Top Skills of The Mechanic To Full Restoration The Hitachi 3-Phase A-1500 3 In 1 Woodworking

[@gerryboard6615]

Learn how to remove and fit bearings. Learn how to make correct and safe electrical connections. Wear hand and eye protection when welding. Use breathing and skin protection when spraying. Do not use excessive grease on a machine which is going to create lots of dust. When you find a bodged chain tensioner, make a new one. You are not a mechanic, you are a painter and decorator.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you lots of health

[@chrisdavis5718]

Good suggestions. Now why don't you restore something and show the right techniques instead of just sitting on the sidelines and criticizing.

[@mathewmolk2089]

There is nothing more stupid then a pedantic safety Nazi ,,,,,especially when the finished product is virtually 100%..... I do love running OSHA inspectors off job sites, BTW. - Never lost a case yet, either.

[@normanbott]

And also, the working surfaces of woodworking machines are never painted, left plain cast iron and waxed. See how much rust was on the unrestored surfaces for a clue.

[@ОлександрМихайловичМалайчук]

Перш ніж працювати з таким станком, потрібно мати елементарні навички та знання про обробку деревини, бо можна залишитись без кінечностей. Будьте обережні!

[@leatherandsilver350]

Когда маляры взяли в руки молоток, разобрали и раскрасили станок, после чего он перестал работать..........

[@hugben235]

Very good 🎉🎉🎉

[@ИгорьПетров-з4э]

Был шанс поставить новый натяжной ролик, но не поставили, -пусть цепь грызет детали. Часть работ выполнена без необходимых регулировок. Поверхности столов должны быть отшлифованы, а не покрашены. Натяжение приводных ремней выполнено неправильно. Ножи на краске! Халтура. Ужос нах! Сам станок хорошая добротная вещь.

[@Лежанадиване-в7л]

для ютуба потянет

[@77777bober]

основная задача все покрасить)))

[@joseeduardohortacelso2214]

UM EXCEPCIONAL TRABALHO PARA FAZER COM QUE ESSE LINDO EQUIPAMENTO FEITO COM 3 FUNÇÕES (SERRA CIRCULAR, DESENGROSSADEIRA E PLAINA) VOLTASSE À VIDA. ESSA MARAVILHOSA MÁQUINA FOI FEITA NUMA ÉPOCA EM QUE ERAM PROJETADAS PARA DURAR.

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@MarcoMarcelloCaponera]

Restoraton..skills.secondo.me.sei.un.gran. Genio..che Sa.fare.le.sue.riparazioni.fino.al.punto.di.portarle.ah..nuovo.ciao.da.parte.del.vostro.fans.caponera.marco.marcello.di.castihlione.chiavarese.in.provincia.di.genova.che.e.della.regione.liguria.adesso.vi.saluto.ciao.❤❤❤❤❤

[@NadolbenBlogspot]

чушки пачкающие краской рабочие поверхности и направляющие кареток это уже привычно, но покрасить пильный диск и прижимные планки ножей - однозначно новое слово в зарабатывании премии Дарвина...

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@7551286]

Excelente trabajo de restauración, recomiendo calibrar la plancha de salida a la altura de las cuchillas para que no muerda la pieza de madera a la salida, saludos desde Bogotá Colombia

[@restorationsskills4967]

Thank you very much.

[@paulfellows2094]

another one back to life fantastic job mate very enjoyable video you are very talented love the channel

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@larrykelly2838]

Nice restoration

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@DJ-qh3wm]

Vaya restauración warra.....

[@restorationsskills4967]

Thanks

[@sportingeventsbycoachbozel4233]

Amazing job. Outstanding.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@MarcoAntônioDossantos-p6z]

Meus parabéns brother

[@restorationsskills4967]

Thanks a lot. We hope all the videos we make are well received by you. If possible, follow the video and fix your own device. Please follow and support us!

[@derekadams729]

Good job kuya.

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@jhkoerner1080]

Dangerous on so many levels, this is a great video of what not to do. Amazed he still has fingers intact

[@Tonydeep1222]

Very very good 🎉

[@lauraclay4164]

That was a lot of work. It runs and does what it was intended to do. Great job!!!

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@fredrikberntsson1259]

Love the green paint!!

[@restorationsskills4967]

Thank you very much.

[@michaellawrence6677]

You sure made it pretty. It’s not quite what we’d call a restoration but, it made a very nice video. I can’t believe you painted the work surfaces. If someone did that at our shop they’d be fired. But all in all a pleasant video.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@Starboyxoxo1]

Good work that he does

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@jorgehenriqueribeirodasilv396]

Show...👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@77777bober]

особенный штрих это деревянная колодка под кнопкой !)))

[@Jerzy-xm1tb]

Z tym napinaczem łańcucha to nieźle przesadziłeś. Rozwiązanie z końca XVIII wieku

[@restorationsskills4967]

Thank you very much.

[@ROADKILL4147]

wow that was alot of work to restore that nice job 😎

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@ROADKILL4147]

@@restorationsskills4967 your wc and of corse, keep up the good work :)

[@frankdearr2772]

Great topic , thanks 👍

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@traktor-fan4586]

God Job ei leick et !❤❤❤😊😊😊

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@BoffoVerse]

Gut gehunzt

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@jesussorianominano4024]

Madre mía qué máquina más bonita . me encanta

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@РамильШарипов-и8ч]

Рейсмус конечно вещь

[@Dan.d649]

Excellent work!! When you have all the tools and knowledge to get this beauty back to life, and know how to use them, it's a pure reality to see it operating well again and looks exactly brand new. Thanks for sharing!! I appreciate your fantastic work!!

[@Sonomaniaque]

I hope this is ironic ???

[@x84pav84x]

30:25 спасибо большое за то, что выполнили мою рекомендацию, насчёт экрана. И сами берегите глаза, сварка очень опасная штука.

[@restorationsskills4967]

Thank you very much. You are definitely a good worker too. Thank you for all your contributions. We will try to improve products as well as work safety

[@nuriurfanl4583]

wandefoooool nıce art

[@donamir3652]

👌👏👏👍

[@x84pav84x]

24:44 для этих целей есть специальное приспособление, на которое натягивается наждачная бумага. Хотя можно использовать и простой деревянный брусок.

[@user-z9j9j]

Супер

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@x84pav84x]

21:11 вот так делать очень опрометчиво, можно запросто сжечь обмотку двигателя.

[@sergeiivanov5325]

Отличная работа!!!👍 Respect!!!

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@donamir3652]

Un trabajo super!! ✌️👍

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@ejtakach]

Gives a whole new meaning to"self-basting bird".

[@restorationsskills4967]

Thank you very much. you are so funny

[@wrongfullyaccused7139]

So, when was the top skilled mechanic going to show up?

[@garyjones2582]

Keep it lubricated and out of the weather and it's ready for another 50 years...

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@bushman4124]

When i saw you use the jointer, well not that much at once and make a pushblock for it, but more important align the front table with the spining blade so you don't get so much snipe because at the last end you push it down due to the hight difference. and look for a diiferent saw blad that match your speed. little rough but nice restauration. love the green. to get less snipe through the planer just make an extension table you can slide in sou your outfeed table is longer, and that takes a lot of snipe away. whatch your fingers and enjoy the machine.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@bevomcbevenstein]

This isn't a restore...it's a paint job. LOL at how the jointer ripped that big chunk of wood out of his test block.

[@enrico-q9v]

👍👍👍👍👍👍👍👍👍

[@beanieweenie9543]

Man went wild with the paint! Painted everything including the chicken. 😂😂😂

[@MrTarkus007]

🤣🤣

[@adilsonvarella3088]

Ficou chique parabéns 👏

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@MrCheezeus]

you might want to restore that flathead screwdriver while you're at it lol , it's seen better days

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@william6526]

It's to bad you don't have a sand blaster to remove all the old paint and rust In places you can't get hand tools into to clean.Never paint the work surfaces of any wood working machine. Just use a wire wheel to remove the rust and put a light coat of oil on the surface and wipe off any oil. The oil is only to keep the surface from rusting again.

[@restorationsskills4967]

Thank you for your feedback so we can better improve future products. We are also planning to buy more sand blasting machines to serve our work. We wish you and your loved ones good health!

[@mathewmolk2089]

I got one of those pressure washer sand blast attachments. - If you got a pressure washer you might try one. - Ours works pretty well and they do not cost much. Just is does use a ton of sand. @@restorationsskills4967

[@antonymars4234]

Чувак кордщеткой в шортах шпарит... Монстр

[@zadabjlil2281]

This motor 380 or 220👍🤝

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@restorationsskills4967]

That's right. Maybe you're also a good mechanic

[@mathewmolk2089]

Very, Very good job. Just is there a reason that you painted the bed surfaces? - Those normally would be left bare. Also I think I would have been tempted to take a link out of that chain. Really good job, though. YOu got to have a WAY better memory then mine. I'd have never gotten it back together BTW Speaking of painting. You are one of the only persons on KZbin I have seen that actually knows how to spray paint. Once more. Good job. - That planer works better then our like new Rockwell.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@МаркаСталииИванычъ]

для получения травмы самое то............

[@vaskapro]

Хочеш починить станок? Зови этих специалистов, останешся без станка.

[@tukangumpruk4546]

Nice job,the machin is new again 👍👍

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@maxpolaris99]

I never saw a bent over bolt as a chain tensioner before 😁. I guess if the bolt is known to be much softer than the chain.

[@william6526]

One thing I've noticed the first thing he does is to spray all the rusted nuts an bolts with a pentrating spray and let's it sit for awhile to let the spray work to loosen the rust. Other restoration channals I've watched just use a bigger hammer or a cutting torch to remove the stuck nuts an bolts.

[@restorationsskills4967]

We use that spray to make it easier to open the screws. We very rarely cut. thank you

[@thisolesignguy2733]

Great job!!! The only things I think you'll regret later is not taking a link out of the chain and painting the planer surface since it will get sticky over time. But no complaints here, I especially like the green!

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@mariolucich3927]

Super work but that got me so frustrated, it was begging for a small gear to be put in place of that bent bolt

[@miltonsousaribeiro3358]

Oieee amigo ficou nova top demais parabens abraço

[@restorationsskills4967]

Thank you very much. Please follow and support us!

[@BlackDog-g3g]

I've NEVER seen anyone paint threads, gears, and rollers ! I'm glad that's not MY machine. You guys want to try again???

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@ZygmuntKiliszewski]

Hello, quite precise renovation of this multifunctional woodworking device (planer, thicknesser and saw). I noticed a simplified chain tension in the form of a bent screw. I think you should get an appropriate brass slide, and preferably a roller with a spring tensioner. You put a lot of work into this renovation. Congratulations and best regards 😀.

[@ZygmuntKiliszewski]

Thank you for the likes 😀.

[@restorationsskills4967]

Thank you for your feedback so we can better improve future products. Wishing you and your loved ones good health!

[@ZygmuntKiliszewski]

@@restorationsskills4967 Thank you for the likes 😀.

[@richardwhite4277]

I think the drive chain needs a link or two removed to take out the slack

[@restorationsskills4967]

We rebalanced the chain and it worked normally

[@mathewmolk2089]

Good !!!! @@restorationsskills4967

[@themusicman-ij7op]

I noticed you put grease on the slide bars, grease and sawdust don’t mix well 😂 When using the buzzer or thicknesses no more than 2 mm takeoff .

[@mathewmolk2089]

Wrong for 2-reasons. 1- If it was a problem then why did Hitachi build it with grease fittings. = 2-Yje sawdust around the slides actually acts like a seal, and keeps the grease in, ,,,,, BTW, Check Kieth Ruker's restoration of the big planer mill at the museum. They take off a good 1/4" (7mm) at a time. - If the machine will handle it,,,, let it handle it.

[@zolatanaffa87]

Work done a lot, even too quickly! you did not check the bearings if they were worn, where you welded you left the weld very poorly finished and during painting you also repainted all the milled parts which served as a reference for a correct coupling of the parts, in addition to having also painted all the screws with lock nut which served as an adjuster furthermore, you used so much grease that after the first two hours of work it is already full of sawdust and shavings that block all the mechanisms. You have created a beautiful display object not a functional machine

[@mathewmolk2089]

Then how is it it is working perfectly? - His way is better then your way.....("Reference surface"with .004" paint on a woodworking machine.....Are you on Drugs?)

[@luciooliveira111]

Parabéns meu amigo, proficionalismo total!

[@restorationsskills4967]

Thank you very much . Please always follow and support us!

[@fighter3120]

,👌

[@ВОИНВОИН-в9и]

Он вообще имеет придставление деревообрабатывающих станках . Ну пока не лишится пару пальцев не научится

[@restorationsskills4967]

Thank you

[@slonvposudnoilavke]

Интересно зачем красить рабочие поверхности столов

[@Joss-p3p]

You don't have to be rude with the equipment to be a mechanic.

[@joelchabot5167]

NNice restoration, with painted chicken to eat

[@restorationsskills4967]

Thank you very much. you're really funny

[@redentosanna279]

Potevi dare pure una verniciata all' interruttore visto che c'eri

[@restorationsskills4967]

Thank you

[@x84pav84x]

1:16:05 я лично сам видел, как человек за секунду остался без пальцев. Сначала он не понял, от шока, что случилось. Я лично сам оказал ему первую помощь. Я лично сам собирал его пальцы в пакет со льдом и отправлял в больницу. К счастью, их смогли пришить обратно. Не очень хотелось бы, чтобы это случилось с вами. Техника безопасности написана кровью, очень печально, если вместо меня вам это докажет беда, которая может случиться.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@levyemmanuel4549]

bon boulot , mais on ne peint pas les tables de travail sur lesquelles va frotter le bois

[@MarkDunham-g3b]

I need some one with this skill set. I am Mark Dunham. It would be easy to get you a work visa to start. I have a place for you to live, and a business for you to work under.

[@restorationsskills4967]

Thank you very much. It would be great to work with you

[@MarkDunham-g3b]

Right now all I have is a room, 3 hots and a cot to give you for your work. I am looking for someone with your skills and a few others. Like a tailor, seamstress, shoe maker, butcher, a cook and a person who can clean the house, as well as someone to take care of my land-mowing, planting and removing trees, etc…I have a project right now that would to be great for you to help out with. I am build a new nation as a citizen of the free world and I am looking for indentured servants. I look forward to workers dedicated to working for me for their whole life. But it will become a good comfortable life for you. Let me know if you have interest. I would want you to work for 2 years under the visa, then we can see about getting your family over here. I must be willing to dedicate your life to myself service.

[@x84pav84x]

1:29 к сожалению, меня снова не поняли. Очень жаль.

[@restorationsskills4967]

We really don't understand what you mean. Can you say more about this

[@x84pav84x]

​@@restorationsskills4967конечно могу. Вы используете инструмент без защитного приспособления. Это очень опасно, если вдруг разорвёт диск, его осколки могут причинить тяжёлую травму.

[@x84pav84x]

​@@restorationsskills496710:23 и здесь то же самое.

[@divi54321]

As soon as he painted the machined surfaces and lead screws he ruined it!!!

[@x84pav84x]

Советую хорошо отрегулировать ножи, чтобы ровно стругать.

[@slonvposudnoilavke]

Зачем. В данном случае чем больше шпатлевки и краски тем лучше. Ножи, это не современно. Не они трогают, а краска на них.

[@icebear8773]

buena restauración pero esa máquina está toda mal calibrada, necesita un montón de ajustes antes de que sea útil

[@restorationsskills4967]

Thank you very much dear friend.

The worst part of this "restoration" is where take a iron casted part to cover wit clay and polish.... Stopped video, took a walk. That is not a restoration.

[@bob1947essex]

That wasn't a FULL restoration. Surfaces that shouldn't have been painted were, the cutting blades are blunt.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@lizdini722]

It is better than it was at the start. Somebody could make use of it!

[@nahimibrahim107]

You could have done much better and you need to learn how remove and install bearings properly.

[@restorationsskills4967]

Thank you very much

[@Книжностаночныйклуб46]

Сэр , а где вы нашли недостающие детали станка ?

[@restorationsskills4967]

We had to go to groups of places that sell used items to find the missing items

[@bernardcartwright9272]

Sliding surfaces should NEVER be painted including the saw blade. Should have bought new planer blades. Altogether a dreadful restoration.

[@legion499]

How many different channels do these guys have? I don't guess it's a problem but why not just compress your shop down to just 1 channel?

[@obetitiwows1752]

Since you have fixed that machine it is not possible to work exactly. The repair is too fast without adjusting the machine properly, it shows in the precision of the blades, too much paint in places where they shouldn't. It's not all about painting the machine and making it look like new, but rather proper operation. I think you know how to do it better Regards(Bearbeitet)Original wiederherstellen

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@ЮрийБольшаков-ю4ю]

Хот бы толстые слои грязи убрал, водой помыл, обдул, высушил, а потом бы и красил. Удивляюсь как он перед реставрацией в грязи специально не измазал как всегда. Вот где халявщина.

[@АртемС-ц2б]

Тут видимо все ради контента. В итоге от фуганка одно название.

[@Italianwop]

I would not paint all the machine.

[@restorationsskills4967]

Thank you

[@Sonomaniaque]

Je serai surpris si le gros pâté de soudure tient longtemps...Bon, on sait que ce sont des vidéos pour générer de la KZbin money, et rien d'autre. et ca marche, puisque on les regarde. Mais ca fait de la peine quand on voit quel est le serieux de leur travail. Je me demande même si ce n'est pas eux qui sortent des machines sous la pluie pour les faire rouiller et ensuite les "restaurer"...lol

[@restorationsskills4967]

You have really funny thoughts!

[@matmat5898]

It looks like low RPM for this type of machines.

[@restorationsskills4967]

Thank you very much.

[@stevenmattson3164]

Painting the table top? Why not just wax it? I know, you have a humid environment. That paint is going to wear off quick and might get on the wood being cut over time. I also have a lot compassion for your chicken sharing the spray booth...

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@Mike-nn7jy]

a lot of work respect, but I didn't see that new ball bearings were installed, the machine shaft or cutting head looks like a flap knife shaft, these have not been allowed to be used in Germany for around 50 years, nobody sprays the threads with paint, the circular saw did not have a riving knife or a protective cover

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@mathewmolk2089]

Our Rockwell planer has the identical set up on it and it is less then 10 years old. Then the first think anybody with a part of a brain is remove the guard from a table saw before they get hurt, -It is only there to keep you from dropping a board on top of the blade and have it shot backward - Bet you didn' know that. The riving knife has it's place, especially when ripping but has to be removed for most other table saw operations. ,,,, Damn collage boy Safety Nazis.who never actually ran a machine.

[@АннаОрлова-щ2р]

Привет всем. Сразу чувствуется специалист красит обязательно все винты и шестерни. И зоны прилегания обязательно ушм надо пройти. Столь верхний тоже покрасить не забыл а то как же дерево будет после фуганка без зеленых пятен не правильно. Как идет разбор двигателя и снятие шкива это полный пиздец. Первое зачем снимать шкив полько для замена подшипников. Разберем как двигателю пизда пришла полная. Это когда резаком грелль вал и спалил обмотки хорошо это видно на 22;43 времени. Шкив один из ручейков откололся в двух местах шкиву скорей под выброс 21:41 сколы очень крупные. Стучать по валу тоже не надо без проставок бронзовых наклеп образуется. А лучше всего довить прессом через центровку. А когда по крышке двигателя стучать молотком начал это просто ужасно. Что ему мешало полошить деревянный брусок и по нему стучать. На этой крышке идет поясок чтоб центровать крышку на двигателе. И упереть в деревянный брусок. Чтоб заход со стороны шкива не заминать. Чугун он тоже варить не умеет. Чугун надо греть перед сваркой 400-600 цельсия градусов. И после сварки еще раз греть до 600. И потом в печи при 250 градусах 2-3 чеса держать. А потом он дорвался до краски и начал красить все зоны прилегания. Что удивило меня это поворотный стол и что он заклеил направляющие станка. А вот зоны прилегания не стал. Столь рабочий покрасил зачем то. Внутри двигатель покрасил зачем то. Покрасил все винты шестерни это просто пиздец какой то. А барабаны с ножами и ролики на хуя он покрасил дебил. Особая песня это установка подшипника на барабан с помощью болта. Там нужна проставка по диаметру чтоб она равномерно давало давление на подшипник 46:13 Да масленки от тоже перепутал в первую надо было жидкую смазку лить. А во вторую литол когда вал и барабан ставил. И кстати видно по чему красить зоны прилегания не надо все валы и барабан с помощью молотка ставит. И еще не надо стучать по валу. А когда натяжитель цепи делал 51:34 он что не мог взять любой ролик для машины или звездочку от велосипеда. Нет поставим болт вот и нету натяжение цепи. Шкив на барабан походу сначала пытался забить молотком просто стучал по нему видны следы сколов возле вала. Взялся за деревяшку через нее стал стучать. И вот тут сразу видно по чему по валам нельзя стучать на концах образуется наклеп его надо напильником снимать и красить не надо. Но верх ахуенности это приклеенные куски шкива 1:05:52 это просто шедевр рукожопости. А пильный диск зачем красить. При установке ножей в барабан выставить их на глаз это полная жопа. И да а что он не шлифанул ножи. И кстати где обкатка станка индикатором и прогон деревяшки примерно 650мм по стороне и замер перепадов с углов. А так станок очень простой в восстановление там допуски на размеры многие 0.1 мм. И да автор тебе книги СССР по слесарному делу djvu.online/file/RWmcefTveXdXD А так исключишь ошибки и следующий станок сможешь сделать уже нормально

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health

[@ВладРе-к6к]

Ты как маленький. Это реставрация для ютуба, а не для работы. Найдет лоха - хорошо, а нет - в металопремку скинет, основной заработок с трубки...

[@АннаОрлова-щ2р]

@@ВладРе-к6к привет но есть много людей кто посмотреть это видео и решит что так надо восстанавливать станки. А так может прочтут коммент и сделают более правильно. И книжку по слесарке почитают все умнее будут.

[@ВладРе-к6к]

@@АннаОрлова-щ2р это врядли. Есть люди с руками, а есть зеваки и эти множества редко пересекаются)) Почитай коменты, они в основном от зевак и для них всё сделано великолепно))) Даже немцы, дотошный народ, и то пишут - молодец, всё круто... Вырождение технарей и восхождение пздаболов...

[@x84pav84x]

1:12:47 дефект, на лезвии.

[@siguretls]

elle fait peur! précision ?

[@ocintataable]

Restoration?

[@restorationsskills4967]

Thank you very much.

[@tommoore4700]

Pity about the electrical wiring ...

[@Sniperduden]

the chain???

[@sascha5668]

Hier wurden wirklich einige fehler gemacht. Das sind so viele da lohnt das aufzählen nicht. Wenn man es nicht kann lässt man auch besser die finger von solchen sachen weg.

[@restorationsskills4967]

Thank you for your feedback so we can better improve future products. Wishing you and your loved ones good health!

[@stephenvale2624]

Sorry to see the chicken being painted. And no way would i trust that machine near any part of my body.

[@slonvposudnoilavke]

А задний стол на фуганке слабо поднять?

[@restorationsskills4967]

Thank you. Our team of highly skilled workers makes the job very simple

[@davidturner8689]

Poor work on the wiring! Never connect wires like that. Replace with new wires.

[@restorationsskills4967]

Thank you for your feedback so we can improve future products. Wishing you good health