Hello - I've got a suggestion for the split hulls - it's only the bit of hull at the end that is brittle - just set the hulls with split ends asside in a container of some sort, then use them for short shells - 1 3/4", 2", etc. IIRC BPI used to sell a hull cutter to make it quick & easy to trim off the end. Short shells are fun to play with, but it would be a shame to shorten perfctly good hulls. I like short buckshot shells myself, they work perfectly to defend my garden from woodchucks (nature's perfect garden terminator, which quickly learn to avoid live traps}.
@deandeann15414 жыл бұрын
ps thanks for your videos, they can be helpful.
@boomerrangerron4 жыл бұрын
You should get a small bullet starter from CVA that's used to start muzzleloader bullets. Would be a lot easier than a screwdriver. I can't wait to see the actual accuracy results. Hope you'll do a follow up video with targets.
@charles12064 жыл бұрын
Your drill press sounds is running low on motor oil. Hah
@OzarkSpirit5 жыл бұрын
Dammit Dave. You are going to get me into shotgun loading.
@Thorsaxe7775 жыл бұрын
I have to go to town today, one of the things is to get those slugs off to you in the mail. I'm sending 20 of them. If you have Longshot or Blue Dot, those two powders are a good choice.
@OzarkSpirit5 жыл бұрын
@@Thorsaxe777 this is a great video to get them loaded
@svernwarunos5465 жыл бұрын
Safety squints is the way to go.
@GunFunZS3 жыл бұрын
I like using gloves with rotating machinery. But there is a bit of understanding in technique and type of glove. Context is everything.
@jamespollard16705 жыл бұрын
Interesting , but that drill press has a rod knocking with an electric motor .
@Thorsaxe7775 жыл бұрын
I need to tighten the v-belt.
@singleshot22185 жыл бұрын
What's up with your drill press? Sounds like it threw a rod! Wow!
@Thorsaxe7775 жыл бұрын
I need to tighten the v-belt. No big deal.
@electromech73354 жыл бұрын
It sounds like my 1st car after I got my drivers license 🚗😄
@Ruteger1005 жыл бұрын
where can I see your results from 100 yards? very interested. You and FC45LC are the greatest, Thanks.
@celticdude46865 жыл бұрын
Got it .Loads of Bacon is James.
@nickross1335 жыл бұрын
Hey Dave. Sorry but I haven't got to making anymore tools lately. I was on vacation the week before last and was not feeling well the first part of last week. I'll try and get something done this week.
@Thorsaxe7775 жыл бұрын
People were asking me on my show where o get them.
@FortuneCookie45LC5 жыл бұрын
Take care, Nick - Hope you feel well soon... Steve
@Thorsaxe7775 жыл бұрын
Hey Nick, do you have an idea when you will have some of your tools available? I see that your Hull vice is a big hit for unmatched quality. I know James has those in stock. Just wondering about the other stuff.
@nickross1335 жыл бұрын
@@FortuneCookie45LC Thanks Steve I'm good now.
@nickross1335 жыл бұрын
@@Thorsaxe777Hey brother. I'm gonna work on it this week. It will be later in the week before I can get to it.
@wbrewski15 жыл бұрын
Where can I get one of those priming and de priming tools. Great video , could you make a list of all the slug loads you have tried I would like to develop my own load, where do you start how do you pick a powder and a starting load?
@Thorsaxe7775 жыл бұрын
Best advice to you is to buy a manual from Ballistic products. that is the best place to start. then as things get more familiar, you can experiment with different slug/load combinations. thanks for watching-Dave
@williebulletman52175 жыл бұрын
Ok mr. Dave I have a question when you are doing that hull conditioner how long do you normally do it for to heat them up I mean is it a set time are you going for feel of temperature on the casing can you explain that please
@Thorsaxe7775 жыл бұрын
30 sec, to a minute. the plastic will be rubbery and flexible. You have to work with it, kinda like "How long do you leave the brass in your wet tumbler"? You will know when it is enough. Willie, it is just one of those tools you have to use to learn how to use it best.
@eugene78902 жыл бұрын
Do you ever do this test with these slugs and with blue dot at a 100 yards???? Also when you do this test are you shooting a fully Rifled barrel or a smooth bore?? I am very interested in this test because I am thinking about getting this Russian Svarog slug molds. Thank you for your videos.
@tommeboy33345 жыл бұрын
Slow down that drill press. The speed should be around 200rpm for the roll crimp MAX!
@Mav8887.5 жыл бұрын
Way off
@chudrustler4 жыл бұрын
looking for some input on hulls- any thoughts on Ficochi Green hulls?
@Munky3325 жыл бұрын
Do you think the Hydrants or the Paradox would be better for Smoothbore? Looks like the Hydrants have a bit of a "taper" to the driving bands, where the Paradox does not? Paradox is listed as .724 diameter for all driving bands/belts, where as the "Italian" (aka the Fire hydrant), is listed as the front side driving band being .724, and the rear driving band only .700? Is this correct?
@GunFunZS3 жыл бұрын
I finally got one of the paradox molds. James was super generous too. There's another guy on the reloader's network named m i c who wants extra heavy slugs made from that. So James sent me a couple extra pins that I can modify to fill out and make the slugs heavier than standard. For my part I think I would actually want them to go lighter but I'm not complaining. Not really sure what to use as a data source for these. I think I will trade for a lighter load of blue dot and probably WSF since that's my favorite. Any suggestions for what I should use as a data source or starting load?
@gossett03305 жыл бұрын
can you use hornady case lube on the slugs
@Thorsaxe7775 жыл бұрын
That is something I wouldn't recommend. Hands down the best way to avoid leading and provide lubrication is to powder coat. Now that is my opinion based on the results I have obtained through testing slugs.-Dave
@davehunt94274 жыл бұрын
Could Red Dot be used to load these slugs? Good vids!
@Thorsaxe7774 жыл бұрын
Red dot is too fast of a powder for this, you need slower powders, Blue dot and longshot. I would advise you to not use red dot, that would be dangerous.
@Knallhatt3705 жыл бұрын
I shoot theese in a smoothbore stoeger m3000. Very accurate. I get severe lead fouling though. To lazy to powdercoat- did the floorwax work for you?
@Thorsaxe7775 жыл бұрын
I have not got any leading in my bores, you may want to measure your muzzle size "Choke" wise and see if that could be a problem. also, once the bore is coated and conditioned with a waxy film, lead won't stick to it anymore. also, the chamber transition from chamber to barrel may be too much of a abrupt edge and that could be a source as well.-Dave
@Knallhatt3705 жыл бұрын
@@Thorsaxe777 Thank you for quick reply! The gun is quite new. Lead fouling occurs just after the chamber. Ill get me som wax then and try. What alloy did you use? Friend of mine suggested that i should go harder on the linotype to reduce the fouling. I am a little afraid of the pressure thoug, slugs are meant to be soft as i understand it. Svarog writes 3% tin and 97% lead.
@Munky3325 жыл бұрын
What sort of accuracy are you getting? I'm torn between getting the fire hydrants and the paradox.
@dennisball3673 жыл бұрын
Yes I'm wondering how can I start something like what I see on this video I love and shotgun shells and all the rest stuff who would I talk to you and how would I start
@bosweeney7195 Жыл бұрын
Where did you buy the slugs ? I can't find them any where .
@celticdude46865 жыл бұрын
How do I get a set of the Nick Ross shot shell prepping tools? I don't see them on reloadersnetwork. I love the hull vise I got. I like that hull funnel you are using also.
@Thorsaxe7775 жыл бұрын
James is handling the inventory. when nick sent these tools to me he was working on doing a production of the case prep tools. as far as the roll crimper, the ones he sent me were prototypes and he hadn't started production on them at that time. Drop a note with James and he should be able to help you out. Dave.
@celticdude46865 жыл бұрын
@@Thorsaxe777 James?
@nikovlahou25533 жыл бұрын
Do you have any load data for the800 gr super paradox slugs? Also, does using the overshot card on the roll crimp change pressures?
@bobn16055 жыл бұрын
I received my Hydrant mold and special tail wads in the mail!!! I had to order after watching your videos. What are you finding is the best load (Data) for them. Blue dot or Longshot? And what grain? Still loving the vids, keep it up. I have been watching Fortune Cookies as well.
@Thorsaxe7775 жыл бұрын
Bob, I believe that Blue Dot or Longshot starting at about 30 grains is a good starting point. the Ballistics advantage manual lists longshot for the Galundi. that slug is the same as the Hydrant slug. The hydrant slug is an outstanding projectile in the way of accuracy plus combined with the power of the huge slug any medium to large game can be taken with it.-Dave.
@bobn16055 жыл бұрын
@@Thorsaxe777 Hi Dave, I saw you had gone as high as 38 grains of Longshot. FC45LC has done the Paradox as you know and has done 34,36,and as high as 39.5 on bluedot. I saw his video on the comparison to factory. The 39.5 beat them but he said the 36 was even more accurate. I guess I was wondering what "YOU" found the best for the hydrant. Was it the 38 grain? The DGS (I have the manual from BP) is the slug that is in our Challenger FACTORY slugs. I cut one open and it is the exact slug. They use 35.5 grain and claim 1620 fps but I'm not sure of the type of powder. I did a primitive video on that and the score slug (factory but its the thug slug...exact) its on my channel from 4 years ago. My son helped out. kzbin.info/www/bejne/Z2m0i5iZatqJZ6M I will be doing a penetration test between the factory challenger (DGS) and score (thug slug) and the Hydrant once I load them, just not sure If I should use blue dot, longshot and what grain. Bob
@nigtturner5 жыл бұрын
well done dave that was a very layback informative video I really just chilled out watching Nigel from russianslugmould.com
@Thorsaxe7775 жыл бұрын
I'll check that out. Thanks. Dave.
@colinbalderston48595 жыл бұрын
Hi where can I get one of those roll crimp from .I live in Australia and never seen one.
@Thorsaxe7775 жыл бұрын
Shipping to Australia may be pricy, however, at The Reloaders Network they should be available soon. Check on the site under Merchandise.
@colinbalderston48595 жыл бұрын
@@Thorsaxe777 thank you ill look there
@jaredtaylor7683 жыл бұрын
I was wondering have your tried tite wad . if so how does it work with these slugs
@nickcavanaugh95863 жыл бұрын
are you shooting these thru smothbore full rifled barrel or rifled choke tube
@tires2burn3 жыл бұрын
Kind of like annealing brass.
@winterlounge3 жыл бұрын
Which do you like better paradox or fire hydrant?
@mikebagnallshooting98184 жыл бұрын
Hi I have found an answer to seating the Russian slugs if you want to check out mike bagnall shooting on KZbin it may interest you buddy
@Thorsaxe7774 жыл бұрын
I discovered the accuracy problem and the relationship of the wads separating when fired. I saw this on Jeff's Chanel Taofledermaus, he has ultra slow-motion camera equipment that (If someone really looks) tells the story about what happens when the slug exits the mussel. Thanks for your comment, I responded to your video and if you want, I could see about shipping items to you. Thanks for your Video dude. - Dave
@michal.abramowicz3 жыл бұрын
Knock, knock! Who's there? The rod! But, wait the moment...!?!
@garyburgess38294 жыл бұрын
Where did you get that vice that holds the shells on the drill press?
@Thorsaxe7774 жыл бұрын
Go to The reloaders network. they have them in stock.