384]

I came here after a ghana video where they burnt cables while these method works just fine, I did the same way by myself,why can't they evolve...

[@familydogg1234]

That copper ironically will cut your hand like a razor

[@hieulengotran5093]

Carve ? Who

[@dariorossetto3317]

😂😂😂😂😂

[@MohanKumar-ol3uo]

M

[@t-towntransparency8850]

It needs to be stationary and a spool pulling it through and it would maybe make money that way. But this is too slow coming from a full time scrapper.

[@weatherill430]

not worth the time spent imo . you could just burn it and mix it / hide it in with #2

[@charliehoss1614]

Lmao. Save time, after all you can’t put a price on time

[@Mayank.6250]

तू ये बता ये फालतू काम करना क्यों है नल्ला बैठा रहता है क्या घर में

[@958fuser]

...e per cavi grandi?