How to Install Leveling Kit 2009-2014 Ford F-150

Buy Now!
New Leveling Kit from 1AAuto.com trq.video/ib-1...
This video shows you how to install a leveling kit from TRQ on your 2009-2014 Ford F-150.
This repair was done on a 2009 Ford F-150 Lariat 5.4L Crew Cab Pickup 4-Door 4WD Automatic and the process should be similar on the following vehicles:
2009 Ford F-150
2010 Ford F-150
2011 Ford F-150
2012 Ford F-150
2013 Ford F-150
2014 Ford F-150
Tools you will need:
• Pry Bar trq.video/oTe-...
• 10mm Socket trq.video/oa9J...
• 13mm Socket trq.video/obtw...
• 15mm Deep Socket www.1aauto.com...
• 15mm Socket trq.video/obtw...
• 18mm Socket
• 21mm Socket
• 27mm socket trq.video/oT-1...
• 30mm Socket
• Trim Tool Set trq.video/oaaH...
• Locking Pliers trq.video/okC-...
• Torque Wrench trq.video/oaDM...
• Bungee Cord
• Copper Anti-Seize
• Gloves trq.video/o49-...
• Safety Glasses
• 8mm Allen Wrench
• Floor Jack trq.video/o4Q-...
• Hammer
• Pole Jack
• Vise
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Ford F150 2009-2014 12th Gen: • Ford F150 2009-2014 12...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@gettendeep18]

Glad to see this done on what looks like a northern vehicle exposed to some salt. A lot of other videos always show nice clean components

[@josephkrehel9813]

I put the Allen bolts in from the other side. Then you have studs like the original.

[@marcus5686]

Thought this was something I could do myself 😂

[@razorblade-serenade-ic9my]

This is why I pay people to put leveling kits on my trucks and gladly so. Its worth me giving them my money because it really is a big hassle if you try and do it yourself and you can do more damage than good if you dont know what youre doing. You can wreck your 4 wheel drive for example if you dont have the right tools and knowledge just trying to install a leveling kit. And as you can see it looks like he put knew struts and shocks on and that is the way to go if youre putting on a leveling kit on an older truck.....might as well replace them while they have all the parts disassembled to do so.

[@iap6647]

Great video! Thanks for posting this.

[@Hawks405]

So I was attempting to install a leveling kit but my suspension was all out of wack. Once I put it all together my upper control arm was touching the springs on the struts. It looked like the sway bar links were too long and not allowing the suspension to lift up to the proper height? Or if I am just Special and should never touch a wrench again😂

[@tuckessee]

Get ready to replace CV constantly... the control arms get put at such an awkward angle with this, I'm about to put my 3rd cv on the driver side this year. When I do that I'm removing the leveling kit

[@Foxyy.Red93]

I really thought you ran the bolts through and flipped it over and ran the nuts down in the factory studs and had new studs with nuts going through the top.. I have never seen it like this

[@tanfer2003]

Great video except you didnt show the end look

[@theking-bh9ph]

So you need to get new sho

[@RonnieYoung-zx8wu]

Who puts a level in kit used strut

[@arizonaf2503]

I'd replace upper control arms while I'm in there.

[@andrewhurley2379]

Why does everyone do this the hard way? Just remove the lca bolts !

[@Brewsquadtv]

Anyone else blew on the phone when he hit the bolt through? 😅

[@timulm1221]

The fact that you didn't explain how the strut needs to be rotated 180 degrees to line up the top mounting bolts. I hate I when these videos seen to easy. There's always something unsaid.