Tri Toon build pt2. “ custom transom and 3rd toon finished”

[@NCFishingandOutdoors]

That's gonna be an awesome setup Justin. Lookin forward to seeing more of the build.

[@dalehayslip5711]

Looking good good luck with the build

[@CatfishWeekly]

Can't wait to see the finished product!!!

[@richardshook8645]

Looking good!

[@Derik-j9h]

Awesome Can you post the specs and pics of the inside of the transom? I am building something similar

[@alandillemuth1991]

Would love to see an update on this project!

[@ou812axxx]

love the project .I have a trytoon just replace the back I beam have a 150 on it was starting to sag. just some info make the transom as stip as posable .love my pontoon . cant wate to see you finish it

[@teamwampuskatoutdoors4275]

About the get started back on it the end of this month. Finishing up a total house remodel had to dismiss up the honeydo list then I’m full blast in the toon!!!

[@JohnHawkinsLV]

Love your mods! I have a 24' set up almost exactly the same as yours but smaller 23" outer toons and 25" center and exact transom mount as yours I pulled the center toon 24'' back to move my moter out of the inset the transom will mount the motor directly even with the outers and like yours a full back deck Question is what degree angle is your transom plate set? And is your Center Toon mounted flush level with the top of the outer toons or set above or below or centered exactly? You set your transom to place your moter 4" back of your outers I assume to keep the prop in still water I maybe should move my center back another 5" for the same reason I appreciate and like your videos and thanks for the offer to help with my questions your a Southerner and a Dam Good Man Thanks Hawk 😎 👍🏻🇺🇸🇺🇸🇺🇸 🇺🇸 🇺🇸 🇺🇸 🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸

[@teamwampuskatoutdoors4275]

Not sure about the transom angle but I’ll def check and let you know. My center toon is sitting level with the tops of the outer toons. I’m also adding a jack plate to the center too which will add 5 more inches to the setback of my motor. I’ll have more videos soon. Workin on the trailer now. I appreciate the comments and I’ll try my best to keep ya updated on any issues I run into

[@JohnHawkinsLV]

@@teamwampuskatoutdoors4275 Thanjs everyone else I've talked with or asked even the pros are telling me it's far to much weight that far back on a boat with the motor inset into the deck? I'm no engineer but I'm a hell of a lot smarter that those idiots just trying to part me with $80,000 for something they have in stock? Hahaha that will be a Cold Day in 🔥🔥🔥 Fly Low and Thanks Again Hawk 😎👍🏻🇺🇸🇺🇸🇺🇸

[@LeafFWD]

Are you going to put the motors in the rear of the pontoons or between them?

[@ddamion1801]

Hey I’m installing a center toon. What’s the best advice could you provide in regards of me centering that toon??

[@teamcattracker6822]

What’s the reason of the center toon being bigger than the outside toons? I like how you did it I was looking at doing it to mine. Just got me puzzled why all three toons not being the same.

[@teamwampuskatoutdoors4275]

Honestly it’s the only decent toon I could find at the time but after doing some research “in theory”, after I get the lifting strakes put in witg the bigger motor the boat should get on plane and run mostly on the center toon. From what I’ve read it should handle more like a v hull boat and increase mph and gas mileage. I hope it works. We will see.

[@JoaoAmadoTV]

How many Weight can it hold on top?

[@boltinhousejewelers]

can a 8 foot pontoon be converted to a 10 foot any knowledge

[@catfish0427]

Any updates on TriToon conversion

[@prettyboyexclusive6614]

You’ll think he would make one more or someone else 24🦶

[@teamwampuskatoutdoors4275]

I’m Pretty sure he’s totally retired last I heard