How to Replace Front Wheel Bearing 2011-2016 Hyundai Elantra

Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ia/TKAX...
This video shows you how to install a front wheel hub on your 2011-2016 Hyundai Elantra. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2011 Hyundai Elantra
2012 Hyundai Elantra
2013 Hyundai Elantra
2014 Hyundai Elantra
2015 Hyundai Elantra
2016 Hyundai Elantra
Tools you will need:
• Flat Blade Screwdriver 1aau.to/of/1AXA...
• Impact Screwdriver 1aau.to/oa/1AXA...
• Phillips Bit in a Ratchet 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/of/1AXA...
• 17mm Wrench 1aau.to/od/1AXA...
• 10mm Socket 1aau.to/oe/1AXA...
• 12mm Socket 1aau.to/om/1AXA...
• 17mm Socket 1aau.to/om/1AXA...
• 19mm Socket 1aau.to/oh/1AXA...
• 21mm Socket 1aau.to/oh/1AXA...
• 30mm Socket
• 32mm Socket 1aau.to/ob/1AAS...
• Acetylene torch
• Brake Caliper Hanger 1aau.to/oc/1AXA...
• Press
• Needle nose pliers 1aau.to/oa/1AXA...
• Needle nose pliers 1aau.to/oa/1AXA...
• Snap Ring Pliers
• 1/2 Inch Air Impact Gun 1aau.to/of/1AXA...
• Air Chisel 1aau.to/oa/1AXA...
• Socket Extensions 1aau.to/om/1AXA...
• Swivel
• Torque Wrench 1aau.to/oj/1AXA...
• Copper Anti-Seize
• Liquid Thread Locker
• Rust Penetrant
• sanding disc
• Sandpaper
• Brass Punch
• Floor Jack 1aau.to/of/1AXA...
• Hammer 1aau.to/od/1AXA...
• Jack Stands 1aau.to/of/1AXA...
• Large Hammer 1aau.to/od/1AXA...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@Olds_Pwr]

I don't know if there is an advantage over a press in bearing over a bolt in hub bearing. But, I do know a bolt in is so much easier to replace.

[@5dayslater]

Welp, looked up this job to do it myself as an amateur and decided I will not be performing this job. Lol but major props to the mechanics where this is a no-brainer job!

[@cromags1120]

Nice video! I would just buy another knuckle and call it a day.

[@idalbertoross298]

Que bien trabajan ustedes y lo explican todo a la perfección , bendiciones para todos

[@marks5625]

Thanks for all your videos. Thank you for explaining thoroughly. I learn alot from you. Thanks for being you

[@capitaldd3693]

Great walk through with explanations.... thanks for posting 👍

[@GMZee559]

Great Video Torque Specs and everything Very Professional ‼️‼️

[@danielcortez6708]

Really appreciate the video! Very detailed!! Thank you!

[@csf3939]

If I reuse the old hub, can I leave the race on it or do I have to take it off? Wherever I looked to order bearings they don’t seem to come along with a new race…can someone explain please? Thank you

[@mcscheck2000]

In the age of bolt on wheel hubs Hyundai is still using press-fit??

[@axelG777]

On 11:46 if I replace my whole hub/spindle I don’t need to take off the old race and install it on the new one correct?? For my new hub it would be without a race?

[@darthwatto]

Ya that race is from the old bearing, he needed to remove it order to reuse the original hub. So if youre replacing your hub you dont need to transfer it or anything.

[@dukboat2886]

Hey man I got a question do you think this is the cause for my front drivers wheel squeaking everytime I make a right turn?

[@StormWalker101]

Is this the same person from 1A auto parts channel? Because they sound exactly the same.

[@tomalophicon]

Great guide thanks

[@michaelgutierrez6564]

@12:21 you didn't get the race hot enough. Spin the hub as if you were spinning a bicycle tire while holding the torch steady. The race will expand enough and fall right out.

[@ruslangulyak]

❤ thanks

[@aaronmartz.1464]

no grease?

[@seanpinson9030]

These people must live in a total rustbelt I just did mine and it doesn't look all white and salty underneath

[@richitrx7]

do you have to grease TRQ bearings?

[@JP-zg5jy]

Thanks!

[@josefranciscoesquertalaman3827]

Like

[@ThreeWheelJr]

You forgot to show how you got the hub out

[@osiris1plus]

Great video! I was surprised to see how much original equipment was still useable.

[@jfiore07]

I mean, a replacement hub is pretty reasonably priced

[@JP-zg5jy]

Thank you for taking the time to make this video you did a excellent job explaining everything. I appreciate u

[@jmanyea08]

13:05 so you took off the old race and did not put a new one?? is that common practive?

[@richitrx7]

...ugh what happens if you mess up and the new bearing becomes undone during the new bearing installation but can still put it back together lol

[@lalabilloo]

Very good video ❤ Thanks,

[@moparnut6933]

I wish you would have gone more in depth on how you mounted the knuckle on the press.

[@jesseowens1492]

Bravo on the antiseize!

[@giftedpeace0]

Thank you

[@infamousdjnoxzeit1250]

would there have to be any preload on those components(bearings/ race) or just bottom them out?

[@wut2dew]

So I have to do about 50% of all of this just to get my broken wheel studs off?!

[@tomalophicon]

Replace the bearing while you're there.

[@seanpinson9030]

Watching this video makes me so glad I rinse the bottom of my alontra every winner about once a week And I'm not spelling things wrong I'm talk texting