How to Replace Front Wheel Bearing and Hub 2008-2013 Nissan Rogue

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@bigguy4873]

Ive done both of my front wheel bearings now and this vid was a big help. As far as the backing plate, i dont care if it's a little rusty, they went back on, its mainly the outside edges of it thats rusty anyways. As far as the wheel sensor, dont expect it to come out without drilling it out with a 3/8 drill bit. Theyre only $20 on amazon so its a minor problem to resolve. Do yourself a favour and spray penetrating oil on all bolts to be removed a few times over a day or 2 to make life easier. I did it on the driveway, no hoist, and everything loosened up no prob. If the axle wont push in use a sledge hammer and have someone hold a block of wood, preferably hardwood, against the axle end and it will free it up. Ive saved over $600 doing it myself so thanks again for the tips TRQ! 👌

[@justinojimenez1018]

Excellent video.

[@dennycrane4261]

Sir, THANK YOU FOR THIS VIDEO!!!! Clear, easy to follow, direct to the point. You just saved me $300 in labor at the shop. 🙂

[@regio4327]

Are you from INDIA , how come did you put back on the same rusty backing plate.

[@CountyAuto]

@11:38 Notes: Axle nut torque: 188 lb. Ft/255 Nm.

[@ShampooAlgorithm]

Looks like that’s way too much torque, you might damage the bearing at that high torque. ProDemand calls for 92 ft-lb on the axle nut.

[@antoineward4475]

Lol you could’ve put a new backing plate on for them.😂

[@d.bansal3027]

How come you didn't get a new backing plate 😊

[@rafaelcruz8934]

Thank you for thi video, you did a great job

[@MiguelA.-yp5fp]

Thank you great job 👍 👏

[@kischillin5539]

How'd you get that speed sensor out so easy and smooth lol what is the trick to that?

[@salsacongressdjlexuz]

Very detailed explanation Thanks

[@erikchan9088]

Awesome. Thank you for sharing your knowledge. God bless you.

[@luiszelaya6299]

Why on earth did you put back that rotten rusty thing? (Awesome video)

[@TRQ]

+Luis Zelaya Thanks for the feedback! 1aau.to/m/Shop-TRQ

[@MariaVictoria-u1l]

This video was great explaining I will do this myself

[@redz_ninjaz]

Great video! thank you!

[@ShampooAlgorithm]

AXLE NUT TORQUE: 2008- 2011 92 ft-lb, 2012-2013 133 ft-lb, 2014-2021 188 ft-lb.

[@luisderivas6005]

You all know better than to use an impact wrench to tighten an axle nut, right?

[@Cesar-vk4pg]

Oh and also the caliper bolts have that much torque seems like a lot when the lug nuts are only 80 ft lbs last time I broke a caliper bolt over tightened it

[@Justadrifterhere]

Have a 2013 rogue and I tried this replacement. Those 4 bolts behind the hub are an absolute bitch. I tried everything, I shoved the axle as far as it would go, I turned the wheels a bunch of times to get a good angle, but still struggled so badly to get only 2 bolts out I said fuck it and sent it to a mechanic. I usually fix my own stuff with ease as I've been doing it for years, but this mechanic makes this look like a walk in the park. I get I'm not a mechanic, but this shouldn't be that difficult.

[@lithiumlounge6731]

Cut off the other tab? I’ve never heard of that

[@Cesar-vk4pg]

What if I re use the cotter pin Auto Zone said they didn’t carry them but then I look on line it says they do I guess the employee didn’t know what a cotter pin was 🤦🏻‍♂️🤣

[@betterwithcoffee8008]

2011 Rogue = It is NOT a 32mm nut on the axle. Going back to store now.........

[@nitobepantera]

日本語よりわかりやすい

[@mclovin_whiskey2695]

Ok

[@kakaa37]

Muy cochino este man aunque trabaja bien

[@adrianleeds3468]

Doesn't look roadworthy with that level of corrosion.

[@beboeltio1352]

Terrible job I would of call the customer to instal a new shield

[@JNYMOBILE]

wow.. you reused the rusty crusty heat shield??? why not leave it out!! dumb move

[@diongreenlee2286]

Almost over torqued that axle 😅