Toyota Tazz Blown Gasket - Assembly

[@1gerard47]

Good teacher, your organized workshop and reassebly us a mirror image of the way i work ,46 years doing a 2E head now /snapped cambelt only broke no 11 rocker/small inlet valve,it was a good point when you mentioned that rear pipe on drivers side for the cooling system and to make sure nothing is trapped in that area when you put the head on ,great video, i taught 3 apprentices.

[@vehiclemaintenanceandrepai3790]

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

[@Mstshepana90]

Great job Mr G i always appreciat your work thanks for always helping us👌

[@tshimologopena.b236]

Thanks for the content, my Tazz has the same problem within the cylinder the rockers are breaking last time I took it the service I had to pay 6k for that whole part and the whole thing wasn't fixed.. If only I knew I could've sent it to you..

[@vehiclemaintenanceandrepai3790]

1st stage - 29nm 2nd stage - 49nm 3rd stage - 90 degrees inlet (hot) .20mm exhaust(hot).20mm best of luck Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE

[@marcmittler2375]

hello l'ami , je vois sur ta vidéo que tu fais un réglage de soupapes a froid ,quel jeux mets tu a l'admission et l'échappement . cordialement

[@vehiclemaintenanceandrepai3790]

intake .30mm exhaust .30mm (cold), when run hot I reset to intake .20mm exhaust .20mm

[@marcmittler2375]

@@vehiclemaintenanceandrepai3790 merci l'ami pour l'info

[@vehiclemaintenanceandrepai3790]

@@marcmittler2375 A great pleasure, all the best to you going forward.

[@jaars911]

Thank you very much, you gave me some great instructions, I have to change crank seal. Im not ready to take engine apart, will leave that to a professional

[@vehiclemaintenanceandrepai3790]

Some jobs are better left to experienced pro's Len agreed, if one lacks confidence for the bigger jobs.

[@mus3310]

Best in the game 👍👍🙌 I'd you with any vehicle I own Really great work

[@vehiclemaintenanceandrepai3790]

Thanks for the support and kind words Mus, appreciated.

[@AbrahamTitus-ki7mk]

Morning.sir.i follow your instructions.i want to know. as you turn the pully by hand and it stuck against a valve what is the problem.thank you so much for your program.

[@vehiclemaintenanceandrepai3790]

Your cam belt timing is out, if the valve is open when the piston reaches TDC then the cam belt is put on wrong, do not force it you will bend the valve, you must check your crank and cam marks it must line up properly. 23:41

[@forgivenessngwenya3222]

great job sir please explain more about setting the tappets

[@vehiclemaintenanceandrepai3790]

It is explained in this video from 14:48 to 19:31

[@FredCarstens-kq1ob]

Thanks for great vid.

[@vehiclemaintenanceandrepai3790]

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

[@AbrahamTitus-ki7mk]

morning sir.i assembled selinder head.cars timing is tdc.this car has a alarm in.o didnt see battery light on dash.plugs has a spark.this car just crank no start.feul looks fine.what can be the problem.tha ks so much.thanks for your good footage

[@vehiclemaintenanceandrepai3790]

cChek the compression (compression test)

[@MichellePilott]

My cam snapped so will my valve b bent sir ? Or can i jus replace cam

[@babelonchabalala1690]

Good day brother.... What is the torque settings for the 2E head...... And also the valve clearance for the tappets please..... Im tackling this project today

[@babelonchabalala1690]

You probably gona respond when im done with the job lol..... But it sounded like u said 29Nm + 90°>>>>> but thanks for the great video of timing marks also.... Gona finish coz car must be finished today

[@luckylesenyeho5237]

Hi. Does a head gasket sealer really work? My car has symptoms of a blown gasket, white smoke, steam and it once overheated! The oil is still ok, it not mixed with water. The car Mazda 1.3 B3.

[@danzeljaftha7842]

Hi sir, my toyota tazz 2004 mode was standing for a while so battery went completely dead but when i jumpstart it and drive around the block and come back home and when i switch ignition off and when i tried to turn it on again the battery went dead again , the dashboard lights didn't even got . What could be the problem advice please 🙏 🙏 🙏

[@vehiclemaintenanceandrepai3790]

It sounds like you need to properly charge the battery outside the car, preferably a trickle charge, if it still has issues you need to replace it.

[@danzeljaftha7842]

@vehiclemaintenanceandrepai3790 will do that thank you very much

[@zd141]

Hello there Did you install a new thermostat

[@jaars911]

my 2e corolla doesn't have one, alot of people say to remove it coz when that thing fails in the close position and you dont have any tools at the side of the road then youre in big trouble, my fan also runs with key on the ON position, the temp sender unit and fan switch stopped working when it came from backyard mechanic, I replaced the sender unit but I just unplugged the fan switch

[@zd141]

@@jaars911 that's why you install original or oe quality parts and have a good mechanic who can tell when your thermostat is about to give up

[@junaidismail1983]

Hi how u doing I have a 2e motor toque the head 29 and 90"

[@vehiclemaintenanceandrepai3790]

check this video on my channel kzbin.info/www/bejne/lWrSm3iurquFhJY I hope that clears it up for you.

[@agbarmia-tn1kp]

I had my cylinder head done at the engineer no taped was set after setting the tapeta and starting the tapeta has a big nok sound what is the the problem

[@vehiclemaintenanceandrepai3790]

Set the tappets and see if the knocking goes away if not you may have a bearing knock.

[@DanaKotze]

Hi what kind of a camera do you use when both your hands are free

[@vehiclemaintenanceandrepai3790]

Hi Dana, I am using a GoPro 4 Silver with a chest strap, that frees up my hands.

[@elroyjacobs3988]

Did you replace the cylinder head or did you just clean it?

[@vehiclemaintenanceandrepai3790]

Cleaned it up

[@nzwakele]

Uncle Gary, I know you shouldn't but in your experience, how many times can you reuse stretch bolts before you should start getting worried wbout them breaking?

[@elliotronald1884]

The rule says new head gasket new bolts using stretched bolts i dont think can have guarantee

[@migueljimenez-no3nn]

Como,se, desalma una caja de Optra tapa amarilla

[@vehiclemaintenanceandrepai3790]

Thank you.

[@migueljimenez-no3nn]

Como,se,desaoma,una,caja,de,Optra,tapa,amarilla

[@vehiclemaintenanceandrepai3790]

again thanks

[@CindyleeDavids]

Hi mr G can you maybe sent your location for me pls I've got big problems with my tazz pls

[@vehiclemaintenanceandrepai3790]

I am in Cape Town. Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

[@agbarmia-tn1kp]

I had my cylinder head don

[@vehiclemaintenanceandrepai3790]

Great.