How to Replace Front Wheel Bearings 2006-2012 Ford Fusion

Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ib/TKAX...
New Wheel Bearing Set from 1AAuto.com 1aau.to/ia/TKSH...
This video shows you how to install a new wheel bearing on your 2006-2012 Ford Fusion. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This repair was done on a 2007 Ford Fusion SEL 3.0L Sedan 4-Door AWD Automatic and the process should be similar on the following vehicles:
2006 Ford Fusion
2007 Ford Fusion
2008 Ford Fusion
2009 Ford Fusion
2010 Ford Fusion
2011 Ford Fusion
2012 Ford Fusion
Tools you will need:
• Pry Bar 1aau.to/o5M/1AX...
• 21mm wrench
• 15mm Socket 1aau.to/obXo/1A...
• 17mm Socket 1aau.to/obXo/1A...
• 19mm Socket
• 21mm Deep Socket
• 24mm Socket
• 32mm Socket 1aau.to/odS/1AA...
• 3 Jaw Gear Puller
• Ball Joint Press
• Brake Caliper Hanger 1aau.to/omw/1AX...
• Dead Blow Hammer
• Press
• Channel-Lock Pliers 1aau.to/oob/1AX...
• Locking Pliers 1aau.to/oob/1AX...
• Needle nose pliers 1aau.to/oHZ/1AX...
• Needle nose pliers 1aau.to/oHZ/1AX...
• Wire Cutters
• T40 Bit
• Ratchet 1aau.to/obZ6/1A...
• Socket Extensions 1aau.to/obXo/1A...
• Swivel
• Torque Wrench 1aau.to/oa4I/1A...
• Anti-Seize Grease
• Bearing Grease
• Gloves 1aau.to/oaQZ/1A...
• Rust Penetrant
• Safety Glasses
• sanding disc
• 10mm Hex Socket
• Floor Jack 1aau.to/oarv/1A...
• Jack Stands 1aau.to/oadH/1A...
• Large Hammer
• Pick 1aau.to/oYU/1AX...
• Punch
• Wheel Chocks
• Wire Brush 1aau.to/owY/1AX...
Subscribe: / @trq
Check out our playlist:
Ford Fusion 2006-2012 1st Generation: • Ford Fusion 2006-2012 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@blaingunter]

Yyyyyyeap. To the shop it goes.

[@DewFlew-wheel-center-caps]

Choosing a good wheel hub center cap can effectively protect the wheel hub and bearings, prevent daily pollution, and extend the life of the car wheel hub and bearings.

[@deetay450]

Yeah Ima head to the shop 😂😂😂

[@tg8150]

Easier to use a bearing/hub puller set rented from an auto shop and do this while it’s on the car. You WILL NOT be removing those lower control arm ball joints in your driveway I guarantee that. Using the rented tool and doing this with the spindle still on the car prevents the lower ball joints from needing to be removed.

[@cryangallegos]

No info on what tool was used to separate the bushing from the ball joint

[@aiden4961]

That rust is crazy lmao

[@cdb989]

Wow lot of dismantling for a wheel bearing