Toyota Electric Forklift Would not Lift

[@jeffreyherbert91]

Never work on forklifts but always enjoy your videos and find them fascinating

[@Onecrazytube909]

Always look forward to your videos

[@arniesand]

As always, good informative video, thanks for your time and effort!

[@VideosByAl]

Nice trouble shooting. We have a 5 and 8 series Toyota Electric Forklifts. No electrical problems yet.

[@charliehustle2579]

Love your videos bud. Thanks for the uploads.

[@antoniopagan5536]

Thnaks @forkliftgeek... good info.

[@joseparedes3720]

Thanks for sharing your knowledge....

[@Cosmobrosomething]

I have an issue with an RSS40 Raymond stacker where the up lift and sideshift functions have gone out after taking delivery. I recharged the battery and the issue remains. There is a clicking noise coming from the top right area of the electrical panel every time I try to use these functions. There is a large round fuse located right there, could it be an issue with the fuse?

[@forkliftgeek10]

Everytime you use the hydraulic functions the pump motor should run. If the motor does not run, check if the contactor for the motor engages. If the contactor engages, check fuse and motor brushes. If contactor does not engage, check wiring. If the motor runs but still no hydraulic functions, check the pump. This is assuming your battery is good.

[@juniorandy2409]

Hi there, thank for this video i got an issue with my forklift which is on but have some error codes, AD-2 AD-4 AD-1 that causes the fork to stop moving. really appreciate your advice on this.

[@forkliftgeek10]

These codes are communication error codes between main board and motor drivers, so the answers is yes.

[@juniorandy2409]

@@forkliftgeek10 thanks a lot for the constructive information. any way i can get this fixed please? thank you

[@forkliftgeek10]

@@juniorandy2409 there are lots of possible causes for these codes. It is not as simple as replacing a part. Worst case scenario is that its the motor drivers which are expensive.

[@juniorandy2409]

@@forkliftgeek10 thank you very much sir, one more question did you guys also selling spare parts on forklift. really keen to know. thank you..😀

[@forkliftgeek10]

The company I work for does.

[@sofiareinholdsson1983]

Hi I have a Toyota 15, 1997 year. issue with Contactor not clicking, no contactor. We tried changing the main contactor and computer box but still sometimes the main contactor does not click. the truck is fully electric and the battery is new and good. What do you think?

[@forkliftgeek10]

Check wiring from computer to contactor

[@sofiareinholdsson1983]

@@forkliftgeek10 Does not appear to be a cable break between the computer box and Contactor. We suspect contactor for back which is broken or oxide on contact surfaces. it is possible?

[@forkliftgeek10]

It is possible

[@JasperFSaludes08]

Ser can you help me for my fork lift, 7fb 25, The main contact not contacting, but when i manualy contact the contactor, still have no power trough the motor,, 7fb25 have 3 motors, steering front drive and the lift,all motors not working even if i manualy push the main contact from the battery.. i wish you can help me see...

[@forkliftgeek10]

If you.dont have a code coming up. Check your fuses.

[@JasperFSaludes08]

@@forkliftgeek10 i already check the fuse, and it is good, Can you teach me ser, how to direct the drive motor and the lifting motor,it have 3 wire connection,like 3 phase on ac motor, 7fb25 model of my forklift..i will wate you reply ser bfore i touch anything...

[@aaronvicente7050]

I have a problem whit the e43 code on a gas unicarrier forklift, can you give me a advice on how to fix it?

[@forkliftgeek10]

E43 is a air/ fuel mixture abnormality code. This be caused by a lot possible causes. The O2 sensor tells the computer if the system is running too lean or too rich to be able to properly diagnose this you need to look at what the O2 sensor is sending, but take note that it does not necessarily mean the O2 sensor is faulty. Some possible causes would be vacuum leak, fuel injector, faulty O2, MAF sensor, faulty wiring, etc.

[@aaronvicente7050]

@@forkliftgeek10 Thank you my friend

[@charliehustle2579]

@@aaronvicente7050 had one on Friday. Throttle Flattens out after a minute or so. Code E-43 Or P1816. Ended up being a bad LP vaporizer. Dash readings were 27-29kpa close enough to the specs of 30-35kpa but not good enough.

[@josehumbertomtzbarajas4409]

Hi i have a toyota 8BE20U, with a 69-4 error code. Can you give me a information about this code please?

[@forkliftgeek10]

I'm guessing it's an 8FBEU20. 69-4 is backward tilt lock solenoid open or short.

[@edtharpe1126]

I'm trying to help a friend identify an engine that replaced the Cummings that came in it. I've got some pictures I'd like to send you.

[@forkliftgeek10]

Look me up on Instagram and dm the picture to me. I'll try to identify it or maybe ask someone that would know.

[@edtharpe1126]

@@forkliftgeek10 , how about Facebook?

[@GlobalTradeInternationalBD-y9m]

Good 🎉

[@mariobragaiii4763]

Backyard mechanic

[@BodariMohmad-ik1lg]

error f0-1 toyota