Setup AASD-15A parameters for use with AMC-AASD15A controller

[@Simlife101]

@Thanos Motion Electronics Hi Thanos 3 of us who had issues with the Rs Mega kit all found that the parameter PN-83 was set wrong for our countries it should be set to 200 but they all arrived set to 100 could this damage the drives? And could this cause issues on the system? Is it possible to let Eracing lab know their drives are being sent with the wrong alarm parameter PN-83 because this is an alarm so it’s there for a reason so setting it incorrectly seems strange to me

[@tronicgr]

@@Simlife101 this parameter, only indicates what is the lowest voltage threshold that the Low-voltage alert will be asserted. It's not setting the operating voltage. Even if you set it on 100v will still use 220v if you supply such. But in some cases for critical equipment that needs to work on certain voltage if the voltage drops can mean not enough power can be supplied from the mains outlet and should result in alarm to prevent damage in wiring from over currents. So, no, nothing like that parameter can contribute to issues you may have. Could have been just a bad batch of drives from the factory, in which case you could contact eracing-lab for replacement or advice.

[@tronicgr]

@@Simlife101 also, all these new white drives ship nowdays with pn83 set to 100, as they used in countries with either 110v or 220v mains, and has not been a problem.

[@luisbollosa2721]

PODRIAS MANDAR LOS PLANOS DEL 130ST-10025(220V) GRACIAS

[@tafsiruleko3277]

Sir, when key pad in parametee can, t fungtion, what trobel area check

[@EugenioCiullo_V-Blog]

work with PWM + DIR signals?

[@AhmedHussainEng]

how can I get Step and Direction so I can use it like the stepper with CNC controller?

[@skorkmaz]

Can you reverse direction with a pin in CN2 port?

[@ChrisdeJong-ADJ]

Hello i was checking all those parameters The first 3 servos were correct The last one was on Pn 09 not -300 but was set on -225, so i changed this amd press set, then i got the letters DONE and i got blinking dots... it looks it reprogrammed itself Now i have AL-13 overvoltage error ? Can anybody help me please ?

[@Mark_Blanes]

Thanks for the excellent video Thanos 👌 I just now discovered I have been running my 3 x PT Monsters at 5000 Rpm instead of 3000 (Pn51) for past 18 months. I was told that everything was set correctly at Shao's factory prior to shipping. Do you think it possible the higher Rpm setting will have caused degradation of the servo motor life or any other damage ?

[@tronicgr]

No, just causes snappier movements, perhaps a bit overshoot too on long runs if you don't have on the spike filter to slow down.

[@Mark_Blanes]

@@tronicgr Ok yes it was definately very snappy in the movements at 5000 !

[@truongkimson]

Hi, does the AASD fan make a lot of noise?

[@mehmetbaran3447]

Can we use any kind of servo motor with thanos board ? or does it have some requirements ?

[@ivantoshev3533]

Hallo,Thanos I am using the same servo motors for a 3 axis CNC router but I have problems with the user manual,have of it is in Chinese and I can't set the motors to work properly.Can you send me your user manual please.

[@sebastiensirois8915]

I'm checking my actuators with this and one is working but with the other three I get flashing dots at the bottom between each letter/number and the last line turns to an 'E' when I press the up/down arrows. --> I just asked this on your discord channel and well.

[@tronicgr]

What do you mean you are checking, what? The video just shows what parameters to enter to be plug a play with AMC-AASD15A controller...

[@sebastiensirois8915]

@@tronicgr Thanks, checking that the actuators were moving, got it figured out, Pn-083 voltage setting was wrong (deleted from your Discord).

[@rvb4972]

What is mean by Pn8 = 300 and Pn9 = -300, is these the length of the ballscrew

[@tronicgr]

No, these mean -300% and +300% max torque limits... above that for a few seconds the driver will stop with alarm

[@tronicgr]

You set the length of your leadscrew in the AMC-AASD15A LCD menu (stroke and leadscrew pitch)

[@carlfultz4379]

For the ASDA-A2 / B2 / M / S / A2 series, it is possible to use a programming software called Asda-Soft. Do you know if there is any programming software for the aasd-15a drivers?

[@tronicgr]

No sorry, I'm not aware of such software.

[@stefanwenn1804]

Did you find any software that suits for aasd-15a drives?

[@lexering1988]

Ciao, mi sapresti dire come fare il factory reset?

[@tronicgr]

Select Fn004, no need to enter a value. Just press/hold the Set button and it displays "Pni n", then press/hold Set again.. displays go... done... Remove power and plug back in.

[@lexering1988]

Mi da Err

[@lexering1988]

Fatto grazie mille

[@linhnguyen-vo8gu]

a have a servo drive code fault: AL-28 .i not see this fault in a document. u can help me that what fault?

[@tronicgr]

What it was doing when AL- 28 appeared? If not in manual I can't really say what's wrong

[@linhnguyen-vo8gu]

@@tronicgr It fault when runing.

[@nowwa]

hello Hello, my servo can be moved by hand and when I turn it back to the point. I need you to have more strength and not move. you know what parameter you have to adjust hola, mi servo se puede mover con la mano y cuando lo sueto vuelve al punto. necesito que tenga mas fuerza y no se mueva. usted sabe que parametro hay que ajustar gracias

[@tronicgr]

The rotation of the actuator by hand is normal for linear actuators. Some actuators that have floor contact use anti-rotation mechanism. See this video: kzbin.info/www/bejne/jJ7GlaKiatGArMk

[@keytools197]

Enable pn003

[@liliwarli5550]

How example with command triger ? Example video. .

[@liliwarli5550]

Ran triger ???

[@tronicgr]

Its activated from AMC-AASD15A servo controller automatically.