Transmission Range Sensor - Volkswagen/Audi Passat -Trouble Code P0706-4motion

[@devinvian7173]

Thank you for the informative video. I picked up a lot of useful tips and I appreciate it very much. Have a 2004 passat tdi in the shop now with a P0706 code, shifted hard into reverse and had a dead pedal when in gear. The PRNDL was always missing 4th gear and would sometimes light up as a solid bar on the dash. I checked for water intrusion at the TCM, but found no issues. I then pulled the range selector, using your video as a guide, and then drilled out the rivets to open it up. Cleaned all the contacts and gently bent the contacts up to make a better connection, then lubed it with dielectric grease before bolting it back together. Reinstalled it back on the car and it seems to be working great. I know now that the best way to do the repair would be to replace the range selector with a new one, but just trying to save a single mom some money. Thanks for the great tips. You are very good at going into detail on your repairs

[@ozzstars_cars]

Hey Devin thanks for your comment. Glad the video helped out and you got the car fixed. Feels good to know someone like a single mom got the help she needed. 👍-Glen

[@j.fanning8158]

I used this tech info. video to help me install a new transmission selector switch on my friends VW Passat last week. Your info. was very accurate and I thank you for sharing it on KZbin.

[@ozzstars_cars]

Good news. Your welcome and thanks for the comment!

[@djkutz252]

Do you know any other videos that can help me with this do I have to disconnect the whole transmission before I can drop

[@wellingtonbueno4810]

was looking to do this on an Audi A6 quatro Automatic, no site available. Glad I stumble onto your site, it's exactly what I was looking for after learning not to call it a neutral safety switch but a transmission range sensor!

[@ozzstars_cars]

They call it trans range sensor so the price can be higher!! haha Good luck with the repair

[@cormacmcrandom6164]

many thanks. just ran into this problem and after replacing my tcm and cam sensor my Audi guru dad plugged the car into a computer and boom found this problem. unfortunately he wasn't in town to install and isn't great help over the phone so this video was a godsend. luckily I found the piece for 40$ and everything has been smooth

[@ozzstars_cars]

You are welcome Cormac. Nothing better than having your own personal guru ;-) Take it easy -Ozz

[@tonytellitright9713]

Thanks this video gave me the confidence to do it myself. 05 passat wagon 4 motion

[@pauliekruger7639]

Hope to help some viewing. I am restoring a 03 Passat 1.8t. The first job was my Cam Position Sensor Code, PO 340- 341. This after much testing of electrical connections required a VVT. Big job. LIMP MODE was also haunting me. My hopes were that the VVT would also clear LIMP MODE, but it did not. LIMP MODE is a bit of a catch all warning that something is wrong. It just happens my one symptom was this: If I used reverse, warm or cold, it went into LIMP MODE and would stay until I turned off the car. When I re-started I "had" to put into drive to avoid going into LIMP MODE. I changed this part Ozzstar shows us and my problem was fixed. The exact part, the manufacturer is on Ebay for $33.00 now. Thanks Ozzstar!

[@ozzstars_cars]

Glad the video was helpful, it took a lot of work to produce and edit. Many people have been helped with this video it's a great feeling to me to know that and I thank them for all the generous PayPal donations. -Glen

[@Samuraid77]

you are such a wonderful person for making this video.

[@ozzstars_cars]

Thank you for the comment!

[@StereoIntegrity]

Thank you very much for posting this video. I have an '02 Audi 3.0 Avant that has the same issue and I just ordered an OEM Transmission Range Sensor for it. Already replaced the TCM (water in the floorboard, fixed now, etc) and the problem is pointing exactly to this unit. I'll keep you updated after I get the part installed.

[@ozzstars_cars]

Good luck with the repair. Looking forward to the update.

[@dave4754]

Very well done , thanks when you own one of these darlings you need all the help you can get

[@ozzstars_cars]

That's the truth!

[@tuliooliveira1590]

That is great Ozzstar, very helpful and thanks for such nice instructions.

[@ozzstars_cars]

Thank you Tulio!

[@mortenoshaug1319]

Tank you. Just what i needed. My car Audi a6 2.5tdi quatro go in limpmode. Now i know what too do.

[@gardenstateflatlandb]

Is the ball-end extended hex the only way to access that top bracket bolt? Another video said, "You MAY have to lower the subframe" to get at it. He doesnt show or mention how he got at it. Doing this same job in a few days, and would like to be fully prepared.

[@ozzstars_cars]

Ball head hex or dropping the sub-frame? I prefer the easier faster route.

[@gardenstateflatlandb]

​@@ozzstars_carsI noticed part the mount bracket is ground down. Did you do that for a better angle at the top bolt head?

[@ozzstars_cars]

@gardenstateflatlandb yes sir, just the slightest notch to make life easier

[@gardenstateflatlandb]

Makes perfect sense. Bought a fresh set of ball end hex sockets, and universal joint swivels, and about ready to go on this project. I'll make sure I have a couple fresh grind wheels for the Dremel now too. Many thanks for the reply.

[@ozzstars_cars]

@@gardenstateflatlandb won't need to grind more than 10-15 seconds

[@doug4sail712]

Awesome thanks got it repaired. Lot of work to try and video that portion of the car not much room to move. I left the top bolt in on the transmission support and swung it out of the way to get to the Neutral Switch. I had better luck Getting to the top bolt of the Support from inside the Hood. Thanks Again!!!

[@ozzstars_cars]

+Doug4sail you are welcome Doug. Glad it worked out for ya. Big job just to remove one little switch. Take it easy

[@leonidastg]

Thank you veri much, this was a life savor for me, my Allroad C5 is working perfect now 😀

[@ozzstars_cars]

Good news!

[@russwright8016]

I have a 2003 audi allroad and I cannot reach the top bolt for the heat shield covering the safety switch. Any suggestions

[@ozzstars_cars]

Do you have 1/4" swivel and extension for your socket?

[@bachiistsho2940]

I just finished F125 range sensor replacement on my ‘03 allroad 2.7T 5AT. If you’re referring to the top screw (M10 head) on the triangular heat shield for the aluminum trans support, you don’t need to remove it, undo the 2 bottom screws, curl the heat shield up to remove two bottom support bolts (M8 hex bit), and let the heat shield come out with the aluminum support fitting. (Alternatively, loosening the hose clamp for turbo heat shield on down pipe might give you the clearance for the said top heat shield screw) Of course, the hardest part is the top bolt (M8 hex bit) for aluminum trans support, but I used two universal joints along various 3/8” extensions routed just forward of LHS downpipe to loosen the top bolt (I needed 17” breaker bar to loosen the tight bolt). Hand access for this tool engagement manipulation is through aft of downpipe. Loosen the RHS trans mount (2 bolts), place a jack under AT case just after of trans pan, to raise the powertrain just enough to slide the LHS tran mount out, then you’ll have the access needed for range sensor replacement. Seeing this and other videos, I feel the 2.7T cars may be the hardest to replace range sensor, due to the exhaust downpipe being in the way.

[@jeng.7564]

Thank you for your help. Will look into that. Great video, very helpful. Thank you for your time.

[@ozzstars_cars]

You are welcome, good luck with the repair

[@riamosalice]

Thx for the video. Regards from Paramaribo Suriname. VW passat variant 1.9 TDI, 2002 km 334000

[@ozzstars_cars]

+Eddy thanks for watching and commenting!

[@larrycox2262]

I Think this is my problem gonna try this.Good video thank you

[@ozzstars_cars]

You are welcome Larry. Hope you get the problem fixed!

[@pamkaturi]

Never mind, I got it from your video, it was good video.

[@ozzstars_cars]

Glad you found the answer!

[@luehawj82]

Great video ozzstar. It fixed the limp mode on my audi

[@ozzstars_cars]

That's good news.

[@dwightvoeks9970]

Nice work on the single hand video

[@ozzstars_cars]

Thanks

[@jeldreth0122]

Thank you for making this video.....It was very helpful....Thanks

[@ozzstars_cars]

james eldreth your welcome james. Take it easy - Ozz

[@silasthemanguy8941]

thank you so much sir for making this video it was very helpful exactly what i need

[@ozzstars_cars]

silas themanguy your welcome, thank you

[@drowization]

WOW, great, great video good sir. Thank you.... GOD BLESS you :)

[@ozzstars_cars]

Glad you enjoyed it. Thank you!

[@KeenOnTaka]

Thank you bro, about to tackle this today.

[@ozzstars_cars]

Good luck and let's us know how it goes if you can.

[@KeenOnTaka]

@@ozzstars_carsmy crankshaft position sensor failed so I ended up having to replace this first but am finally on the range sensor now! I have never come across tighter bolts than those 8mm hex. I've got one out so far, have snapped an extension bit for my torque wrench on the 2nd bolt which is a first for me, and you're telling me the 3rd one at the top is the tightest 😅. Good fun

[@ozzstars_cars]

@@KeenOnTaka when those factory tightened bolts break free there is a distinct crack/pop sound that lives in my head rent free. Haha

[@serrgioallonso6093]

thanks this video help me with the same problem 👍

[@ozzstars_cars]

+Serrgio Allonso thanks for the THUMBS UP!

[@cdoutland]

Ozzstar I have 02 jetta that has a five speed tip tronic but my range position sensor seems to be the problem why it's not starting, it's stuck in reverse no matter what gear I select also the reverse lights stay on.

[@cdoutland]

Ozzstar does it require a computer to readjust it or should I just buy a new one??

[@stevengerrrard]

Thank you, that was really helpful!

[@ozzstars_cars]

Glad it helped Steven

[@przemekiwa3443]

Thank you for the video - have the same problem and the same fault code: P0706. Hard time to enter into reverse, often transmission goes into the limp mode with all PRND432 highlighted. When moving the shifter I do not have the highlight moving with it, there is a delay or some of them go in and out almost blinking (saw it on position "4"). I will look for the range sensor replacement and I hope it will fix it! Thanks again!

[@ozzstars_cars]

A Vagcom scan can determine if the TCM is not reading the range sensor correctly. This way you are 100% sure that it is the sensor. Swapping parts that are not broken can be expensive and time consuming. Good luck

[@PszemoI]

I was able to disassemble everything to the point I am stuck in-mating the connector. This car has an oil leak and everything there is black - not much clue how these two halves of the connectors are latching. Would you mind describing how to unplug it? Thanks!

[@ozzstars_cars]

I usually use a small flat head pocket screwdriver to help separate a stuck connector. I dont recall the clip VW used for this one, its been a while. The new part should give you an idea on how the connector plugs in with a clip

[@PszemoI]

I got it undone by looking at the picture of the connector on the O'Reilly's website - it does have a latch - Thanks. btw - do not have the new part yet - I was going to see if I am able to remove it first before I shell out the money for a new part. www.oreillyauto.com/site/c/detail/ODI0/180998/02035.oap?year=2004&make=Volkswagen&model=Passat&vi=5017623&ck=Search_neutral+safety+switch_5017623_4342&keyword=neutral+safety+switch&showStores=true#

[@gerrymurray5914]

Was your PRNDS sometimes flashing when it happens to my Audi A4 2004 I couldn't get reverse and then the PRNDS would flash and then I was able to drive my car in reverse

[@ozzstars_cars]

I don't recall but that is a possibility. Time to diagnose.

[@gerrymurray5914]

@@ozzstars_cars The computer show me that the Transmission Range Sensor was gone and I was getting the code P0706

[@JourneyedAvenger]

What are the torque specs you need to tighten the trans mount and braces to?

[@ozzstars_cars]

Sorry don't recall the specs off hand.

[@louisluigi]

Thanks for the helpful video! I did this job today, cause I had the same error so I inspected sensor and couldn't find corrosion or what so ever. It's faulty anyway, so I decided to open the sensor, just used a drill to disconnect the rivets and open it. It's a very simple device, I cleaned it, bent the contacts a little and sprayed it in with wd40. Then i sealed it wit a kit and placed it back on the gearbox. Job well done, works perfect again and I saved 300 euro for a new one :)

[@ozzstars_cars]

+louisluigi glad the video was helpful, thanks for commenting

[@77northfork]

Great video. Ozz do you know if this DIY would work on the Audi A6 C6?

[@ozzstars_cars]

Todd D thanks, not sure about A6, never worked on one

[@Gerone1]

Thanks for a great video. I’m changing mine now. I’ve reached the sensor. Must the the transmission be in ‘N’ for me to attach the new sensor? Regards.

[@jasonhamilton1727]

Wish you could show how to remove that transmission mount cover that holds the mount I used every tool and my exhaust is in the way

[@ozzstars_cars]

Use a ball head hex socket. Discussed in the video.

[@jasonhamilton1727]

@@ozzstars_carswhat size motor is yours mines 2.8 I had to grind some of that away to get close at a straight shot at no room for that ball hex at all. Got it done with some modifications great video

[@ozzstars_cars]

@@jasonhamilton1727 not mine and the engine is a 2.8L

[@kurtcrafton]

Great vid man. Clear and easy to follow. I'm about to buy an Audi A4 1.8t Quattro for $1000-1300. The current owner said he came home from work and parked it. When he went to use the car again it wouldn't shift into any gear so he bought another transmission from a wreaked Audi (not too sure he bought the right one), but they do have this part in common and he's including it for free. So I'm gonna swap the sensors and also put in a tcm I found on eBay for $70. Hopefully it will fix any issues. Also he says the indicator on the dash never flashed, was never solid, or was off in respect to the shifter position. The car cranks and runs fine and even has an upgraded TD04 or K04 turbo. What do you make of that? Just a tcm and or harness with water damage?

[@glen-ozzstarscars8474]

When replacing the TCM make sure the serial numbers match the original tcm. Different models and years are programmed differently and they may not be compatible. A VAGcom diagnostics will be able to tell you if the TCM is defective or there are specific transmission issues, for example a bad solenoid. Water usually will leave signs of corrosion. Thanks for the feedback, hope this helped you. Take it easy

[@darcygilliard1053]

Hell of a Video

[@ozzstars_cars]

Appreciate that Darcy. The video took a lot of work to film and produce.

[@darcygilliard1053]

Damn sure what I’m dealing with !!!!!! Those Passats are New Born Babies

[@ronbond3777]

I am having a incorrect ratio 5th gear code on my 2004 Volkswagen passat GLX 2.8 lt and when I get it warm the car dash where the gear lights are will all light up where it should be only 1 gear the gear you are in that lights up but it's all lit up and feels like it wont shift in 3rd 4th or 5th gear is there any idea why?

[@ozzstars_cars]

Need to hook up VAGcom software and see what the TCM data looks like to get some form of direction for a proper diagnosis.

[@juancarlosbermudez2434]

Gracias por compartir. Sería bueno traducir a español. Saludos!!

[@ozzstars_cars]

Es una buena idea, siéntete libre de traducirlo al español. Gracias por ver.

[@waledtaha422]

Is that part fits all type of passat? I have same problem with my 2004 1.9 tdi

[@ozzstars_cars]

Always cross reference the part to the vehicle to make sure it will fit.

[@HHTTRRNN]

OK, fixed my switch, did not replace it. I took mine off, drilled out the rivets that hold it together and found two wiper contacts inside heavily burned and fatigued. The manufacturer made the wipers out of very thin spring metal, hence the reason they fail so easily. Anyway, I was wishing I could just repair the switch and not order a new one. The thought crossed my mind to solder a bridge wire between the brown and green leads where it would crank in any gear, but I resisted that urge to defeat the switch. All I needed was a couple of pieces of spring metal to replace the contacts, but where would I find that? I found an old flashlight and cannibalized the sheet metal contact that runs along the inside barrel of a flashlight. It took about 30 minutes with a pair of needle nose pliers, vice grips and a Dremmel Tool, to fabricate and replace both sets of contacts. I have photos if anyone needs illustrations. I reassembled the switch halves using screws and nuts. A confidence test showed it worked well and the metal is much thicker that the original contact. I have been driving it a few days since reinstalling the switch and it works fine. Saved a butt load of money. Thanks to ozzstar for the info on senor replacement.

[@glen-ozzstarscars8474]

That's great that it appears your inexpensive fix has worked. Yes those two wiper contacts wear and fatigue. Thanks for the update and sharing your idea.

[@moehamad5843]

HHTTRRNN hey msn u in cali ill pay you to do mine

[@audiwankenobi361]

I just asked Ozz if cleaning the sensor would work then I clicked on this link and found your comment.

[@mkvsabo]

how did you get the top bolt out of the second heat sheild?? the cat is in the way

[@ozzstars_cars]

Did you watch the entire video or skip? It is discussed in detail, ball head hex.

[@mkvsabo]

@@ozzstars_cars watched the whole vid, and sorry it’s actually the silver heat sheild, i need to use a 10mm socket

[@marcstreiff6067]

Thank You.. Doing this today on my 2005 Audi allroad, so I can get to New England Dust Off @ Thompson tomorrow April 30th... It is not easy to find info on this, my Bentley repair manual is basically not useful for this particular repair.

[@ozzstars_cars]

Good luck with the fix!

[@marcstreiff6067]

@@ozzstars_cars Thanks, back to it this morning, pouring rain last night & since I do not have a garage in my current house, sanity demanded to hold until this morning which is still duck weather but not as bad.. amazing & fortunate how similar much of the layout is between VW's & a Audis..

[@ozzstars_cars]

@@marcstreiff6067 I hear ya, another rainy day here in Delaware as well. 🌧🥺

[@pamkaturi]

What store did you get the part from? What's the brand and SER number of the part?

[@mr7808ss]

Hi I have a 2006 Jetta and I need to change the TCM.Where is the TCM located?

[@miguelangelochoa363]

VERY HELPFULL THANXSS

[@ozzstars_cars]

Thanks for your comment Miguel

[@SleeperJohns]

I got a new motor put on my car. my car started with no problems but will not move. the man that did the work on my care said that the transmission has scratches on it but it also did not give him a code. Do you know what can cause that? he also thinks it just needs reset because the motor was removed. Any truth to this?

[@lebach161]

Ozzstar, did you have to remove the exhaust pipe to access the top bolt on the motor mount bracket?

[@ozzstars_cars]

No I didn't remove the exhaust but if it is removed that will make access to the motor mount bracket easier.

[@lebach161]

Ozzstar Thanks. I just replaced the range sensor on an 03 Audi A6 Quattro 2.7 turbo. That top bolt was quite difficult. removing the exhaust pipe would simplify the process greatly, however as you know that isn't a simple task on this car either.

[@ozzstars_cars]

***** you got that right Leslie, removing the exhaust is a pain in the ass for sure! Glad the vid was helpful and you $aved lot$ of money doing it yourself, awesome!

[@kwakumt623]

Why did u have a change that sensor

[@ozzstars_cars]

As the video discusses the defective range sensor was putting the engine into limp mode.

[@wingsrus720]

@@ozzstars_cars the engine or transmission is in limp mode? I have 04 vw touareg dash reading PRNDS it drives in 3rd gear and does not switch gears. Could this be a similar fix.

[@ozzstars_cars]

@wingsrus720 duagnose using VAGcom software to help guide in the correct direction.

[@wingsrus720]

@@ozzstars_cars thanks

[@ThyAnarchist87]

Ozzstar I have a 98 passat and from what I could tell everything was the same. I went to start it the other day and it didn't start. After messing around I found that if I turned and held the key in the start position then shifted into Neutral it would start. I think I'm a smart fellow so I thought it was the neutral safety switch. So I changed it and when I did it caused the gear indicator to go black with clear letters. It wasn't like that before. I had to problems switching the part. It still won't start in park and still starts in I move it into Neutral while holding the key in the start position. Any ideas or help would be greatly appreciated.

[@rockpastor]

I have a 1998 Passat 2.8 V6 4 wheel drive with automatic tranny. It is in limp mode right now and with the fuse in for transmission it is locked in P(ark). When you take the fuse away it allows you to move the shifter. We have changed the brake light switch, checked the computer under passenger floor and no water there. Our codes said P0705 and P1746. Right now we do not know what to do and for us taking it to the local Volkswagen dealer for service is not an option because we are broke. Thankful for answers and blessed for help :)

[@electo2006]

Hello, i followed your video on my AUDI 2003 AVK 3.0 and there is no switch on my car. I getting a code from vagcom saying replace range sensor.

[@thar3allee217]

Hey I have a 2005 Volkswagen Passat sedan v6 and my car starts and changes gear just won’t drive or reverse could this be the issue ?

[@ozzstars_cars]

Get VCDS software and check for trouble codes. Good luck

[@ikrammohammed1837]

also when changing this what is the cable that needs adjusting and also does it need adaption

[@ozzstars_cars]

what cable? this is electronic. A good service manual will be helpful

[@ikrammohammed1837]

Ozzstar i just was checking online and it stated the cable need to be adjusted and then will need a adaptation abit confused

[@ikrammohammed1837]

Ozzstar if you go down on your post comments i have wrote something if u can read that and come out with something that will be great. it says passat 2004 1.9tdi auto

[@franciscoserrano1120]

Hi, I have question after replacing the Transmission Range Sensor I was testing that it work , I didn’t put the bracket before I turn car on to test it( didn’t know it had to be off) It work fine when car was off but when car is on I put in drive and the MPH goes up to 20 mph without pressing gas and transmission makes a noise, sounds like gears. What could happen if I checked sensor by turning on car and put on drive , and bracket wasn’t on yet??? Please help

[@brandysmanlarry]

Can you please tell me what size tools I will need please? Please. Google won't tell me.

[@johnny23457]

Would this be the same for removal and installing on a 2003 Audi A4? Thanks

[@jeng.7564]

I think we have the same problem bc our car won't switch to rear and they told us is not the transmission . How much did this part cost and where did u get it from?

[@ozzstars_cars]

Purchased online years ago, sorry cant remember the cost but it wasn't cheap.

[@tylerm3103]

After replacing do you need to reset anything to take it out of Limp mode ?

[@ozzstars_cars]

It should not go into limp mode if the repair was the correct diagnosis.

[@jeng.7564]

Thank you. Would you be able to tell me if this would be the problem to our VW Passat 2000 bc it takes a while for it to shift to reverse and it jolts when it finally goes to reverse. This only happens with reverse, everything else (parking, drive, etc) works fine

[@ozzstars_cars]

The TCM needs to be scanned using VW software called VAGcom. This will help find direction to the problem.

[@martinee4901]

ZF 5HP19 Transmission Upgraded Pressure Regulator BMW VW Transgo (SK5HP19-PR)* This bit wears out & lets fluid past it so it wont let the gearbox shift out of one gear & into the next, then when it does, it does with a bang. Im replacing this part in one car with this problem soon. And the TCU in another ( stuck in 4th, default setting, wet TCU). And another im replacing the TRS in ( all gears forwards, no reverse ) I will see how it goes & report back.

[@hwingerrr5680]

This is pertaining to an Audi A6 instead of a Passat, but if it's similar: if the transmission operates normally, would it rule out the transmission range sensor as a problem if the gear indicators don't light up the gear display on the center console? The back light LEDs are illuminated evenly and dimly, but changing the gear doesn't brighten up the one for the gear position as I expected. Any good way to see why the gear indicator doesn't light up?

[@ozzstars_cars]

Best thing would be to do a VAGcom test to determine the issue. It may be an issue with the shifter knob, there is a magnet that moves when the gears are switched. If that is malfunctioning then the indicator light will not change on the dash. Hope that gives you a direction to start the repair

[@hwingerrr5680]

yes, turns out the magnet embedded in the rubber mat is used to activate the Hall effect sensors Audi used to detect the position of the gear shift lever. The led backlight indicators now light after installing the mat properly. Still have the problem with all the dash gear indications lighting up in reverse video though, which is supposed to be a trouble indicator. Don't have a vagcom scanner unfortunately.

[@davidhenriquez9562]

i have a passat 2.0t.it seems to lag on acceleration.i notice like a kick sound.idk where it's coming from.are there tranny normally crap.i would think a car with turbo would need a manual tranny to pull enough power for the turbo system.idk i'm totally new to these cars.

[@OscarMbhense]

Where can i buy a transmision sensor for my b5 awt engen?

[@ozzstars_cars]

Search the internet.

[@Sauce.response]

THANK YOU!

[@glen-ozzstarscars8474]

you are welcome Juan, take it easy - Ozz

[@sicolife]

Would this cause your transmission to do absolutely nothing when you put it in gear like it’s like the engine is not connected to the transmission??????

[@ozzstars_cars]

Puts the trans automatically in 2nd gear.

[@sicolife]

Ozzstar yeah it won’t do anything. It won’t stay in 2 unless I hold it there once I let off it goes to 3 Plenty of fluid, the car had water in the floor board, I opened the tcm and no No corrosion no corrosion to the wires or connectors

[@sicolife]

Also I don’t hear anything engaging when I put it in gear

[@ozzstars_cars]

@@sicolifescan using VAGcom software, hopefully that will give you direction to the problem.

[@MyAlhak]

Hello I wanted to know I have a Passat 2003 a 1.8 turbo can I find a part user or it takes nine pieces

[@jdunooo]

hi ozz very good video I had a question before my fiancé touches anything we have a audi a4 1.8t 2003 an today he tried to reverse it an it didn't want to go into gear then he went forward an it delayed now I had noticed that on the dash the prnd is a solid light but it blinking idk if its the sensor or something worse an Im having trouble finding out what could be involve with that .

[@glen-ozzstarscars8474]

You need to get a VAGcom test for your car. It will tell the technician what is going on with the transmission. Good luck and thanks for watching

[@HHTTRRNN]

My 2003 Passat is intermittent with cranking. Sometimes I can get it to crank in Neutral by sweeping the shit lever through the gears. It will not crank in Park. The dash board indicator lamps light up correctly when I move the shift lever. Does this sound like a Range Sensor problem? Is there another neutral safety switch in the circuit?

[@glen-ozzstarscars8474]

Have you checked the TCM? The transmission control module can be diagnosed by having a VAG.com test completed. This is software specific to Volkswagen. Check to see if there is moisture under the front passenger side floor board carpet. There could be corrosion in the wiring or circuit board if that is the case.

[@HHTTRRNN]

ozzstar Yes, it had moisture under the carpet. Not much but damp with a slight puddle maybe 1/8 deep on the bottom. I was occasionally getting a limp mode from the transmission before drying that up. The TCM showed no evidence of having gotten moisture inside, so it must have been a wire harness shorting out from moisture. In conjunction with this limp mode, the radio would stop making sound, although it appeared to be operating normally. Hey thanks for the quick reply. Any other ideas?

[@HHTTRRNN]

ozzstar BTW, I have a Vag-Tacho system for programing keys etc. Is that usable for the Vag.com software?

[@glen-ozzstarscars8474]

HHTTRRNN hopefully i can locate and post the video I have that shows where to look for corrosion in the wiring harness that leads to the TCM. The splice can corrode from the moisture and cause problems like you are describing. Sorry for the long delay response, I just saw your message.

[@EduardoOrtiz-tt4nx]

Hello there, I have a jetta 2009 and when I have a long ride the transmission doesn't make the changes correctly.

[@ozzstars_cars]

Check the TCM data using a VAGcom scanner.

[@poppgreg5390]

Is this the same for a 04 a6 quattro?

[@MrChristophersrowdyadventures]

Hello, Great video! let's me kown what I'm up against. just a quick question. Did you ever take the old sensor apart? And if so did it look like it could have been fixed? thanks, Happy new year 2017!!

[@ozzstars_cars]

Yes i took the old sensor apart. maybe i should post a video on it. It ended up being a couple of worn copper contacts. I imagine it could be repaired but is better off being replaced since it's such a bitch to get the sensor off and on. Happy New Year to you as well Chris, thanks!

[@larrycox2262]

Is it possible for a Range sensor to be bad on an 03 1.8L turbo and the check engine light doesn't come on ?I changed out my Transmission and the shiftier won't physically go to 2 also I have to wiggle the shiftier to get it in reverse.The lights on the dash are out of sync with the shiftier.

[@ozzstars_cars]

Trans range sensor does not set a check engine light. You need to have a VAGcom scanner to diagnose the issue including the TCM, which will tell you whats going on with the transmission. Look at the mechanical aspect of the shifter by taking the center console apart. There are some small parts in there, not fun trying to get everything lined up.

[@larrycox2262]

I replaced the Range sensor and it is doing fine.I discovered the Shop that put the Transmission in left the bolt that hold the cable loose and didn't adjust the cable.Thank for this video it helpped me a lot.

[@shawncarson6773]

I have a problem with my 2001 Allroad 2.7T Automatic going into reverse. When placed in reverse it will roll slowly but when the gas is pressed all it does it revs up. Research stated that it would be the neutral safety which which is also known as the transmission range sensor. No problems with the dash light, just doesn't reverse. Do you think that this could be the culprit?

[@ozzstars_cars]

Shawn Carson You need to hook up a scanner to the vehicle using VAGcom software to determine the cause of the issue. Find evidence then repair the problem. Take it easy - Ozz

[@moehamad5843]

Ozzstar im having same exact problem everything is running fine except reverse jus rolls back very slow but soon as i step on the gas it jus revs up all other gears r fine PRND illumination on dash disappears and then appears but when its gone is when i seen to have problems

[@mirokrivak8852]

First thing, make shure that ATF level is ok. 90 % of shift problems of Audi VW cars with more like 120k miles . Do ATF service [filter include] every 70 000 miles. Level test- engine must run, slight overflow of ATF from filler. [car in air] 1997 Audis and newer-use Audi ATF [no Red Dexron ll]

[@randystickrod1168]

Question for you: I have a 1999 Beetle that won't start. It shows that it is in drive on the dash, and I can move the gear shifter out of park without stepping on the brake. Do you think the TR switch is my problem?

[@ozzstars_cars]

I wish I had the answer but sorry I don't. Would be best to look at a diagram of the shifter knob and range sensor to see if the are related. I have never worked on a modern Beetle.

[@johnnycolorado4698]

Just recently replaced my range sensor thanks to this video and my gears are working i disconnected the battery for 5 minutes in order to erase check engine light which worked but when i took it to have it smoged the machine gave out the same code p0706 any ideas why

[@glen-ozzstarscars8474]

Is the car your working on a Vw? If so, did you confirm the range sensor was faulty using VAG.com software? This will also tell you if there is any issue with the TCM which controls the transmission. Make sure the sensor is properly plugged into the connector and there is no corrosion on the harness side of that plug. After the repair, clear codes using a scanner. It takes a good amount of driving on the Passat for the TCM to 'reset" after a battery disconnect. ECM/TCM has to go through many cycles of driving before it will be ready to pass an emissions test. Good luck and post your final results if you can. Thanks for watching Johnny

[@ikrammohammed1837]

ozzstar hi i have a passat 2004 auto 1.9 tdi highline. i got this issue, morning start if i put the shifter lever from P to R the lever is on R and it takes a 3 seconds or so for the dash selector to engage to R and it clunks into R which causes all the selectors to light up and some time throws up the engine management light so then if i put the shifter lever back to P turn the car off and then restart its fine but engine light stays on. the only thing i will notice when driving the lever is on D and if i put in on N then R it will show the selector on dash light up P for split second and then go to R its like it skips R goes to P for split second then back to R but doesnt go on limp mode. diagnostics codes p0706 impaulse intermmitent f125

[@ikrammohammed1837]

??

[@mustafaabbas2477]

Hi Ozz I have an Audi 2001 A4 B5 and the PRND flashes sometimes when I run it, usually it doesn't happen in the morning when I start my day, it happens later in the day(late afternoon or night). However, when this happens it just runs okay, just a slight problem with the sensors when I go reverse. Not beeping properly. Do you think the problem is most likely to be the same as you explained in the video ?

[@ronbond3777]

My issue is my 2004 Volkswagen Passat GLX 2.8 V6 30 valve front wheel drive automatic transmission started to bump between 35 and 45 miles an hour I replace the transmission pan because it had some dents and put new transmission fluid in it now it rides smooth and doesn't bump at 40 miles an hour or so but it will not go into 3rd 4th or 5th gear I'm not sure what caused that it didn't do it before and the bumps between 35 and 45 miles an hour wasn't all the time it was once in awhile when I took the old transmission pan off it only had get this less than 1 quart of transmission fluid in the transmission so I filled it until it started dripping back out with the car in neutral running thought everything was okay until I got on Highway and it will not cycle into 3rd 4th or 5th gear I had a p0735 code which side was also caused by low or dirty transmission fluid any ideas on what is going on?

[@ozzstars_cars]

Ron Bond those transmissions require a very challenging way to properly fill them. Did you use the VW trans fluid and make sure the solenoid connectors were making a good connection? VAGcom check the TCM.

[@ronbond3777]

Ozzstar I want to Advance Auto Part with the transmission fluid number was a g 05216 to A2 number something along them lines and I use that to fill it for Volkswagen transmission fluid but I followed a step by step video on KZbin on how to do it so I am assuming I did something wrong

[@ronbond3777]

Ozzstar only thing I did was drop the old transmission pan and transmission fluid filter cleaned up the bolts on the transmission pan reuse the transmission pan bolts put the new gasket on new transmission pan on with the filter back in the spot that the old filter was in and then filled it up to where it dripped a little lowered the car down started the car put it in neutral with the car running and filled it until she started dripping back out put the plug in let it sit for a couple minutes with the car running in neutral and then took it for a drive around the block before I cleared the transmission code with my reader it seem like it was hesitating going into first gear very slow even with pedal to floor then I clear the code and it seemed fine on the back roads then the next day I took it on the highway and I was about 5 grand to 6 Grand RPM which felt like I was in 2nd gear I tried going to the manual shift up and down to the right of neutral and it will not go into any of the gears even down or up it would only go when I'm in Drive at a dead stop I will shift at 2nd gear around 35 miles an hour which seems very high so I'm not sure what is going on but didn't have any of these problems before only a small bump around 35 to 45 miles an hour before doing the pan replacement and fluid but it only had less than one quart of transmission fluid in it when I drop the pan I bought the car used for in everyday driver

[@edibkeskiner7890]

Dude, thank you for upload. I have 04 tdi automatic passat. I found the piece from dealer but it was expensive and my dealer said to me i need 10 plug one. In amazon i found the exact piece but the piece has 9 plug. I am really worried about the possibility of buying wrong switch. What do you think about that? Will it be a problem if i use 9 plug instead of 10?

[@ozzstars_cars]

Yes, it probably won't work correctly.

[@edibkeskiner7890]

@@ozzstars_cars the thing is i send my chasis to seller and he said 9 plug is compatitable with your car. Dealer says 10 plug. 10 plug one cost five times higher than the other one.

[@edibkeskiner7890]

@Mason Gilbert thanks for your answer dude, i actually forget i wrote this comment. after i write the comment i looked the photo that my vw dealer gave me closely, so the situation is exact same with your comment. there is a 10 spaces but there is 9 pins and i bought the part from eBay from OEM part producer for 70 bucks.

[@edibkeskiner7890]

@Mason Gilbert www.ebay.com/itm/NEW-SKV-96SKV101-FOR-VW-AUDI-Neutral-Safety-Switch-Range-Sensor-01V919821B/273372557147?_mwBanner=1&ul_ref=https%3A%2F%2Frover.ebay.com%2Frover%2F0%2Fe11051.m43.l1465%2F7%3Feuid%3Df499dc46338b4c9aab5a976099b62465%26bu%3D44966441870%26segname%3D11051%26crd%3D20200312142808%26osub%3D-1%7E1%26ch%3Dosgood%26loc%3Dhttps%253A%252F%252Fwww.ebay.com%252Fulk%252Fitm%252F273372557147%26sojTags%3Dbu%3Dbu%2Cch%3Dch%2Csegname%3Dsegname%2Ccrd%3Dcrd%2Curl%3Dloc%2Cosub%3Dosub%26srcrot%3De11051.m43.l1465%26rvr_id%3D0%26rvr_ts%3D26132e831740a16d7b9516d1ffe81b4d&ul_noapp=true&pageci=36c51fd7-2eaa-4b40-92d0-439a6b23dcd4 this item dude.

[@edibkeskiner7890]

@Mason Gilbert i am actually Turkish. our currency's - Turkish lira- exchange rate for dollar is 7 to 1. so i have to dig up good deals.

[@papichulo8442]

Having a problem taking the connector off?

[@ozzstars_cars]

Squeeze and pull.

[@papichulo8442]

Thankyou I got it off, great video!

[@randyramos2349]

hey I had a question about the range sensor, are they the same w a audi a4 s line 2006 2.0t

[@ozzstars_cars]

Not sure of the part number, you will have to cross reference

[@randyramos2349]

Oh ok. The code the throws me is p0706

[@rickbarteebartee250]

Randy Ramos

[@iamyzdemon5717]

Hey man I got a 98 Audi a6 2.8 Quattro. Obd2 said something about a trans sensor (PRND432) car runs and drives fine but sometimes it will rev high into next car like holding a clutch too long my car is an auto so I know its not me lol. Idk how much you know about these but my tiptronic or triptonic don't work anymore so that's why I thought sensor and it came up. Also my car is misfiring because my coil pack failed but I replaced coil packs plug wires and plugs now I got spark in every cylinder and I have compression in every cylinder so what's another thing to check fuel injectors? Or do I just need to clear the codes of the computer? Is there an easy way to do that? I do not have a code reader so I can not clear it. Please lmk thank you happy thanksgiving EVERYONE STAY SAFE!

[@orojv22]

Where did you purchase the TR sensor from. I've been looking online but cant find anything.

[@ozzstars_cars]

Enter the part # i give you in the video, you will find it online, use google.

[@dorian898]

I have a 2004 jetta 1.8 t, first I have a problem whit the 2 gear slips ,but every other gear, was working perfectly, so I dice to buy solenoid sensor, for the tectonic gear box, I replace old the sensors, everything was good the first day, but the second day, I star the car, and the reverse wasn't working, did u think this be the problem

[@ozzstars_cars]

Do a VAGcom scan, that will give you direction to the problem

[@joshwool6813]

Drain Trans. Fluid... fill with low viscosity . I had same issues, this fixed it immediatly and the trans. tan best since i've had it. could be the TCM is wet, i hedart this is a big issue also, but id try fluid first mate.

[@djkutz252]

Do u have to disconnect the transmission before removing it

[@tonytellitright9713]

No

[@tonytellitright9713]

Just the bracket and if you got heat shields those lol mines didn’t have em

[@Warborne_fool]

@@tonytellitright9713 man I'm going to attempt this,this weekend and I feel way over my head.

[@Coach-Sasuke]

will this video be able to work on an audi a6 2008 fwd I have the same code

[@tengzturiagaiii3185]

Could this be a reason why transmission wouldn’t go on third gear?

[@ozzstars_cars]

Possibly

[@tengzturiagaiii3185]

Or vavle body?

[@ozzstars_cars]

@@tengzturiagaiii3185 sure could

[@tengzturiagaiii3185]

Thanks i’ll look into it

[@whatdoesthisbuttondo5647]

Hey bro I switched the automatic gearbox for a manual, I have vs passat 2000 2.5 v6, everything has been changed but I can't find a solution for the revolutions it wouldn't go more than 2000 revs per min, maybe you know what is the issue?

[@ozzstars_cars]

Start by using a scanner to check for trouble codes.

[@cedricsimpson6860]

I have a 97 audi Cabriolet no matter what gear i put it in r,n,d, it still drives forward. For example if I put my car in neutral it would display neutral on the dash but when I hit the gas it was still drive forward and it does this in reverse as well any ideas of what this could be

[@martinee4901]

Check that the TCU isnt wet. If it is, replace it.

[@vanessawilliams8840]

i have a 2001 vw passat v6. the tcm was replaced, 30 min later engine light back on the car still shift hard when place in drive. what else could it be?

[@ozzstars_cars]

it could be one of a hundred things. You need a scanner with VAGcom to help diagnose the problem

[@kailasmurf1]

I will thanks 🙂

[@masudkarim5017]

vanessa wil ms

[@masudkarim5017]

vanessa williams

[@gnigill3155]

can anyone tell that where can i get this sensor ..i looked everywhere but couldnt found new one or old

[@ozzstars_cars]

The link is pinned at the top of the comment section and also in the description box.

[@gnigill3155]

Ozzstar's Cars thanks .. i found it but its expensive

[@Sandrakarina]

HI, my bf is trying to change the range sensor but he's stuck on the cover, i think he needs a special tool to remove an upper allen screw, i went to my local autoparts store as well as autozone and i am not able to find the 8 mm allen ball head, is there any other way to remove it!?? help please!!

[@glen-ozzstarscars8474]

Hi Sandra, that top allen bolt is a tough one to get out. You can purchase ball head allens at Harbor Freight or Sears. Swivels with just a short allen key might be helpful. Good luck and thanks for watching

[@borntoashes]

ozzstar Thanks for helping me out, i finally got to change the range sensor (bough one from the yunk yard) still the PRND came up, im not sure where to go from here, i chage the tranny fluid and filter (about 6 and 3/4 quarts) any help would be greatly appreciated :)

[@ap6media673]

hey i really need help right now so today my car 95 audi a6 c4 started but like really slow but it kinda did that once in a while so thought it was normal. and whent to store and it started normal then i wehnt to go pick up my sister and it dint wanna turn on ran checked battery it was good terminals and everything so i turn the key and it will not start seems like a sensor is not letting the car crank and im thinking it could be this neutral sensor? i had been expiriencing hard shifting but not so often and reason why i say i think its this sensor its because i put it on park then woulnt start but when i crank and then switch back i can feel something pop in my shifter

[@ozzstars_cars]

A VAGcom scanner is what is needed to help find the issue. GOod luck

[@buddyanddaisy123]

How much $$ for a new module?

[@tonytellitright9713]

Oh and I found it much easier to only remove just the transmission bracket

[@ozzstars_cars]

Whatever works best is good in my book.

[@daevdel2993]

hi bro, i have a volkswagen cc 2010 sport 2.0 a/t dsg.. ive been trying to find a neutral safety switch that would my car but all i got were the ones for 2009 models. would you mind giving me a hand on this? i badly need to order it online. i would appreciate if you could provide me a link or a product code or a picture of how it looks. thanks bro. awesome video by the way

[@ozzstars_cars]

Your local dealership can get you the correct part number....that will help you

[@daevdel2993]

thanks bro! i have finally discovered why my reverse acted up. I did the DSG service with my vw mechanic and wuulah! reverse is kickin' back on baby! smooth as before. If you guys are having the same problem- just do DSG service- which means you have to trash your old gear filter and load up your gearbox/transmission with fresh vw transmission fluid. Problem solved!

[@ozzstars_cars]

You need to do a search online once you have the part number for your particular model.

[@moehamad5843]

hey was your reverse going out and coming back in? and whats a dsg service and how much did that run you

[@daevdel2993]

Moe Hamad so far my reverse has been working well since i changed my transmission fluid and filter. DSG service means you have to change transmission fluid and filter, have you done that yet?

[@miguel64217]

buenas amigo tengo una falla en mi passat 2.8lt v6 4 motion, el carro esta en una sola velocidad, al arrancarlo avanza muy despacio porque parece que esta en 3 o 4 velocidad, y al ponerlo en retroceso da un fuerte golpe al igual hacia adelante. tampoco me marca en el tablero las velocidades y se quedo en la D, asi mueva la palanca para cualquier lado. le cambie el selector de cambio y sigue igual, porfavor necesito su ayuda ya que en mi pais no saben mucho gracias. hello friend, have flaw in my passat 2.8lt v6 4 motion, the car is in one speed to a very slow start it because it looks like this in 3 or 4 speed, and put it in reverse gives a blow as forward . I also mark on the board speeds and stayed in D, so move the lever to either side. will change the shift selector and as usual, please I need your help because in my country do not know much thanks

[@edwincastaneda7222]

Hola tengo el mismo problema con mi carro le encontraste solución a Tu carro gracias

[@lloyddsouza2798]

After replacing the TCM THUS IT requires any codeing. because my reverse sensor stop working.

[@HCpanda_573]

Hi Ozz. Great video! We have a 2003 VW Passat that we suspect needs a new neutral safety switch. Before we get into the project of replacing it, we want to be sure that is the problem and not the transmission itself. It clunks when starting in reverse, then goes into limp mode when shifting into drive. Any thoughts on how to know for sure if it's the neutral safety switch or a transmission problem?

[@ozzstars_cars]

Yes the trans will clunk when this problem exists. A VAGcom test will determine what the cause is. You are experiencing similiar symptoms this car once had. $40-$90 for a VAGcom diagnoses to be sure! Take it easy - Ozz

[@laziboi519]

My mount has like a cover or something on the bottom how do I get this off

[@adrsilviu2938]

PantherZL1 you have a screw on the top of it

[@laziboi519]

@@adrsilviu2938 figured it out I wasn't sure because everywhere I looked online was showing a completely different mount

[@adrsilviu2938]

The car in the video is an older model. Mine has a cover as well2003 model. Is a nightmare to replace this sensor. Need to be very patience

[@laziboi519]

@@adrsilviu2938 mines an 02 a nightmare it is 😭but once it's done I felt like I accomplished mount Everest

[@rennasou3823]

I have a 2002 Audi A4 sedan automatic transmission and my car won't move. It starts up, goes in to revs nutreul and drive but when I step on the gas pedal it will not move. Not even on reverse. Can some one please help.thank you

[@joetorres3996]

I have 03 passat have some transmission problem sometimes I can run car for a while and I can get on it and it won't shift I turn it off and back on and it will work fine help

[@edkes12]

I have 2002 VW Passat and my neural safety switch went out I switch the switch but I try to cut my car on and It want start

[@feritsd7357]

Passat b5 otomatik şanzıman uyumsuz sinyal arasıra arıza 00652 kod veriyor ve arızayı bulamıyorum yardımcı olursanız sevinirim

[@rogelioaguirrremendoza9536]

Hello,Me apárese el código P0732 y el P0730 marcha de cambio errónea es necesario cambiar el sensor