√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@skoolgordon18103 жыл бұрын
Need to buy need to buy a throttle body for a 2000 Plymouth Grand Voyager 3.3 l engine need some help on where I can buy it
@1AAuto3 жыл бұрын
+Skool Gordon Thanks for watching! We currently do not carry a throttle body for that model.
@queenscreationsbakeryllcqu64353 жыл бұрын
@@1AAuto I just replaced my throttle body on 14 Chevy Equinox and it haven't started yet...
@spellbreaker66092 жыл бұрын
you mess my car up you did not tell us we had to pull the battery terminal before changing out the TB so the engine can reset itself to the new position of the Throttle body flange
@margiemaples48762 жыл бұрын
hi where can i go to get my throttle body relearn or can i buy the device to relearn myself
@NathanGarcia-y3g Жыл бұрын
I learned nothing from this video.
@williamsiple-np1ow Жыл бұрын
I tried the reset procedures and they didn’t work. I have a 08 Chevy Trailblazer LT 4.2L. Any suggestions? Please help!!!!
@jacovferro85432 жыл бұрын
Good morning i just replace my 2014 f150 trhottle body can you please explain me how reprogram ? My truck shake lot and loose speed
@papo8622 жыл бұрын
kzbin.info/www/bejne/kH_biYBtat99hdk
@user-im2ik9zd1w2 жыл бұрын
Replaced app sensor and throttle body what computer do I need to reprogram them
@stevealen7452 жыл бұрын
Hi i have a 2010 Honda crv Awd 2.4 I have a accelaration problem on cold engine stop /go motion .The engine hesitation ,he don t whant a move by himself he go to shut down by himself ,i have to hard press to accelarator to run,every think came to normal when the engine came normal,spark plugs are new, no code on scan no check engine light,my mechanic ean the trootle and the sensor even he change the crankshaft position sensor,nothing change,did you think its the throttle it s finish or the problem it s the gas pump,thanks
@bradrogers40194 жыл бұрын
Like the videos. Feels like we were better of with cables
@1AAuto4 жыл бұрын
+Brad Rogers Thanks for checking us out! 1AAuto.com
@tobydozier90303 жыл бұрын
Drive by wire is way more responsive than drive by cable.
@cgreen3393 жыл бұрын
I agree
@hermanrogers13252 жыл бұрын
Yep that’s right just some more stupid stuff to have to be put in the shop to recalibrate and cost a thousand dollars to do it
@kippd22652 жыл бұрын
@@tobydozier9030 bull
@johnringoo756 Жыл бұрын
Disconnect the negative cable from the battery for 5 minutes usually does the trick
@nikovandh4 жыл бұрын
I told my girlfriend I need to clean her dirty throttle body, and she thought it was innuendo ;D
@gregsmalley28902 жыл бұрын
so in other words go drive your car and it will reset itself. useless video to get clicks.
@brainwashed7244Ай бұрын
Some vehicles you have to flip over on its side and rub its belly the information I just provided is more valuable than the information that you provided but that's the way I like it KZbin watchers don't deserve anything
@kato21822 жыл бұрын
huge thanks for this video I unconsciously fixed the problem watched this video and just learned all that i did was normal thought my truck was stalling out but no it just because The throttlebody was relearning while idling for a few minutes
@hightidelowtide638011 күн бұрын
Isn't that snall hole the built-in idle air control valve?
@marywilliams53676 ай бұрын
Please make a video about and how to change the throttle body sensor.
@tomahawk59592 жыл бұрын
Take off the TBU take it off slowly try not to move the butterfly use TB spray cleaner leave it to dry over nite install an let it run don't mess with it. Power will be restored
@TwitchRadio11 ай бұрын
2003 hyundai xg350 L did a throttle position sensor and it is super rough now... not sure what to do from this point being the car is over 20 years old😂...
@dkenner17664 жыл бұрын
So after cleaning my throttle body, which I had no idea there was a relearn process, my idle is just about 600, but even after doing the relearn process when I rev it up it stays up and will not come back down. Any thoughts?
@zacharyneilson92203 жыл бұрын
I have this same problem
@arkayem713 жыл бұрын
Same problem here. 😢
@Crazycookson11153 жыл бұрын
Did u figure this out
@hermanrogers13252 жыл бұрын
Yep you got to take it to the dealership and get it reprogram for a nice fee
@tedthornton77912 жыл бұрын
Brake fluid cleaner or carb cleaner? Really? But want that be harmfull to the surfaces? I use throttle body cleaner only and a soft bristle brush in addition to a clean rag.
@mexdaman79453 жыл бұрын
Can I just clear the code on the obd scanner will that work? After I replace the throttle body
@jackstichtenoth1416 күн бұрын
HELP! Do you know the relearn procedure for a 2018 Hyundai Elantra? I can't seem to find it anywhere.
@lecobra4182 жыл бұрын
Weird advices, I wouldn't advise anyone to remove and clean their throttle body without having the possibility to reset the TB with a computer unless they want to experience weird revs issues etc. First get a computer with the proper software to control your pieces then remove and clean it.
@kellyschoers96768 ай бұрын
Can someone help me what I need to do with a Kia Grand Carnival 2012 once replaced new throttle body? Thank you
@jorgecordova61333 жыл бұрын
Hi, its safe to push the butterfly on an electronic TB? While is off and out the car. I’ve reed that the gears on the TB can get bad. (Toyota 4runner 2012)
@jasoncorganbrown11 күн бұрын
Do any modern vehicles actually require an external device to re-learn the throttle body? Or is the use of a tool a convenience thing?
@kristiankoch78104 ай бұрын
Disconnected my battery now driver side A/C blows hot and passenger side blows cold……..
@roliy_4 ай бұрын
does anyone know why after driving and lets say i stop at the red light my car idles at 2000rpms, do i need to calibrate it or replace it?
@tabithadeckelman13192 ай бұрын
I recently replace a throttle body in my Chevy Equinox and I had know idea that I had to do anything extra after that! So big thank you for this video, it help my issues such and check engine light and codes!
@Shaverboy5163 жыл бұрын
Does a MAP sensor replacement need a relearn procedure as well?
@lecobra4182 жыл бұрын
No.
@OkayAhhgain3 жыл бұрын
I cleaned my Throttlebody and did the relearning procedure. The rpms went back to normal but when in park and when I step on the gas the rpms up to 4000 and stay there. I have a 2011 GMC Yukon
@joshuadodson27573 жыл бұрын
Im having the same problem but with an 2011 silverado 5.3
@joshuadodson27573 жыл бұрын
You figure anything out?
@adrian7110f3 жыл бұрын
Same problem
@rolandomota11533 жыл бұрын
@@joshuadodson2757 did you figure what was wrong with it ? Same problem here
@danf6333 жыл бұрын
Did anybody find out the problem Have the same thing on my 2011 yukon?
@Captainpook122 жыл бұрын
I replaced my throttle body and ran the car til normal temp . Then I drove it seems to be good . I didn’t do this before and had a surge like the transmission was slipping . Hope doing the relearn corrects the problem. I bought a mass airflow sensor plugs coils and a new pedal. Not knowing this was possibly what was wrong .
@hondamuddingcrew Жыл бұрын
Did the relearn correct the problem.
@billyremmert7679 Жыл бұрын
What is electronic throttle body problems is that what causes the van to accelerate uncontrollably and jerk and buck for the brakes fail to hold it back
@LarsonFishing Жыл бұрын
My scan tool is throwing a P1101 twice, pending & permanent. P0299, P2227. Replaced the turbo booster sensor & cleaned the MAF sensor with MAF cleaner. Engine light stayed off longer than it was after all that. But ultimately came back on. So I removed the throttle body tube and noticed some light gunk & condensation bubbles on butterfly valve, So I carefully cleaned that as well. Same codes still show. ANY advice would be much appreciated. (2017 Chevy Malibu LT 1.5 Turbo) Thank you! 💪🏼
@Himithor4 жыл бұрын
My engine stays reved up/high idle when im at a stop light ao have to tap the explorator peddle to make it go to quiet idle. I have a 2001 dodge ram 2500
@OscarB214 жыл бұрын
Could be a dirty Mass Air flow sensor
@eugenew671719 күн бұрын
Will an autoparts store have good enough scan tool to reset it free?
@adriantejadaramirez3396 Жыл бұрын
So basically, every time I get the ETC cleaned up I will have to run the re-learning procedure.
@markwoten66793 жыл бұрын
I got a 2006 Kia Optima EX (Old Body) 2.4 L. I recently replaced the power steering pump with an new OEM pump plus new belt. System flushed & filled. While I had the time, I removed and cleaned my throttle body and mass air flow sensor. Car runs good but got a slightly high idle speed greater than recommend 700-800 rpm. There is no fluctuations in idle speed. Starts great… new IAC valve PO507. What is the relearn procedure for my TPS? I want to get the idle back where it needs to be.
@OscarHuluLema Жыл бұрын
Push brake in…set park brake…key on key off….start car…put in drive for 10 minutes. Now the cars fuel trim is correct
@Redmayne152 Жыл бұрын
I swapped out my throttle body (it would randomly go into limp mode with the lightning bolt and traction sensor) and after I did, it was permanently in limp mode with a worse sounding idle along with my check engine light. Would a relearn fix that? Or is the new throttle body faulty?
@stephens92402 жыл бұрын
Thank you so much recently cleaned my throttle body and mass air flow sensor. Just took me 2 hours to do a 35 minute ride here to work and I'm a couple miles away I keep stalling and I keep resetting the battery. Just went and bought a can of Lucas fuel injector cleaner to go in the gas tank and filled up and also bought a can of throttle body cleaner so I can clean it one more time and reassemble it and let it drive around 40 miles an hour on the highway like you suggest I pray it works my car is a 2013 Acura TSX special edition 4 cylinder. God bless you for all this information and I pray I get everything running great again take care. 🙏😃
@1AAuto2 жыл бұрын
+Stephen S Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
@armandoperalta41311 ай бұрын
I cleaned my throttle but now my idle is worse goes up down
@whitesirhc4 жыл бұрын
What Relearns do I need to have done on my 2010 Kia Soul 2.0?I changed the Coolant Temperature Sensor,Purge Valve,Crankshaft Position Sensor,Idle Air Control Valve,Fuel Pump & Fuel Filter,MAP Sensor,new battery,new spark plugs & wires & I have a new Throttle Position Sensor,but haven't changed it yet.I may have to take throttle body off to get to the 2 screws that are very hard to unscrew.Car is wanting to stall after driving 15-20 miles & feeling low power surges,plus a little vibration here & there.It gets so frustrating.I am just finding out that certain new parts need a relearn.What ever happened to replacing old parts with new ones?
@bangyahead12 жыл бұрын
Cost. It's cheaper to clean a part than to buy a new one.
@notuagain15 Жыл бұрын
What did it end up being
@ShiekahTribe2 жыл бұрын
I have a question - not sure if you can help. I just had the throttle body on my Polo 9N3 replaced because of intermittent starting issues (it would crank for a longer time occasionally but always start after this. When briefly switched off after this, engine would start immediately). Now I have a car that's hunting when I first start it up, RPMs going up to 1100, going down to 800 going back up and sounding like it's stalling. Didn't have that issue before the replacement. Mechanic suggests it could be the oxygen sensor - but why did this problem occur all of a sudden after the replacement?
@jon51593 жыл бұрын
I really hope this all I need to do because this is driving me crazy and not to work.
@Durangort-mn3jd Жыл бұрын
Great video 💪🏻💪🏻 I got a Dodge Durango 5.7 hemi v8 2016 I’m planning to change the throttle body how I can relearn it Thank you 🙏
@heathcalvert13193 жыл бұрын
Got a question my 99 Durango sometimes cranks & cranks then starts up how can i fix it put in a new fuel pump new plugs and wires cap and rotor and pickup coil
@ceejayc65022 жыл бұрын
Battery terminals? New spark plugs?
@wtulin19703 жыл бұрын
well, i don't really have my answer. "a certain amount of time" doesn't mean anything.
@AltruisticWarrior2 жыл бұрын
It's truly variable based on a mix of distance and how many cycles going from a stopped position to 41mph(I believe it was). If you just hop on the highway and drive at 75mph, you could go hundreds of miles and still hundreds more without it relearning. Best to do city/highway mix. In my case the only way I could fix the problem was having a shop reprogram the TPS and APS simultaneously.
@Jeremy-ts9pt2 жыл бұрын
I have an 02 toyota sequoia sr5 4.7l and cleaned throttle body and now I don't have any throttle response. Please help me I've been without a vehicle since February and it all started from having the starter replaced. HELP ME. TIRED OF WALKING
@Godzilla201682 жыл бұрын
I looked at a 100 videos for this type of explanation. Thanks!!
@JustinMentionedIt2 жыл бұрын
Curious on an Acadia 11’….. I got a P0430 which is a catalyst code but it won’t start which means it’s not a bad catalytic converter could it be the TB? Could a really dirty TB prevent a car from running and throw that exact code?
@JBrewner-lb8ek2 жыл бұрын
You ever figure it out? I’m getting a p0507. Car wouldn’t turn on. But I just had it cleaned, it ran and won’t turn back on after I shut it off. I have to do the relearn process still.
@susterostreams6 ай бұрын
i had a shop replace this and the throttle position sensor. now it idles sometimes at 650rpm or really low at like 500 or 450rpm. also when i put it in reverse sometimes it goes as low as 250rpm almost shutting off until it revs itself up to normal idle. also i was just pulling into the driveway earlier and gave it a little gas and it revved itself up unexpectedly lunging itself forward for a second before i stepped on the brake. kind of annoying
@everythingvideos24 Жыл бұрын
Save money? I bought a 12volt new battery a new $200 throttle body, and am doing the throttle relearn procedure by the repair manual still idles high.
@dennislaughery23718 ай бұрын
This video was far from educating. All I learned was that some cars you may have to do this and some cars you may have to do that and other cars you may have to do this, but with other cars and certain cars you would need to do this. Which cars do you need to do which procedure?
@thebigchicken29866 ай бұрын
i would highly recommend NOT using brake clean. Air intake or throttle body cleaner would be safer
@abdussalammuyideen81283 жыл бұрын
Please help me out. I have a rough idle when I load to Drive or Reverse. So I change the throttle body but still rough idle. How do I calibrate the new throttle? Golf Mk4 1.8L 20V engine.
@lecobra4182 жыл бұрын
Use VCDS/VAG-COM to reset it properly. Rough idle might also come from a dirty EGR valve or a dirty MAP/MAF sensor, or spark plugs and everything related to it, clean everything up and it should be fine.
@MC-mh2ju3 жыл бұрын
Wouldn't disconnecting the battery automatically RESET the idle?
@dawnrobbins58772 жыл бұрын
You would think so but I know for a fact it doesn't, at least on some vehicles.
@devinmoore9877 Жыл бұрын
Hello I have a 2007 Hyundai Sonata 3.3 had battery unplugged for a whole day while doing Engine knock sensor now car won’t crank back on could it be that throttle body stuck closed need relearn ?
@onedayatatime87562 жыл бұрын
Brake cleaner or Carburetor cleaner to clean the throttle body? Nope! They leave residue behind. I'll only use throttle body spray cleaner, or Mass Airflow sensor spray cleaner.
@kennethhood84403 жыл бұрын
Do you have to reset ecm on a 2003 crown Victoria after installing a throttle body spacer?
@johnnysonpon5795 Жыл бұрын
I Have A 2010 Ford Fusion SE. Just Bought An Electronic Throttle Body. Would I Need To Reprogram It After Installation Or Would It Reset Itself?
@pammatthews92772 жыл бұрын
my husband has a 02 dodge ram 1500 4.7 has changed every sensor truck cranks for a couple minutes then dies what do we need to do now rebuilt the engine changed sensors same problem help....
@user-cj4hk8lr1v Жыл бұрын
“It depends of the type of vehicle”? Really? That’s it??? 🤦🏽♂️
@billalderton39633 жыл бұрын
I replaced the throttle body, did the relearn procedure (2009 Envoy). Idle is now good, however, once I just touch the accelerator, the car RMP jumps up causing the car to lurch immediately. The RPM is jumping from 800 to 1200. Any idea? Again, just touching the accelerator with limited acceleration.
@1AAuto3 жыл бұрын
+Bill Edison We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@tymothyjohnson13073 жыл бұрын
Bill were you able to find out what your issue was. My brother has a 2007 Tahoe that's doing the same thing.
@ronakd.705 Жыл бұрын
Hello 1A Auto from ON, Canada….what’s the process for 2019 Mazda CX-5 GS AWD 2.5L Non-Turbo? i have cleaned the throttle body with CRC Throttle Body Cleaner and when i placed it all back together the RPMs started jumping with the throttle plate acting like it’s got Parkinsons LOL ….one of the mechanics believes after checking with a code reader ipad it’s placing pressure on the Purge Valve….please help me figure this or should i drive on the highway for a while and that might reset the throttle body or have a re-learning process conducted? thank you…🚙🤙🏼😎
@Stefan-wp3pk2 жыл бұрын
Are these error codes an indication that I need to recalibrate the throttle? Which error code reader can do that on Citroen C5-2004? P2101: Throttle controller A motor control - Circuit range / performance P1153: Citroen: Thorttle - Threshold learning fault I have already moved to a brand new throttle body
@ceejayc65022 жыл бұрын
Sounds like the sensor was fried. I assume with a new TB you got a new sensor.
@FlAvIuS861 Жыл бұрын
got a volvo s40 2.0 gasoline ...i just instaled a new throttle but when i start in the morning RPM jump fast to 2000 then back to 1000 and as i drive and engine warm up will settle to 650 any tips or is normal i mention the car will always start secound time i turn the key new first time....
@JR-kr1lv3 жыл бұрын
Doesn't say which type of vehicle it's doing for an I put in precisely Honda and absolutely nothing about hunters whatsoever so it was a wasted of my time to watch video.
@keisem7127 Жыл бұрын
I replaced my throttle on a 2012 ford Taurus and the check engine light code p2104 reads on the dash. Vehicle also cuts off going 50+ mph causing me to pull over at reduced speeds in traffic unable to accelerate…Any solutions?
@boomerguy99353 жыл бұрын
Most owner's manuals will tell you how to do this after the battery has been disconnected. Different cars do it different ways.
@c.5182 жыл бұрын
What if i dont disconnect the batt. And use a scan tool to clear a check engine code. Do i still have to do a throttle relearn??
@ronnieyoung75102 жыл бұрын
I have a 2000 Chevy Colorado it won't go on fast idle in the morning every place to throttle body and in the morning the motor shut off I got to hold my foot on the gas pedal so it warms up I couldn't be
@boobizzy41733 жыл бұрын
Thanks brother 🙏🙏 we need you for president 💯
@1AAuto3 жыл бұрын
+BOO BIZZY Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@theindustryfarm7405 Жыл бұрын
Gm 3.9l v6 will start the car and it’ll drive then suddenly after coming to a stop randomly wether it be a 5 minute cruise or an hour long drive it’ll bounce into reduced engine power. Currently trying to re program throttle position sensor took it from my other car (3.5l) it fits perfectly. But I notice rpm’s are off slightly and I have afm which activates at about 1300 rpm’s on the highway but I’m revving at about 1650 so when it de activates into 6 cylinder it’s a little harsh. Any help relearning would be great
@puleelias23839 ай бұрын
I just bought new throttle body for my audi a3 1.4 tfsi, so wanna install it, after the installation do I do the same as on the video? Turning the key for minutes then turn it off...?
@SCORP1ONF1RE3 жыл бұрын
Hi, I have to press the accelerator about a quarter of the way down before the car starts to accelerate. Do I need to reset the throttle body? Or could it be something else?
@thechongsterful3 жыл бұрын
Has hour car thrown any check engine lights or has your ABS or stability light appeared? I would check the APP sensor and then the TPS sensor.
@JBrewner-lb8ek2 жыл бұрын
@@thechongsterful my 06 Altima had similar issue, except it threw me a p0507. Drove with it for a few days then when accelerating from red light the acceleration stopped for a second then I drove another 15 seconds and it happened again while driving , not from starting from a stop. It won’t turn on now. I had it cleaned as it was dirty af. It turns on but after you let it sit for an hour it won’t turn on. The service engine light doesn’t come on anymore. I haven’t done the relearn code yet.
@jayjb8333 жыл бұрын
Have have g8 gt and it’s giving me pOO68 code !!! Just re cammed died after a 15 mintier drive and reduced engine come on
@loko26272 жыл бұрын
My 2013 express van stays accelerated , I drove it for a good 40 min and still feels like rpms are high and check engine is still on , what can I do ?
@tengzturiagaiii31853 жыл бұрын
Hi, i have a 2006 lexus rx330. I will need to replace my throttle body. But i saw two hoses.. one on the right it for coolant. Doni need to bleed that after i replace the throttle body. And the other hose on the left. I have not unplug it just yet.. where is that connected to? Thanks
@daviddart400 Жыл бұрын
I used my scanner to relearn my throttle body after replacing it but still getting high readings passed 14% what else can cause my throttle body to read high?
@timothyschneider74842 жыл бұрын
I have a 2016 vw jetta sport and I did my relearn through a scanner. Can you tell me why it forgot overnight? No higher idle on cold start. Goes directly to 600 no matter the temp outside
@mplscarsales66522 жыл бұрын
Just learned that after replacing battery in Cadillac ATS that throttle body cycles and relearns itself turning it on in acc mode then shut off then turn on ect
@fernesal Жыл бұрын
I just cleaned mine. And when I restarted it it came back normal 650 -700 rpm
@SaabLife085 ай бұрын
Not very helpful....
@jnaerussell2202 жыл бұрын
I have a 2012 jeep liberty changed throttle body and throttle pedal senor light is still on.
@tylerhurst143 жыл бұрын
This doesn't work on a 2006 Pontiac G6. Just buy a Foxwell NT510 Elite and you can reset it in 5 minutes without causing all the wear and tear putting a car in gear when it's idling too high trying to do the stupid relearn that doesn't work on some GM vehicles. A shop will charge you for a full hour of labor (about $150, the price of a scanner that corrects the throttle position sensor), unless you know somebody. You'll drive all around town looking for a decently priced bi-directuonal scanner. Just order online and plan on not driving your vehicle until it arrives. I wish I would've just done that instead of spending a whole day wasting time. Don't follow advice on cleaning your throttle body without having a professional scan tool to reset it.
@socalRooster3 жыл бұрын
Can you recommend a good scan tool for me I’m new to this kind of thing so many out there to choose from
@josephdavis383 жыл бұрын
Blue Driver. 🔥
@EricK-es1kx3 жыл бұрын
Get a little Bluetooth one. I use micro mechanic . Never let me down, found it at my local Ross for 4.99
@albertthedogeinstein79833 жыл бұрын
What's the scan tool and how do I use it?
@Gabriel-pj2bk3 жыл бұрын
It's usually very expensive
@franciscojaversaucedososa63333 жыл бұрын
Try Autel MK908PRO
@carmac16522 жыл бұрын
I have a 2016 ram I had an oil change. at the dealership they said I need a throttle body and a fuel injection service .my truck has 68,393 kilometers and it's going to cost me 246. plus taxes ? Should I do it ? Thanks 👍🇨🇦
@larryarellano57402 жыл бұрын
How early do I reset computer on my 2003 Ford escape after changing throttle bod
@antonyglaesman-ww1ny Жыл бұрын
Myn won’t reset , this procedure will not work without a scan tool
@charriez76 Жыл бұрын
Hi I have a 2017 Silverado that needs the reset but i cant find the way to do it without the pc. any advise?
@c.5182 жыл бұрын
I just need to clear a check engine light. If use a scan tool to clear code. Do i have to do a throttle relearn?
@jamesoachs43773 жыл бұрын
Does it work for a 08 town and country? I need to replace the electronic throttle and I didn’t want to take it to a shop. Or maybe a cheap scan tool
@DubbTV4 жыл бұрын
The channel that inspired me to start my KZbin journey 😊 keep up the good work guys!
@1AAuto4 жыл бұрын
Glad to hear it! From one DIY to another, best of luck!
@ROBBG883 жыл бұрын
Iam stuck with my 01 isuzu rodeo v6 right now any help
@tomaslopez43223 жыл бұрын
I cleaned my throttle body and idle feels good except when i rev it in park the idle stays at about 25k rpms. When i shut off the engine and turn it back on it idles good, would i still need an idle relearn?
@Crazycookson11153 жыл бұрын
My truck is doing the same howvdid u fix it .....
@andrewowen5336 Жыл бұрын
How do you relearn for the example video? I have an 04 Silverado
@derekmoore13877 ай бұрын
I got the P2101 and the P2176 yesterday on my 03 accord.
@JarrellMaughn Жыл бұрын
What would be the procedure for 1995 Toyota ae100 ?
@Lee11793 жыл бұрын
2008 Ford Fusion, Throttle body wrench light came on, Cleaned throttle body and put everything back and the wrench is still coming on and off and car is driving rough, like trying to pull out of my driveway and the car will sometimes shut off, No check engine light or codes minus the on and off wrench light,
@1AAuto3 жыл бұрын
+Brandon Hardy We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@fronko90843 жыл бұрын
Why would you relearn the throttle body instead of buying a 6 dollar can of throttle body cleaner then it won't need to be relearned I could see maybe drastic temperature changes made a reason to re learn but if theirs carbon build up just clean the thing out its quit easy and simple and probly the proper way
@TheRoyJames3 жыл бұрын
Some aftermarket throttle bodies help performance better than stock
@amieeduvall34773 жыл бұрын
I’ve bought a 2007 Chrysler Sebring and have problems with it missing and hesitates going uphill took it to a mechanic 😒 they replaced spark plugs 3 times, put new coil packs on and crank sensor and it didn’t fix it. They said they’re was a misfire on cylinder 2. The lighting bolt symbol comes on sometimes. I’m no mechanic but something is wrong if you replace spark plugs 3 times within a year 2 times within 3 weeks apart because they was bad. This video helps knowing what’s going on with my car. Thanks.
@junglejuice233 жыл бұрын
Spark plugs last 60k miles. It should only be replaced if its worn out you should ask them to show you the old ones. Try changing your fuel filter...
@outofmind92222 жыл бұрын
Any idea what the procedure is for a 2012 civic si?
@CarloLeonKolega2 жыл бұрын
SHoud I disconect the battery or something? Also, where is the Tb located on my disel 1.6 mazda?
@ceejayc65022 жыл бұрын
Just disconnect the negative.
@mushmmm1509 Жыл бұрын
Does a 2002 neon need to have this done when replacing tps or iac