How to Replace CV Axle Shaft 2012-2022 Ford Focus

Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AAC...
This video shows you how to install a CV axle shaft on your 2012-2020 Ford Focus. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications. T
This process should be similar on the following vehicles:
2012 Ford Focus
2013 Ford Focus
2014 Ford Focus
2015 Ford Focus
2016 Ford Focus
2017 Ford Focus
2018 Ford Focus
Tools you will need:
• Phillips Head Screwdriver 1aau.to/oiY/1AX...
• Pry Bar 1aau.to/ocd/1AX...
• 13mm Wrench 1aau.to/oco/1AX...
• 1/2 Inch Impact Socket Set 1aau.to/oc/1AXA...
• 1/2 Inch Impact Socket Set 1aau.to/oc/1AXA...
• 13mm Socket 1aau.to/oiN/1AX...
• 18mm Socket 1aau.to/odQ/1AX...
• 19mm Socket 1aau.to/odQ/1AX...
• 32mm Socket 1aau.to/op/1AAS...
• Trim Tool Set 1aau.to/ocV/1AX...
• 1/2 Inch Air Impact Gun 1aau.to/oak/1AX...
• T55 Torx Socket
• Socket Driver
• Torque Wrench 1aau.to/ofA/1AX...
• Anti-Seize Grease
• Gloves 1aau.to/oaH/1AX...
• Safety Glasses 1aau.to/oat/1AX...
• Center Punch 1aau.to/o2/1AXA...
• Hammer 1aau.to/occ/1AX...
• Rubber Mallet 1aau.to/oK/1AXA...
Subscribe: / @trq
Check out our playlist:
Ford Focus 2012-2020 3rd Generation: • Ford Focus 2012-2020 3...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@calebwhitefilleul7959]

Can you post a front axel replacement for the FWD 2013 ford fusion? There's not a single video on KZbin for the 2013-2023 model fusions.

[@SkylerEnglund]

Dose this work for 2012 for fiesta se automatic

[@Harrell423]

I can't tell you how much I appreciate this video. Mostly for the sizes of the bolts. I had to drive an hour away to fix one of these in a foot of snow. Rescue mission was a success. Thank you so much. I didn't need anything else

[@rotisserieprotocol3582]

Doubt it's gonna go this smoothly for me but thanks a bunch for posting this!

[@elvis480]

Was your steering wheel stiff when you had cv axle problems ?

[@rotisserieprotocol3582]

@@elvis480 So my steering was stiff due to another issue I had at the time, but it was unrelated to the axle. It came from my ABS sensor. I hope that helps! *edit* Though it may come from those outer parts that connect to the tire, I know there's some joints in there and the rubber boots can slip off and the joints can start rusting. But don't take my word for it obviously. Just a thought.

[@elvis480]

@@rotisserieprotocol3582 yeah my steering has been stiff a little and whenever I turn left or right , my car makes a popping grinding noise so I think it’s my axles

[@SurrealKillcam]

never does

[@ThaSavageKayGamerTag]

​@elvis480, the popping sound is your CV joint, most likely, stiffness is probably got to to something with your steering fluid/ Steering fluid line.

[@dknot246]

If wanting to attempt this yourself, it is indeed easy. Only part that gave me trouble was the ball joint. It was catching on itself as it was trying to come out. Just had to move things around a little so it would fall out. Excellent video with all the info needed to complete the work. I did both sides in 2 hours. Fighting with that ball joint cost me 30 minutes. Also, be aware of the brake dust shield. If you bump it too much while working it may rub on the rotor after you finish the install. It will cause a metallic sound as you drive, just bend it back.

[@RicardoPCGamer]

I tried doing it on mine and i haaaaaaate the ball joint so much. I gave up on it.

[@dknot246]

​​@@RicardoPCGameryou can do it, just ask a friend for help. I needed an extra pair of hands on mine so I could move two pieces at once to line it up so it would slide out. Don't give up just yet. Lol. The passenger side was my problem side. The driver side came out perfectly

[@RicardoPCGamer]

@@dknot246 I learned the trick to get the Balljoint out. The Balljoint is at an angle. It will not come out pulling straight down. I gave it hell and nothing. If you grab the knuckle and push it in from the bottom. Then pull down on the control arm, the Balljoint will pop out easily.

[@dknot246]

@RicardoPCGamer Very nice! Hopefully this helps others in the future who want to try it themselves

[@richardparnell8402]

Thank you very much, I didn't think it would be this easy.

[@paddyrogers9289]

Great video very helpful really enjoyed 👍🤙from Ireland 🇮🇪

[@noahsmall2570]

Is this the same for the st focus?

[@SkylerEnglund]

Is this the same for 2012 Ford Fiesta SE automatic transmission

[@bluezhawg2104]

You do not need to remove that front splash shield. All the work required happens on the backside of the engine well away from the square shield.

[@kaptain3140]

Is there no axel shaft seal on the passenger side?

[@LoFi-Kingdom]

Title says for Ford focus. Does this include 2013 Ford Focus SE? Asking cause SE or other models aren't specified.

[@IRantweekly]

yes only real difference is engine power etc

[@royboy3597]

Well done

[@ANDY-we7mr]

I have a ford focus mk3 titanium x diesel automatic is this the same

[@NasrulFendi]

You dont need to refill the dct oil?

[@enriquegutierrez4754]

My vehicle slips always when im on complete stop and i accelerate replaced knuckle with bearings old were worn out thought it was the issue but it still slips.can that be due to a worn out shaft on the cv axle?

[@maxamillion4223]

Solid vid

[@ronthewelder7305]

How close is this to a 13 taurus?

[@HabeebAlasadi]

Thanks

[@ANDY-we7mr]

Did you take the drop link off

[@buckalvinpossumweight6252]

Why did you not apply anti seize grease to the end of the axle that presses into the transmission?

[@bluezhawg2104]

The inner is lubed by the differential oil splashing around.

[@buckalvinpossumweight6252]

@@bluezhawg2104 ah, ok. Thank you very much. I replaced the CV axle and the loaded steering knuckle myself yesterday although the only two issues that I had was the tie rod end the screw or bolt that is at the end of the tie rod with the boot it didn't quite go all the way up into the steering knuckle there's probably a half of an inch between the rubber grommet boot and the bottom of the steering knuckle. I hope that's okay. The other issue I had was the ball joint not quite fully being all the way inside it is basically all the way there but whenever I went to go put the bolt through you can see that there is a tiny sliver of the bottom portion of the ball joint sticking in the way and so therefore the bolt didn't quite go all the way through or I had to use the impact to pull the bolt all the way through. So is literally just a tiny sliver of the ball joint obstructing the boat from passing all the way through. And then I did have to bang on the tie rod a little bit to try to get it up in there and then I can tell my alignment is out a little bit although I will try to get it realigned tomorrow

[@elvis480]

@@buckalvinpossumweight6252 was your steering wheel stiff when you had your bad cv axle?

[@knockywigglesworth1909]

Why would anyone suggest to DIY without a lift to remove ball joint ? Rather just remove 2 strut bolts & done!

[@buckalvinpossumweight6252]

???

[@markcase913]

Yep lol that's what I did. My ST is actually just that one pinch bolt. Tbf my coilovers are slide out with no problem where as stock, rusty dampers need to reverse the bolt against a piece of metal so the knuckle expands and the dampers falls out.

[@buckalvinpossumweight6252]

@@markcase913 yeah, I definitely don't need a lift to replace my ball joint

[@markcase913]

@@buckalvinpossumweight6252 what? I agree you def, but removing the strut pinch bolt is imo still way easier. At least with my coilovers

[@dekunp]

Technically you’d need an alignment if you pull the strut out of the knuckle. Technically.

[@Batman-uy9ij]

I replaced it and when I drive, it makes an awful sound. What could be wrong?

[@cbar30]

6:42 LOL, you just blew the boot off your ball joint.

[@zachfriedman]

Is this the same for a focus ST with a manual?