TRUCK NORRIS cam before and after 5.3l with 3" cutout

[@jordanturner9173]

THAT is definitely a GMT800 with a threatening aura😉

[@littleblue7838]

Facebook buddy hello:)

[@eliforbes4842]

as well😂

[@SteelebillyWes]

HOSS

[@ryanlagoda1352]

"but for now I gotta get my groceries inside" 😂 and just like that life came back lmao

[@eliforbes4842]

good thing i found this on my recommended! been wanting to swap that cam in my truck for a while but now i think im really gonna

[@carter4627]

Keep the stock converter. Nothing wrong with it. Its still good for towing and 725 is a decent idle and good for daily driving. Just plan to upgrade your trans and get a converter at the same time, not saying you make too much power for stock trans. Just a built trans it so nice and will lower 0-60 and 1-4 miles alot

[@dragracemase]

It has a built trans already when I bought it I ended up getting a fti 2800 stall and it drives 10 times better and can still tow a car like a stock converter. It made 340hp on the dyno

[@briankinzer4175]

@@dragracemaseidk if you asked the tuner or not but can it make more than 340? It was that about it without head work being done

[@dragracemase]

​@briankinzer4175 you can make more with e85. Everyone's dyno is different I could make a pull on someone else dyno and see 300hp they will all give a different number

[@christophvest]

sounds great!

[@kingsupra5023]

Hello, Does BTR 5.3 HOT ROD CAMSHAFT fit yukon 5.3 2008? I am add long tube headers and Y-PIPE and full exhaust system 3 inch Cold air intake DOD DELETED Yukon 5.3 2008 has 4L60E transmission should I upgrade the converter to FTI STREET BRAWLER 3200 STALL SPEED Thanks a lot Thanks,

[@dragracemase]

I would recommend a converter I tried to get away with the stock one driveability wasn't that good

[@hammer7226]

How did you get the muffler to open and close with a remote

[@gearhead7896]

Hey bud, sounds great. Try DynoMax (Walker) mufflers next time. They outflow Flowmaster. Quick question; how is the vacuum for the power brakes?

[@dragracemase]

Was looking for a quiet muffler I do alot of highway driving. The brakes are there lol definitely can't be scared to get on them hard.

[@kendalackron3093]

I had mine straight piped but my dad made me put a muffler on there I miss it everyday.

[@dragracemase]

Get an exhaust cutout. Best of both worlds

[@kendalackron3093]

@@dragracemase thats a great idea thanks

[@jonathanfaatuai8178]

Hey how do you have the edge tuner hooked up and what model is that I want to install one in my truck as well thank you !

[@dragracemase]

It's a cts3 it plugs into your obd2 port super simple

[@adinagabriel1431]

Where is truck Norris now

[@dragracemase]

Getting new 2 piece drive shaft installed 👌

[@elianaramirez4051]

🕵‍♂️

[@ANTIStraussian]

If jesus came back he would drive this 😂

[@chris09mejia1]

Sounds great man. What did you set your idle at?

[@dragracemase]

725rpm once I get a converter I cam lower it down a bit

[@chris09mejia1]

@@dragracemase just did my 5.3 with this cam. Sounds good

[@chris09mejia1]

@DragRaceMase mine sounds too stupid loud now tho 😒 I gotta reevaluate the exhaust

[@dragracemase]

@@chris09mejia1 cut out is the way to go with a good quiet muffler. Best of both worlds

[@DJsConstrictors]

Where in Michigan are you? I’m in Westland I want to start a 5.3 build for my 98 really soon

[@dragracemase]

Southwest MI

[@tonnaantoniordz8090]

What is the name of the screen that checks the revolutions and all that, or where can I get it?

[@dragracemase]

Cts3

[@yuugi925]

What drop kit is on it and how does it ride?

[@jonathongrier9661]

How is it after tune?

[@brianperez4164]

What cam specs you get the parts number if you don’t mind me asking

[@mr.3phase228]

212°/22x° @.50 107.5 LSA. Avaliable in either .552 or .498 lift. .498 can be used with stock springs.

[@luisdominguez7154]

what’s the drop on the truck?

[@dragracemase]

4/8 with air shocks in the rear to have more adjustment

[@michianaracingchannel412]

Wow

[@shawncole7536]

Maaan that truck sounds good, bathroom break!!!!🙄

[@dragracemase]

Lol thank you she's been on jackstands I broke the driveshaft waiting for my 2 piece to show up then I'll make another video of driving it with stock converter and some draggy times

[@kolinhaithcox7361]

🎉

[@ale-gs8xq]

Get a 2800 stall with some 4:10 gears

[@dragracemase]

2800 stall and bigger trans cooler coming next

[@jeffnunley1861]

What rpm does it idle at

[@dragracemase]

725 with stock converter

[@jacquie6141]

💃 Promo-SM

[@andrewbowles923]

Grocery getter

[@dragracemase]

Low and slow.

[@xxyvng6831]

faster than ur shitboxes tho

[@williamlopez4934]

Get a 3,200 -3,500. Anything under 3,200 is a waste of time and money

[@dragracemase]

I was thinking a lower stall cause I'm going to be towing a car trailer alot maybe 2800?

[@williamlopez4934]

@@dragracemase 10 inch 3,200 be cool . thrd gear locks up. So u won't be stalling all the time.

[@angelcastillo2399]

what led bulbs did you use

[@dragracemase]

Amazon cheap ones lol bright asl