How to Replace Intake Gaskets 2003-2007 Nissan Murano

Buy Now!
New Intake Manifold Gasket Set from 1AAuto.com 1aau.to/ia/1AEG...
Gaskets help seal joints between components in places where you don’t want air, or fluids leaking out of that seal. Rubber or silicone gaskets may dry out or harden over time, reducing their effectiveness. This video shows you how to install new intake manifold gaskets in your 2003-2007 Nissan Murano.
This process should be similar on the following vehicles:
2003 Nissan Murano
2004 Nissan Murano
2005 Nissan Murano
2006 Nissan Murano
2007 Nissan Murano
Tools you will need:
• 10mm Socket 1aau.to/of/1AXA...
• 12mm Socket 1aau.to/oe/1AXA...
• Ratchet 1aau.to/of/1AXA...
• Socket Extensions 1aau.to/oe/1AXA...
• Cloth Rags 1aau.to/oa/1AXS...
• 5mm Hex Socket
• Razor Blade / Gasket Scraper 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Nissan Murano 2003-2007 1st Generation: • Nissan Murano 2003-200...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@annekruse4389]

Love the precision torque wrench you used. I've never seen that before. And I didn't know there was a sequence for tightening bolts. My mobile mechanic apparently didn't change the gasket, or perhaps didn't have a precision torque wrench, when he replaced my sparkplugs and my new mech said there's an oil leak coming from this area. I'm not doing it myself, but wanted to see what it involves. Really great delivery of information and teaching method.

[@TRQ]

+@annekruse4389 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

[@henryvalentine4203]

Lucky you! You seemed to have no trouble at all removing those two 12 mm hex head rear bracket bolts. I had a very hard time of it! I was afraid I would round out the heads with my 3/8" drive 12-point socket so I bought a 6-pointer. I could not get enough leverage on the closest bolt but I was able to get the other with the socket handle sticking almost straight up. Next plan was to get a shallow 6-point 1/2" drive socket which I did. With that and the larger handled 1/2" drive ratchet I was finally able to put enough foot pounds on it to break it loose. It was very difficult however as there is not much wiggle room in that area. And you did it with a 1/4" drive ratchet? Amazing!

[@nATHAN-rk9hf]

There are 2 wire brackets on the back of the intake that arent shown in any video ive seen. I thought one has a hose but it was connector cable held by a bracket. Then there is another holding that tinfoil cable. Maybe you dont need to screw em back on but it was tough getting them off... Tomorrow we'll decide. Wish i knew before, would have saved me a hr... :(

[@hamody55at]

Hi, in min 5 you are removing clamp of a hose. Ik the other is connected to the pvc valve but the one you are removing exactly in min 5. What is that hose for.

[@rodger6940]

Bro what would you do if you drop a the nut in the cylinder 6 it fkn happen to me I don't no what to do

[@faulksportsentertainmenttv2959]

Great 📹

[@drummin2dabeat]

where did you get those pliers? i want a set of those.

[@demondharris1273]

Legend. Just legend, thank you 👍🏾

[@nicanightmare23]

The best!! Just what I needed my friend!!🚗🫶🏽