Titan 140 Bar Pressure Washer - Unboxing - Setup & Review - Better Than Karcher?

[@richardjones1373]

Just bought and assembled using your info rather than the manual. One thing I did notice (might have changed since your review) is that there are actually three types of screw. One small but the rest either have point or flat screw ends. You need the pointed type for the base fixing (3:57 in video) as no pre drilled holes in base plastic. Thanks for the great review and info.

[@charlieschannel4192]

👌👌

[@andrewhuntvocalist]

Thanks for the tips for putting it together. Manual wasn’t much use. Cheers!

[@marsy1480]

Every time I see the view of the houses from your driveway, I think I'm back in the Hornchurch/Gidea Park area where I grew up (now in Wales).

[@charlieschannel4192]

The look of essex 😂

[@marsy1480]

@@charlieschannel4192 I'm taking it that you aren't a million miles away then 🤣. On another note, I am after a really easy to use pressure washer. Im a girly with pathetically weak joints so need something with easy to pull trigger and fitment of accessories. I've only got a tiny garden but the concrete gets filthy! Any ideas would be most welcome! Tia

[@charlieschannel4192]

This is a good product but it's bulky, The bosch aquatak 110 is small, affordable, light and does a pretty good job, so probably that 👌

[@marsy1480]

@@charlieschannel4192 brilliant, thank you. I will go for the Bosch. I was thinking that it looked really lightweight (I'm as weak as a kitten 🤣).

[@loughboroughjim]

Thanks, very helpful video - it convinced me to buy one! My only issue with the assembly is that when I'm supposed to put the final four screws in the base plate, only two actually go in... The last two screws don't have anything to grip on to when I attempt to tighten them, and they just fall out - exactly four minutes in to your demonstration. Have I done something wrong? (The unit does work).

[@charlieschannel4192]

They should go in there, are the screws different sizes or lengths? and is the base plate deffenatly in the correct place??

[@loughboroughjim]

@@charlieschannel4192 Hi Charlie, I put four identically-sized screws from the original packet into the base plate attachment, which looks to be in exactly the same place as yours in the video. Screws 1 and 2 were very fiddly to fit in, and they firmly secure the whole attachment to the base plate. When I then insert screws 3 and 4 into the screw holes on the attachment and turn the screwdriver, there doesn't appear to be anything corresponding on the base plate itself for the screws to fit into or to grip onto, so they just fall out again. As I said earlier, everything else in the setup went exactly as per your video, and the pressure washer works fine - it just seems strange that these screws don't have receptacle holes on the base plate to screw into - and the base plate feels slightly less secure than it should be...

[@charlieschannel4192]

@@loughboroughjim yeah very strange, tbf as long as the base is secure and working then it'll have to do, maybe try a longer or wider screw??

[@jaywalker1233]

@@loughboroughjim watch the video again carefully, and you’ll see that the reason you could not secure those 2 screws is because you did them in the wrong order - you put the base screws in first and they *must* go in *last* . You must follow the exact order shown because you need to be able to flex the plastic accessory in order to line up the “troublesome” screws through the “loops” on either side of the accessory and into the *deeply recessed* matching holes on either side of the jet wash bottom housing. This is the *trickiest* part of the whole assembly and you also need very good light to see what you’re doing. A magnetic Phillips head screwdriver will make this much easier (or a small gob of blu tack). If you kept the two “spare screws” then I suggest removing the base accessory and trying again as explained above - I’ll be v surprised if you don’t succeed (Note you might need to remove the wheels first - take when doing this not to snap the wheel retaining lugs). Btw, the “small” screw isn’t needed - the top lance holder snaps firmly into place without it and the screw distorts the plastic when screwed home (not good long term)

[@SonofChurchill]

Thanks for info on adapter, My AD snow foam gun no longer fits my new Titan. Had a poor Nilfisk before.

[@arpadvarga3475]

I got the macalister version.i think it's almost identical. It's much more sturdy than my previous karcher

[@itsallabouttheclag]

I have this and it’s a fabulous piece of kit for the money. Can you get a longer hose to fit this model the 6m hose is a tad to small

[@roylang9754]

Yeah Screwfix do a titan 10m hose for £20 👌🏻

[@AzadBrepotra]

Great vid. If given a choice between the Titan Pressure Washer 100 bar vs 140 bar - which would you get & why?

[@charlieschannel4192]

The 140 bar one, £100 40 bar more pressure, some more gizmos, come with a warranty, and surprisingly quiet 👌👌

[@some_one_2_3]

Brilliant video Charlie. I feel really informed now and I'll be buying this pressure washer. Liked and subscribed 🎉

[@charlieschannel4192]

Glad you enjoyed it 👌👌 thankyou

[@hennaartistry3290]

Struggling to fit the patio head, thanks for your video as the instruction was poor

[@1786crafty]

Great video chap. Would like to see how the big boy 155 bar does. Seriously reckon this is better then your karcher. Keep up the great work.

[@jamesmacleod1076]

Hi Charlie, thanks for your video certainly made assembly straight forward for me. I would like to use snow foam for car cleaning in the future but not wanting to spend almost the same money on a foam cannon as the pressure washer cost ~ the MJJC sv3 is £70 😂. Can you suggest one on the £20 to £30 range & if it needs an adapter what sort? Thanks in anticipation 👍🏻 Jim

[@charlieschannel4192]

No problem, the halfords is proably the best lance for its price around £35 atm, in the box it comes with, the lance, a short tip adapter, a karcher connect and a halfords pressure washer connect. (im not sure if you will need to get an adapter for your lance i will give you the link) it has the 1/4 connecter with it which is good if you want to try some other products - www.halfords.com/motoring/car-cleaning/snow-foam/halfords-advanced-premium-snow-foam-bottle-kit-712494.html amzn.to/4cuLF7a if you do try this one get the lance from halfords 1st and see if the connecters will fit your titan, if it does not then the other link should be the correct adapter, i know this is abbit more than what you said, but anything at a lower price point just isnt up too it, hopefully this helps, let me know how it goes regardless.

[@jamesmacleod1076]

@@charlieschannel4192 thanks so much 👍🏻👍🏻

[@aceedal]

Thanks for the video the instruction manual was not very good wasted a lot of time with it i had three types of screws but found the correct holes Thanks again

[@charlieschannel4192]

👌👌 no worries

[@polopol123450]

Great review vids man 👌🏻, do you reckon the next model up, the TTB2200PRW is much better?

[@charlieschannel4192]

Im notn sure ive never used it , works out around £40 more for 10 bar more pressure, so it's a little more pricey, but depends if you want abbit more oomph 👌

[@SonofChurchill]

@@charlieschannel4192 I looked at next one up it's got a wheel to roll up holes and as above just 10 bar more would you real see that. As this is a month ago what did you get ?

[@sabotage3d]

Great review! Only review to show db noise level which is essential. Do you think it is quieter than Karcher K3 and K4 for example?

[@charlieschannel4192]

Yes this is quiter than the karcher k3 and k4 👌

[@sabotage3d]

@@charlieschannel4192 Thanks mate! Will buy this one I had to return Parkside PHD 170 as it was 97db!

[@sabotage3d]

@@charlieschannel4192 Is that what you recommend for car cleaning and occasional patio cleaning?

[@charlieschannel4192]

@sabotage3d I have been since I bought it, I bought it this year, buts it's been pretty good so far 👌

[@sabotage3d]

@@charlieschannel4192Nice! I only have this version Michelin MPX19ELP available in my country, but I think it is exact same as Titan they both are made by Annovi Reverberi.

[@Steve_882]

Great video.. was going to get the titan 150 but will stick with this 50 quid cheaper ...Thanks

[@wrzlygummidge]

great vid Charlie, much easier to follow than the hieroglyphics in the instruction manual! Nice one, atb

[@charlieschannel4192]

👌👊

[@dannychapp]

Thanks for the comparison. Shame on the wobble think after a while a new gun upgrade would be key. How was the trigger? I know some make your hand hurt after time using.

[@charlieschannel4192]

The trigger is actually pretty light, I think it's a great bit of kit tbh 😂

[@swimgood3873]

Can you link up the quick tip connector and the foam cannon as well please ? Great set up.

[@charlieschannel4192]

amzn.to/3yZvMHu that's the titan adapter That's the lance mjjc.com/collections/foam-cannon-s-v3 Trigger gun mjjc.com/collections/high-pressure-washer-guns-and-nozzles/products/5-in-1-spray-nozzle-and-trigger-gun-kit-suitable-for-all-karcher-k-series-pressure-washers

[@charlieschannel4192]

The short trigger is for a karcher gun, so i need to get a adapter for it 😂

[@swimgood3873]

Im with ya 👍​@@charlieschannel4192

[@catherinemoss785]

Great video - really helpful. Thanks very much Charlie!

[@MJM_TV1]

can you give a link for that mjjc snowfoam?

[@charlieschannel4192]

mjjc.com/products/mjjc-foam-600ml?variant=46660415586599

[@uwaissabir3597]

On the Amazon adapter there’s two types with aqt and without which one is it for this titan

[@charlieschannel4192]

Pressure Washer Adapter for Bosch AQT, 1/4'' Quick Connect Fitting Car Wash Water Gun Head Adapter Washer Spray Wand Couple Snow Foam Lance Adapter Foam Cannon Gun Connection Fittings amzn.eu/d/eibfurw

[@jawadamjad7864]

Is there a way to connect those swivel pressure guns to the pressure hose directly instead of having to use the titan gun and another attachment?

[@charlieschannel4192]

Swivel pressure guns??

[@jawadamjad7864]

@charlieschannel4192 yes like the MTM SGS35 - could please show how that would fit and what attachments would be required? Thanks

[@WuIIie]

Hi mate. Thanks for the video. I ordered the adapter that you linked in the description, I’ll probably order the MJJC foam cannon as well. Is there any specific adapter I should order with the cannon? Or can I just order it without an adapter? Does the adapter I’ve ordered in the link fit onto the cannon? Also could you tell me where you got the shorter quick tip connect that replaces the lance? Thanks

[@charlieschannel4192]

You can order any connection type when you order your lance, so if you have a karcher washer you can have a karcher connector, if you have a bosch washer then you'd get a bosch adapter, and so on. But the downside of that is if you want to change your washer you'll need a new adapter head for your lance, so ordering the quick connect allows you to use it with other washers, but you'll still need an adapter quick connect to what ever washer you have, the short tips are avaliable in lots of places, mine is from the mjjc trigger gun set, but amazon and halfords and some good options, might have to be some trial and error hope that helps, (just check what quick connect you want/need as there is 1/4 connections and 1/2 connections)

[@WuIIie]

@@charlieschannel4192 I have the exact same pressure washer as the one featured in your video. So I’d be better ordering one with the Bosch connection? And between that and the adapter that’s linked in the video I should be good to go? Thanks

[@charlieschannel4192]

Yeah then you should be fine 👌👌

[@stevensleightholm5648]

I bought this today, your review was a great help, thanks

[@charlieschannel4192]

👌👌

[@Sarahalimiyan]

Hi, I have Titan Pressure Washer TTB1800PRW with a rated pressure of 9.5 Mpa and Rated Flow Rate of 5.5L/Min Please confirm if you have used the same product? Just want to make sure that the foam cannon and the attachment would work as it is costly One more thing, do I need to keep the water connection on while using the snow cannon? Thanks in advance your video is really helpful

[@charlieschannel4192]

Yes, this is the same product. Yes, these attachments should all work, and yes, you must keep the water attached at all times when using this washer 👌

[@Sarahalimiyan]

@@charlieschannel4192thank you so much! Could you please also share a link for the quick tip connect you used?

[@charlieschannel4192]

The adapter is this amzn.to/3xTcIdV

[@charlieschannel4192]

The short tip connectors you can get in a few places, amazon halfords, just user prefrence 👌

[@Sarahalimiyan]

Thank youu

[@RkH1st]

Is there a decent foam cannon that just fits without getting other connections?

[@charlieschannel4192]

You can get any cannon that you want, just when you choose it, make sure it comes with a titan / bosch aqauatk connector, most lances allow you to pick what adapter you want to be on it, like this one mjjc.com/collections/foam-cannon-s-v3/products/mjjc-foam-cannon-s-v3-0-for-bosch-aqt-aquatak-and-blackdecker-pressure-washers If your not sure what lance is right and you want to try a few, then I would recommend a 1/4 quick connect, which all lances come with. This way you can swap around whenever you like 👍

[@RkH1st]

@@charlieschannel4192 Why do my replies keep getting removed?

[@uros9151]

How would you compare it to the Bosch Aquatak 120 (have it avaible for under 100£ atm), is it best budget option for that money?😂

[@charlieschannel4192]

I havnt tried that washer, but the titan for £100 is pretty epic 😂

[@roserobinson5781]

Great video ..thank you Charlie 🇮🇪

[@charlieschannel4192]

Glad you enjoyed it

[@edmitchinson1014]

How did you get the electric cable fastened using that fitting that came with the washer please.

[@charlieschannel4192]

What part do you mean??

[@edmitchinson1014]

Hi Charlie. I got a piece of black plastic about 6 inches x 1 inch. It has a rounded edge that fits into the body of the washer. It's used to tidy up the electric cable when not in use. I can't work out how it fastens. Thanks.

[@charlieschannel4192]

You have to attach it before you screw in the top cover, so it goes inside of it, if that makes sence 😂

[@domheathcock4351]

Screwfix Just brought out a titan car foamer to fit on all there washers.... Could you try it out? It's £25

[@charlieschannel4192]

You've just given me a video idea 👌😂

[@roylang9754]

​@@charlieschannel4192bought a titan foamer and not too bad for a pony. Used Halfords advance snow foam with it and took around 4 mins to drip off my taxi 👍🏻 Looking forward to your review and tips 👌🏻

[@twills]

Does anyone have a link for the Snow Foam attachment he used? :)

[@charlieschannel4192]

mjjc.com/collections/foam-cannon-s-v3

[@auntiemandy5638]

Got this today for £79.99 👍

[@charlieschannel4192]

Bargain! 👌

[@alanwilkinson9487]

Absolutel bargain.. 140 now..

[@siutim-jc9zo]

Autoglym foam lance need to use adapter?

[@charlieschannel4192]

When you buy the autoglym lance, you would need to choose the correct adapter, but you can use the quick connect for this as well, as long as the autoglym lance has a quick connector aswel

[@Phookinell]

Snap On screwdriver probably cost more than the pressure washer…😆

[@charlieschannel4192]

😂👏😂

[@jonathan755]

Great video 👍👍👍👍

[@tonymcfeisty2478]

this model is on offer at the moment £20 off, bargain

[@swimgood3873]

Is it?

[@tonymcfeisty2478]

@@swimgood3873 It was at the time I posted, 2 weeks ago

[@hexboxx735]

Thanks mate, this is really good. The instructions for it are terrible

[@charlieschannel4192]

👌👌👌

[@truth3358]

Same as you paid 69

[@szybared]

Dzięki Charlie za naprawde dobry film poglądowy, właśnie kupiłem myjkę Titan i zaraz będę sprawdzał jak działa.👍✌️🙂.

[@charlieschannel4192]

Good luck mate 😂

[@szybared]

@@charlieschannel4192 what you mean mate (?) 🤔

[@charlieschannel4192]

As in hopefully it all works and you enjoyed it 👌

[@szybared]

@@charlieschannel4192 👍✌️🙂