Toyota 4Runner Ditch Light Install at RPM Garage

Install Rago Fabrication Ditch light brackets and Baja Design Squadron Pros on a Toyota 4Runner
Baja Design Squadron Pros
amzn.to/2ZFRxZd
Baja Design Squadron Cover
amzn.to/2XCTRgT
Ditch light switch for 5th Gen 4runner
amzn.to/3gq124J
Rago Fabrication Ditch Light Bracket
www.ragofabric...

[@jonnyhalo1041]

Dude, thanks for the detailed video man . Think ima use this when i install mine. Thanks

[@wishiwasboosted7741]

My ditch lights are coming in soon can’t wait to instal them!!

[@harambes_revenge9220]

Thanks for this! It helped tremendously!

[@ao_ross]

Great video and walkthrough but I could barley hear you over the music. I would’ve enjoyed the video more if the music was quieter and your voice audio was louder

[@elochito24]

Thanks for the video, it would be nice if they make the bracket so it also black or matte black

[@vinboughton4751]

Nice Clean job !

[@phillipspracklen5448]

Thanks

[@keithmurray7493]

Ditch the music. It's distracting. Otherwise good info.

[@michaelmanzon4062]

That can be install to my 2011 Toyota Sienna LE?

[@prodipper3562]

Great, clean install!

[@gilquez1881]

Thanks for sharing. Was in the process of installing my ditch lights when I realized that my wiring harness is different from yours. Can you share which harness you used? I have SKU: 640117. Thanks.

[@joehendryx4196]

Great Video, but where did you get this harness?? The one I have is way too short from Baja.. HELP.

[@buggz1137]

Whats something like that go for?

[@shawn7518]

Did you have to cut, trim, or melt any of the plastic on the passenger side to make it fit properly???

[@chad0063]

I was told that with the OEM switch you need to use a wiring harness with a relay, which Baja Designs doesn't have, but I see you used the stock wiring harness from Baja. Does a relay just enable the switch to be lit up while not on or is that statement just false?

[@sponsoredbywifey]

You do not need a wiring harness with a relay. I use the wire harness it comes with but cut off the switch and replace it with the oem style switch. Most oem style switches has 4 wires coming out of it. 1- wire to battery 2- wire to light 3- wire to illumination 4- ground. Wire 3 I usually do not connect.

[@terryperry838]

You do need relays

[@terryperry838]

As far as I know you need a relay. I did the same exact install with Raptor lights and you must have a relay if you use a OEM style switch. Same goes for ditch lights. If you did not end up using one, I want to know how bc our wiring is exactly the same and I blew my first switch bc it did not have a relay at first.

[@sponsoredbywifey]

I’ve installed many without using a relay. Most lights used for ditch lights don’t have a relay in the provided wire harness. If it does come with a relay, then of course I would use it. I wire it the same as the toggle switch but with the oem switch, there’s an extra wire that is used to illuminate the switch. Most customers don’t want that connected so I leave it alone. It will only illuminate when switch is turned on.

[@terryperry838]

@@sponsoredbywifey right. My first OEM but aftermarket switch blew out bc I didnt have a relay in line. Just my experience. Im curious how you wired it no to blow the switch tho. I orig had my raptor light switch to only illuminate when the switch was engaged, but now I add-a-fused it into my fuse panel and now half it lights up when the instrument cluster lights come on, and the other half once engaged.

[@sponsoredbywifey]

@@terryperry838 green wire connect to battery with inline fuse. Red wire next to it goes directly to lights. Skip the next red used for illumination. Black is ground. Maybe you got a short somewhere?

[@terryperry838]

@@sponsoredbywifey its possible about the short I guess but once I replaced the switch, its been fine since. Yet, when I did my ditch lights last weekend, for some reason the led inside the switch either burnt out or??.... bc its not working. New switch on its way.

[@tonethetiger777]

Looking at similar setup to my Rav4/2016 with some Baja Squadrons, could I do everything the same as show here; set everything up wiring, mount the lights, then plug in everything using the Baja supplied wiring W/o a relay, then power everything up?

[@kuowenaquino7732]

Would this work on 4th gen or just the 5th?

[@overlandersnorthwest]

I get some hood glare. Is it my angle?

[@Deme_banks]

Does it come with a bracket or should I buy one

[@rodminford3812]

Where did you find the OEM switch?

[@FvD714]

did your hood shift position any when you took the lower hinge bolt out?

[@FvD714]

nvm i just got to that part of the video

[@khoidinh22]

Where did you tap for the button illumination?

[@sponsoredbywifey]

I don’t connect the wire for illumination. Most customers want it to light up only when the switch is on.

[@igutz5160]

How much would you charge for install?

[@sponsoredbywifey]

@@igutz5160 email me at [e-mail]

[@meghancoughran1982]

Can you tell me what wires you connected to what wires? The 3 baja design wires to what wires on the push switch?

[@terryperry838]

usually the green goes to battery +, the black to ground, and the red stripped wire closest to the green wire, goes to the relay

[@sponsoredbywifey]

Some oem style switches have different colors. Can you email me at [e-mail] and send me a picture of the switch with wires?

[@williamwatkins2538]

Where did you find that OEM style switch?

[@brokenbeauty7578]

Where can I buy the setup from?

[@chrisvldz]

What's the name of the song?

[@chrisharms2064]

Where are you located? I want you to do my installs lol

[@sponsoredbywifey]

Chris Harms West Covina, California

[@oggyandthecockroaches7387]

pwd po bayan sa LTO?

[@kinesiumlegaspi3322]

hi...just wondering how much do you charge for this type of install..tnx

[@RxMuscleStrength]

Really interested in seeing you do this, but this was worse than Blaire Witch Project. Truly... consider buying a small flex leg tripod and set it up instead of trying to work with one hand. It will make the user experience so much better to watch.