Tips for Design of RCC Beam - Civil Engineering Videos

#designofcolumnfooting

[@manishchaudhary8879]

Great job!!! But how to calculate the no.of bars & what dia. of bar has been provided in a Beam..

[@MasterCivilEngineering]

Expertise civil engineering knowledge

[@bariyowhassanmohamed7933]

Thanks. point of correction. In calculation of no. of stirrups, you either convert 5m to cm or change cover to meter.

[@jamshadkhan475]

I am thankful for all your good efforts, Plz can u make a video on the " How to seleect steel dia in colunm, beam or slabs" thanks

[@farhoodkarimimir5883]

Hi, To find depth: 5m/16=0.3125m and this the minimum you can have, you can’t round up the number to lower value of 0.3m or 30cm. You should round up to a higher value like 0.32m or 32cm to avoid disaster:) regards

[@kleinnacion5094]

Agree

[@nathanielanaene3010]

@@kleinnacion5094 true

[@emailtour]

@@kleinnacion5094 building will fall down😂😂😂

[@vonbbm-du30-bsj59]

Absolutely 👍

[@facts9420]

It was useful , 👍👍

[@tasadduqmajeed68]

Waalikum Assalam Sir. A very useful today class. Jazakumullah Khair.

[@ar.avadheshsingh2616]

Two things 1) how 24 will convert in to kg and how to find dia of bars. 2) (5-2×.025)÷0.3 +1 = 17.5

[@MasterCivilEngineering]

Good bro

[@civillogy]

i like it,you explain eveything in detail

[@AbdulQadir-sy1zr]

It's good

[@keoseyha9390]

good explain

[@ramroy9143]

Wow NC defined sir

[@dalliramireddy3395]

Bro ur teaching skills are amezing...🗣👏 But one small requast to u... Please maintain proper units throughout the problems...and one particular dout in this lecture is ...u found out the amount of steel required in terms of area but i want in terms of weight.So please share your valuable reply.Thnkq🤗

[@hanadnor2457]

Bro, in the no of stirrups when u say length - 2xcover, the unit of length is meter which 5m and cover is 25mm as u said so how can we subtract meter and mm (i.e. 5m - 2x25mm) is it possible?

[@rajusekh757]

Absolutely right

[@kondehyoursseh2378]

Am happy with the teaching

[@palashmatubber8496]

Good sar

[@voiceofchemistrynarendersi9873]

Nice info. Thanks and regards. There is an inadvertent mistake in number of stirrups, you should have taken covered length also in m i.e. 2x25/1000, Else it gives wrong answer. N. K. Sharma

[@aaliyahkhan8565]

Very useful

[@dr.fakhar]

how will be decided about spacing of stirups. is it based on guess?

[@carlodigma5128]

Can you show as the complete design for the whole house from roof to footing. Thanks and God bless.

[@amwestengineeringconsultlt9474]

Good

[@homedesign3964]

It's very useful for us

[@9848545003]

Nice

[@SatansBaby1]

GREAT JOB! What would be the load capacity of that beam? 5 tons?

[@imdadullahadil6603]

good luck sir g

[@ernestodelacruz177]

How do we know that it can withstand stress or the load? How do you get top bars and bottom bars? Why area of column? You are discussing beam not column

[@11_kirito14]

Is it thee same process for designing continuous beam and overhanging beam

[@trawallyousman2509]

How did you derived the 30cm spacing.

[@sonukumar-bp4wb]

Assumed

[@varinderladdi1776]

thanks to you up load this video

[@shanmukhl.k.3869]

Thanks 🙏 Pls make video for Plinth beam 🙏

[@xylemfun]

Is that formula can be use for any types of beam such as CANTILEVER BEAM, SIMPLY S. B....to find out depth & breath ....?

[@kanthimathimk7827]

I could follow everything clearly from your video, but what is meant by cover as mentioned in formula for counting stirrups?

[@neelimeghampavankumar8955]

It is clear cover ..and as rod starts placing just inside the concrete right...length in-between bar to edge of beam..

[@mk.maiappan1608]

Thanks you so much

[@khalidali3141]

Sir While finding the number of stirrups , spacing between two stirrups is 25mm so first of all convert it into meters then put the value ... then and then answer will be correct

[@haseenabegum183]

Assalamualaikum bai its very help us.thanks

[@perlitocaballa1551]

what is the size of the steel bar and how many bars on the beam and column thanks

[@hadikallas43]

Sir, how to design the stirrups spacing. I mean u chose 30 cm, but based on what?

[@R.k449]

Great bro

[@naseerhussain3741]

As Salaamo Alaikum sir How to use the 24 cm^2 to die of steel and number of bars

[@surajitpaul9448]

Nice video Sir..

[@rameezhamdule6837]

How should the 24cm2 steel be distributed in the beam. Also can you explain stirrups, especially cover and spacing. Thanks a lot brother

[@saadbhatti9474]

It is concrete cover should be 1,2,3 inches and spacing between strriup will be shown in drawing of beam .that Sir doesn't shows distance between strriups in drawing he suppose etc.

[@saadbhatti9474]

From Pakistan 🇵🇰🙂❤️. Says by ZAIN

[@rameezhamdule6837]

Thank you Saad 👍

[@omanprobashimahossain.2597]

Nice ... abbreviation....

[@vphls]

Thanks! I'll be sure to avoid walking underneath loads supported by concrete beams in India or Pakistan

[@parwezakhtar7810]

😁😁😁 What a satire ,,,, Even we Indian & Pakistani engineers avoid. Blogger is not an Engineer. No need to calculate shear street, bending moment, load etc 😆😆😆

[@habibghazi9974]

Thanks sir, to day good lecture.

[@EARTHSPORT200]

When you were finding steel the answer was 24cm square what is the mean of 24cm square is it steel type or length of steel?

[@monuyadav4126]

It is cross sectional area of all steel bars

[@monuyadav4126]

@Alex 24 cm2 is the total area of steel required in a beam If need to find nos of rebers u need to take any specific dia of reber ( 12, 14,16..any. ) and then calculate area of steel for single reber using formula (3.14/4)*d*d Divide 20cm2 by above value u will get nos of reber

[@michaelnjuguna3625]

Can i use those formula if we use British standard?

[@dorjeewangchuk8996]

How can you directly assume dia of bars and also the spacing between the stirrups and then use those values. Are we not suppose to find what dia bars to use and spacing of stirrups???

[@saadbhatti9474]

Spacing between stirrups should be 6,7,8,9,10 inches it depends upon downward load. The formula to find no of stirrups =(span of beam -2 covers) +1 and divided by distance between one strriup to other strriup which shown in drawing of beam.🇵🇰🙂🙂

[@saadbhatti9474]

Says by ZAIN 🙂 city Sargodha Pakistan 🇵🇰

[@noorulazimkhan8674]

according to my knowledge, it should be. (5-2x0.0025)/spacing+1.

[@emailtour]

Correct

[@ziddee2416]

25mm....25/1000=0.025

[@proshenjitpal824]

Yes, absolutely ur right.

[@barakshahkakar7466]

Great Sir

[@booksourexistence2153]

Thanks a million sirji..... Oalaikumasalam........

[@sladewilson4823]

Isn't the max spacing for stirrups should not exceed the shortest dimension? Which should not be greater than 20cm.

[@perezcarladrian3612]

What is the topic in reinforced concrete design the formula you use? Thank you for answers

[@laughandgrowliam]

How we can decide the spacing of strirrups?

[@RsBala-sx1jx]

sir much important how to calculate how much load it can carry

[@aravindd9963]

Very helpful 🙂 my question is , the beam you designed is a span of 5m,is this beam capable for top load like first floor wall. Or is there any other formula to find those beams with walls on top of them?

[@davorwonder8249]

Good question

[@silentactor558]

Sir i would like to know if Indian Standard is it same as British standards? Thanks fir your ans....

[@balajig4689]

Final tip- beam length in meter and clear cover in mm ...why?

[@paiusbogdan2973]

Sir, according to Eurocode2, for the predimensioning stage, beam hight is 500:10=50 t 5o 500:12=41.66, and this according to the the building ductility class, the number of stirrup's repartition it's done on three spaces in the beam lenght..1 and 3rd spaces, thestirups are distributed 2x beam hight/10cm, 2,nd space:rest of the beam lenght/20cm. It does nat matter the design code, you have lack of information in your calculation

[@johnbenson3174]

And the number of steel require for that size of beam

[@InDepthCreation]

Give specifications about end covers and side covers?

[@sheshnathyadav3061]

No of strip= (5-2*.025)/.3=4.95/.3 +1=20 approx

[@suryamuralim2550]

For calculate no of stirrups, you get dimension for length is meters . but why are you get the cover dimension in millimeters??

[@LocalElectricianPH]

Very brilliant

[@navalmamgain8740]

Thank you sir

[@engrblaisezitisa8787]

Is this from column to column or what? Perhaps the length is 12 m but with many columns

[@M.Hassan19]

This calculation is useful only to get a rough idea. To find exact values of dimensions and steel area you must need to for more complex calculations considering loads and moment. By the way thanks for this rough calculation.

[@iacsse6381]

Bars must be found according to the dia and tensile strength; decrease or increase the number of bars must be inversely proportional to one another. depth can be up to L/36 [in case of concealed beams. am I right?

[@sukumarm896]

Thank you sir. How to find size of steel bars and number of steel bars? How to find spacing of stirrups? Please help us. Once again thank you verymuch. Yours M.Sukumar

[@syedabdulaleem5299]

how converting reinforcement in bars top and bottom stirrup spacing dicesion not explained

[@dharamrahasya4435]

Sir will you please describe the area of steel how we can get steel dia meter and design the bars area exact in beams .

[@YASHDEVCREATION]

Confused with mm meter and cm pls do it correctly

[@yashkhandarkar6345]

For 5 meter span , 20cm×30cm beam is sufficient ????

[@jayabhal7613]

Yes..it's sufficient

[@ernestodelacruz177]

You must check the stress if it is sufficient. This is approximate not accurate. How about the sizes of the reinforcing steel bars? In ductile design the stirrup spacing at length (L) divided by four or L/4 from the column is 10 cm apart. Also the column applies to balance the rigidity. This is a method for foreman. Not for civil engineers. The city engineer will not accept this. He will not issue a building permit.

[@AbdulQadir-sy1zr]

Pls do more beams with examples

[@jilljilladventure9241]

(5m- 2x25mm ) how? Is this mistake or not?

[@abdirashidmohamedmuse717]

Jill Jill Adventure bro 5m is de length of de beam, 2 is mean that the two sides of de cover and their cover is 25mm just assumed nothing else more.

[@jilljilladventure9241]

mohamed farah ousman bro (m - mm) is false bro....( M - M ) is the correct ..see the video ji

[@MonkeyDUchiha56]

We just need to subtract 25 mm by 1000 to make it in m He is just doing in shortcut

[@ISLAMUDDIN-zo9tb]

Jill Jill Adventure

[@SanjaySingh-hf2mt]

i confused.. we are finding column D/B or for beam....?

[@maheshcivil620]

More practical videos in a site plz with each one explanation with merits and demerits. Plz

[@biliban3394]

i cant understand how to find no of stirrups how did you find the 2 × cover Why did you take cover as 25 Can you explain it again

[@saadbhatti9474]

How we calculate steel in long section of beam?

[@MasterCivilEngineering]

Watch here to know

[@khairulariffin8986]

Hye is that got diffrence.for.double storey building or multilevel building such as for.design

[@ziddee2416]

Sir small mistake cover is provide to bheem 25mm... So you have not convert in metre 0.025m

[@selvasiyan]

how we used for steel d 8mm&10mm

[@tasadduqmajeed68]

Kindly learn more about the steel area in colum. in the light of formula (Amount of steel).

[@chomtungemu2473]

For how many storey building Is this rule of finding beam size applicable ?

[@edmondmovilla3260]

You talked about beam cross-sectional area which is 30x20, and not coloum.

[@gelgeloboneya5846]

helpful!

[@namitanagwanshi4965]

Which size of steel bar use in different different beam column and slabs? With thumb rule

[@KulwantSingh-yw6wh]

What is d include slab?

[@mygarden2694]

What is the thikness of beam steel.maybe 16mm/12mm

[@satishkumargarg164]

Is d effective length or gross length?

[@kamranali4971]

Sir 👌👌👌🏿👌🏼👌🏿👌👌🏿👌🏿👌👌🏾👌🏼

[@ratanparmar6155]

First Convert all the dimension in same unit You mixed all the dimensions

[@faridondelsoz345]

انگلیسی کی خو زیاتی ویډیوګانی شته له تا هیله کوو چی په پښتو ژبه ویډیوګانی جوړی کړی زمونږ پښتانه تری استفاده وکړی

[@stelvinthomas9714]

Very helpful

[@omanprobashimahossain.2597]

Dear sir, how can calculate the foundation's column steel rightangle portion's length ? That means 16 mm./ 18mm/20mm steel 's rightangle length how much will come in footing.

[@chethanbhounsley3]

Hi Sir , There were 11pillars in ground floor due to plan change in first floor center pillar was removed in first floor plan so distance between two column became 20 feet so builder added beam which now is 20 feet long i am bothered weather it sustain load

[@renucoorg8912]

NYC sir

[@amirscienceacademy7723]

How to make cantilever beam in old house??

[@JudePiosMusic]

is it possible if i use this method to our country? as you mentioned it is on IS code ,

[@irman3105]

What is rebar sizes....

[@raufliaquat8424]

How we know there 5 steel are come in beam and which dia

[@junaiscm3970]

How to find out steel as per area of cross section