That ticking you're hearing is called the 22R sound
@owenfalconer93983 жыл бұрын
So nothing is wrong with that sound
@ragingbull58832 жыл бұрын
@@owenfalconer9398 Many do it, some don't mine has a bad rattle almost, it needs an adjustment bad, it also happened to me when I started to run thinner oil. A healthy engine usually won't do it but they do make noise.
@DirtyDangleDaryl6 ай бұрын
Some you can adjust to a nice smooth acceleration whine
@iTzDaNiiLo8 жыл бұрын
Theres a 94 Toyota Pickup at home with the 22RE and my goodness that engine has to be one of the best engines Toyota has ever made. Can't express enough how thankful I am for the years of reliable service that truck has given. Things a tank and 298k miles later, still going strong.
@andersfranz53675 жыл бұрын
Nice! Idk why but mine blew up at 170,000 😷
@DirtyDangleDaryl6 ай бұрын
550k Miles and likely dead soon, wish me luck
@CraigArndt8 жыл бұрын
I listened to both before and after a few times, it is definitely sounding smoother and quieter. It was rough to start, but the response is good now.
@groutaone8 жыл бұрын
Strange thing is it seems to have a little more power now but I kinda think that's just my imagination ha ha
@snippits756 жыл бұрын
My 1992 pickup 2wd with 22RE sounds just like that. It's just the way they sound. I don't mess around with doing it hot. I adjust them to 7/11 cold instead of 8/12 hot. I turn my engine over using the crank pulley bolt. My 1/2 drive ratchet with 19mm socket slips right between the bottom shroud easily, and then right onto the crank pulley bolt. A helper to line the marks up on the crank pulley helps it go faster because I can't see the alignment marks laying underneath turning the engine over with the ratchet.
@mxkcrm5 жыл бұрын
Would the same measurements work for the 20r?
@TheEZGZ8 жыл бұрын
The 22R Toyota engines are notorious for the nylon timing chain tensioner wearing out. That's probably what your hearing. If not addressed the chain will rub threw the case and leave a hole. It is common and if you google for it there is an upgrade kit to replace that guide assembly. Good luck. Really enjoy your vids.
@casada708 жыл бұрын
Yeah get the LCE Timing chain kit with the steel guides. best kit you can buy.
@hydroboostoxiaction62717 жыл бұрын
casada70 tends to be louder than the nylon guides but last longer. unfortunately replacing it is a long job
@joshhutch44325 жыл бұрын
I hear no timing chain noise in this clip. It should be more obvious than that. Metal on metal chain noise is louder than valve rattling by far.
@crimpcreep68875 жыл бұрын
eBay, get New cover, oil pump, water pump, timing chain both gears ,all gaskets, guides, seals, all new, $75.
@yanglue6115 жыл бұрын
They say that 1,000 horsepower motors are monsters! Older Toyota engines are true monster
@azkid1108 жыл бұрын
comparing 0:43 with 7:13 there's a good improvement!
@IHcubcadet8 жыл бұрын
What a great little motor. Have heard great things about there longevity. My 02 Tacoma has the 3.4 v6 with Iron block, another great toyota engine.
@crimpcreep68875 жыл бұрын
I wouldn't adjust anything on a high mileage head without a rebuilt head, new timing chain, oil pump, water pump, tc gears, whole shebang. You can buy everything on eBay, including new timing cover now for $75, free shipping! I would yank engine out and do a rebuild. Injectors, everything! I just finished a UZ1 92 Lexus 4.0 V8. Aluminum head and block, was a blast. Sounds great with flowmasters!
@BobTom-e3n7 ай бұрын
So instead of a simple valve adjustment, your solution for noisy valves is to pull the motor and do a full rebuild? Right on. Oh and you suggest the cheapest garbage aftermarket parts as well? Bang on.
@thepyrodude8 жыл бұрын
when I was a kid everyone came to me to work on their Toyota 20r and 22r and the 2tc and 3tc engines....I had a pretty hot Carola 2door wagon and a 2 door car was running a 3tc hemi with an offenhauser dual port intake and dual webber carbs and a header...then I turbo charged it with a homemade blow thru system....they were pretty damn fast and could take the high rpm abuse I did all that before rice was cool lol
@joelcr2508 жыл бұрын
*THE LEGENDARY 22R*
@hydroboostoxiaction62717 жыл бұрын
CR2504life this is a 22re
@gussferretti96655 жыл бұрын
@@hydroboostoxiaction6271 same engine just ecm and fuel injection system
@MartinSage5 жыл бұрын
Also, take out the plugs. When the piston is at the top of cylinder you can adj. valves.
@Tonnsfabrication6 жыл бұрын
Just worked on a 92 PU with the 22 RE and when i removed the valve cover the driver side timing guide was missing and chain was flapping in the breeze. I put the new front cover kit with oil N water pump on it and all new upper gasket kit.
@thelivekennedyssdcaliforni78416 жыл бұрын
do mine now. : )
@Raevenswood6 жыл бұрын
I'm not saying this to be a hater but you can just put the ratchet on the crank pulley from below and make small incremental movements checking along the way ... you can start to tell when it's coming around on the compression stroke because it gets harder to crank the engine and then right when you are near TDC it lightens up. Or if you have someone else available ask a helper to keep an eye out for the TDC mark while you crank the ratchet from below. The shroud is in the way on my 4runner too but I just reach in from below, the extra ground clearance probably makes it easier than on one of the 2wd pickups but still doable.
@SachiWI8 жыл бұрын
On my 97 accord I'd have the valves adjusted and it would sound solid for a few days and then it would be back to noisy again. I even took it back to the Honda dealer and they said there is nothing wrong with it - so depending if they are hydraulic or not is the reason for the noise. I had tried to compare my Accord to an Acura same model year and his had hydraulic and no noise.
@g6qwerty8 жыл бұрын
I notice that changing my cars engine oil quiets down the engine more than a valve lash adjustment dose on my 90 Integra. Its basically got the same setup for camshaft with rocker arms for the valves. Though My car has a timing belt instead of timing chain which might be the source of your car's engine noise.
@veggiepowered6 жыл бұрын
Sounds The Same After ? You Might Need New Timing Chain Guides They Came With Plastic Ones From Factory And The Top Ears Break Off After Awhile
@nathanmccloud13384 жыл бұрын
This guy didnt know a thing about the 22R-E
@pr4runner8 жыл бұрын
Really enjoy your videos. I've timed a 22RE about 4 times. Original Engine was still going at around 365,000 miles but decided that I could replace it for less then free at the moment w/ a new Crate engine from xxxxx. I have an 1985 Toyota 4 Runner with a new engine that has been sitting for over 10 years now. Engine is /was new 15 years ago and ran last in about 2008. (About 3000 miles w/ proper oil changes x 3 during break-in), gas is as old in the lines, tank, pump, etc. Suggestions on a pre startup thing to do? Think I need to pull the cylinders or just spray some oil in there and turn the engine over w/ the ignition disconnected? Also think that all the lines and fuel pump and injectors need to be cleaned or replaced before start up. Engine was not fogged before the project began and got set to the sidelines. ??? Rust bucket build that needs a new body. Thank you for any constructive advice. I already know that I should have been taking better care of the engine during this storage period>
@shawnmrfixitlee64788 жыл бұрын
Toyota web site forums say there is a 10-20% power loss in miss adjusted valves .. True ? I don't know .. But she sounds better ! Thumbs up..
@m.d.4982 жыл бұрын
So when moving down the intake and exhaust how far to you rotate the motor? A full turn back to top dead center?
@ghaffarsultan79438 жыл бұрын
pulling the sparkplug's would have made turning the motor by hand a lot easier and saved you from cranking it with your yellow dot . but I still like the dot reference mark .
@senate20422 жыл бұрын
It fires 1,3,4,2 in that order if you just keep rotating 180. Verify with distributor position. Just a different way to do it.
@dirtbiker_vintage55278 жыл бұрын
Are you gonna do any more long travel videos because those were really cool
@karroome8 жыл бұрын
this sure brings back some sweet memories, but in a carburated form for me;)
@hondamaniack8 жыл бұрын
22r goodness
@keenanleetodd8 жыл бұрын
FYI these are famous for the timing chain to cut through the timing chain cover. Change the chain as recommended. If you think you have a bad head gasket, it will be the for mentioned.
@MrSparkums5 жыл бұрын
Yah, the plastic chain guide goes out on em eyy, dontchaknow.. X )
@PhilipGragg8 жыл бұрын
get rid of the mechanical fan. swap in an electric fan for $30 with a fan controller.. buy the steel guide kit from ENGNBLDR.com don't adjust the valve lash out of spec. yeah, it's only a thousandth but at higher RPMs you might have some floating valves due to the rockers being too tight.. unless you have dual compression valve springs, stay with stock specs. glad you got er cleaned up 👊😎
@michaelovitch8 жыл бұрын
Valve adjustment at operating temp?
@whatsyurprob1584 жыл бұрын
Exactly. How does one adjust before the engine cools down? This is ridiculous. Why isn't their measurements listed for when it's cold?
@keshmo128 жыл бұрын
Great video but I thought you were supposed to do valve adjustments while the engine is cold because the metal expands when it's hot?
@groutaone8 жыл бұрын
Toyota gives specs for hot engine.
@DestroyersGarage8 жыл бұрын
some manufacturers give both hot and cold lash
@andrewford808 жыл бұрын
I thought that also. Learn something new every day!
@brianrb848 жыл бұрын
If nothing else, the engine seems to idle a lot smoother.
@maxnuccio24403 жыл бұрын
Probably your injectors mate! Mine are noisy too, took a bit of getting used to, the timing chain was perfect and I set the valves and still noisy. Put a screwdriver to the injector and boom ticking like a clock. Just how they go ;)
@santosmedina1073 жыл бұрын
How do you solve your problems can you explain a little more because my its sound same its a 1987 toyota pickup 22r carburator can you help please
@yourbeekeeper8 жыл бұрын
Great engine.. Thanks for the video.
@DatBlueHusky8 жыл бұрын
ticking could be the injectors. My subaru ticks but its all injectors
@yaaami908 жыл бұрын
I had the exact same problem on my mercedes, air leak at injector
@groutaone8 жыл бұрын
Good point
@MrDylman558 жыл бұрын
30GB
@4af3 жыл бұрын
The factory in Japan set them at .007/.011 because that's the setting the delivers the best overall power, fuel economy and valvetrain durability and minimizes ticking noise. I used .007/.011 for 485,000 miles and my camshaft lobes, rocker arm pads and the tips of the valve adjustment screws were still unworn - no ridges, dents or flattened spots and virtually no loss of engine power.
@chacholiades3 жыл бұрын
I am curious, how did you know about those measurements? I am reading right now the toyota manual and it says: 0.008/0.0012. Also, did you use those measurements when the engine is cold or service temperature? thanks.
@4af3 жыл бұрын
@@chacholiades I personally measured them on a dozen new '89-'95 trucks including two of my own. Engine fully warmed up.
@chacholiades3 жыл бұрын
@@4af so, engine warmed up and the .007/.011. I will try those.
@eadelfin8 жыл бұрын
FYI, I would have removed the spark plugs and turned the engine over by using the camshaft bolt. The little rubber grommet comes out at the front of the engine.
@thelivekennedyssdcaliforni78416 жыл бұрын
just curious- why remove the spark plugs? i am not much of a mechanic so be gentle, please. : )
@thelivekennedyssdcaliforni78416 жыл бұрын
just saw that someone mentioned it would make turning the motor by hand easier, but why? thanks.
@juansamaniego95186 жыл бұрын
@@thelivekennedyssdcaliforni7841 no compression
@thelivekennedyssdcaliforni78416 жыл бұрын
thanks.
@owenfalconer93983 жыл бұрын
What causes a ticking sound when its trotterling ?
@owenfalconer93982 жыл бұрын
Ok not many mechanics really go into the finer tuning of an engine
@owenfalconer9398 Жыл бұрын
Ok so should they be replaced?
@jordan2mill Жыл бұрын
@@owenfalconer9398 I would
@thenman232 ай бұрын
its loose lol
@owenfalconer93982 ай бұрын
@@thenman23 what is loose?
@tylermormon76498 жыл бұрын
What happened to sand rail
@christucker11134 жыл бұрын
Umm your wrong a 22re is 5degrees not 0 zero is 22r carbed....
@WestCoastRoller8 жыл бұрын
Always RTV the half moon seals or the cover will leak oil.
@hydroboostoxiaction62717 жыл бұрын
West Coast Roller mine never have leaked and I didn't use rtv on them
@reinaldogonzalez60455 жыл бұрын
What is the half moon? West Coast Roller :
@JoshKilen8 жыл бұрын
nice job, you could do it easier, by taking the plugs out
@reinaldogonzalez60455 жыл бұрын
Valves adjustment 7 and 10 cold, or timing chain guides broken.
@4af4 жыл бұрын
Valve clearance has nothing to do with chain guide durability.
@ciskokidd59804 жыл бұрын
Cool Thanks
@MartinSage4 жыл бұрын
Stick with 008 + 012. I would rather hear 'em than smell valves. Also ck the rotor position.
@pseudoprodigy5 жыл бұрын
Sounds more like a sewing machine at the end 👍
@jodytucker44748 жыл бұрын
Sounds like the ole "Toyota tick" to me!!
@sinw.o.k17396 жыл бұрын
I have a 92 Toyota 4X4 SRE 4 cyl had to replace timing chain since then I have the" TOYOTA TICK" its driving me CRAZY!! Anyway to STOP this????
@Sahan10115 жыл бұрын
@@sinw.o.k1739 just drive it buddy
@4af4 жыл бұрын
@@sinw.o.k1739 valve clearances need to be .007/.011 to quiet the tick.
@KIDZKARTBLDER8 жыл бұрын
SAND RAIL ?????
@ziggassedup8 жыл бұрын
That's one method but I use another.
@larrysee73062 жыл бұрын
@2:20. Already bloody😂
@tomchastain61465 жыл бұрын
if you tighten valve cover too much will make rockers noisy again
@irvgotti946 жыл бұрын
Sounds like ur metal rod bearing
@Samson-EC4 жыл бұрын
A majority of folks always skip showing how to install the half moons and how much silicon to use. No different here....jc
@jason-ge5nr8 жыл бұрын
Thats a cool look into the toyota engine. The rice oil looks a lot like regular engine oil.
@DKLGalactus53 жыл бұрын
no good bro
@IHcubcadet8 жыл бұрын
What a great little motor. Have heard great things about there longevity. My 02 Tacoma has the 3.4 v6 with Iron block, another great toyota engine.