How to change brakes on semi truck Frightliner Cascadia, kenworth volvo

[@D3vinePurp0se]

Bro you're out here turning me into a full blown truck mechanic lol

[@TRUCKINGTIPSDIY]

Nice! Hopefully it will help you on the road, thanks for watching sir 🙏

[@bladimirb4526]

Sameee 😂😂 comienzo mañana

[@Jreddygo]

😂😆👍🏽

[@JC-cc7zu]

Put anti seize on those anchor pins, helps the next guy out 😁

[@angelozararis8096]

A must I always use it

[@michaelnoonanjr6574]

I watched several vids on break jobs. Yours was by far the best

[@TRUCKINGTIPSDIY]

Thank you, really appreciate it 🙏

[@Cantante1963]

My kind of video. No nonsense and straight to the point. Gracias.

[@michaelwolflake4918]

Assembly of the shoes is very satisfying.

[@rickykingi5191]

I’m gonna do my own front brakes on my truck.. hopefully it goes well. Thanks for sharing brother 🤙

[@koollee]

Damn!! Thanks yo. Im an outdated automechanic and truck driver. This is easier than car brakes.. just bigger and heavier. I will say 1 thing tho. Brake on a Mercedes benz (i had a big S class) were prolly the easiest in the world lol

[@SOPHIAFLYGIRL]

I have a 1979 Mercedes 300D sedan, the brakes are 2 small cards, 2 pins, slide out, put new ones in, replace pins, dunzo!!

[@grisdale2007]

Keep making them videos, future owner op here. Planning to buy my first truck..

[@andrewmccaskill2845]

the up close shots and using the names of the parts and tool reccomendations really help and set this channel apart from most others

[@jayman6860]

Reminds me of the times i had to do brake drums all day. Thanks for refreshing my memory on this. Keep up the great videos 👍

[@garcestransportgarces4090]

No le seque mi chingon! Saque Los bushings! Es una Chinga! Los Los cambie! Ya me and abandoned! Jajaja

[@truckdriver4323]

Thank you for such a helpful video. Short and easy to watch

[@kingkon164]

It's that easy 🤯 A car rear drums is more difficult then that..

[@TRUCKINGTIPSDIY]

Yes its easy, hopefully its helps you, thanks for watching sir 🙏

[@Phoenix1008]

Thanks for this video...you're an excellent truck mechanic. You did a great job👍👍

[@Holdspeare]

Some anti seize lube works great to not have to heat up to cut anything out. But not everyone used

[@gregoriomartinez6670]

EXCELLENT,. PERFECT GOOD JOB PRIMO.

[@jaimealvarez3009]

CHULADA DE VIDEO BIEN EXPLICADO Y CON LA CAMARA TAMVIEN VIEN GRAVADO ANIMO! Y saludos desde portland oregon

[@TRUCKINGTIPSDIY]

Muchas gracias, saludos amigo!!!

[@dayanagronesbelt9707]

those shoes looks in good conditions

[@roadhouse72able]

New sub,Thank you for the video very helpful and perfect for the O/O

[@TRUCKINGTIPSDIY]

Thank you i appreciate it 🙏

[@derobertjames2083]

Great video. You got yourself a new sub!

[@noelamezquita5868]

The 2 dislikes are the people who own shops😂

[@TRUCKINGTIPSDIY]

😆 lol

[@moneymikeslickwill8749]

Another great video brother

[@carloss9360]

This video was so informative great video thanks

[@rodney31907]

Very Detailed video. Thanks much!

[@TRUCKINGTIPSDIY]

Thanks for watching sir 🙏

[@JT-qf4it]

What was the problem with the used shoes? They looked as good as the new ones.

[@anumnakiperez7124]

Esta perrona esa explicasion primo 👍👍👍

[@manpreetsingh-lh1km]

Hi brother thank you for sharing your experience and wisdom appreciated. Can I please know what is that adapter called for air gun when you pushed out barrel ?

[@quocbinhduongnt8646]

thanks anh nhiều vì clip này hay lắm anh ơi

[@jorgerodriguez6470]

Thank you ☺️.. Good Video!!

[@hectorperez-zq3uc]

Man watching you mushroom the anchor pin before heating them was killing me and having you check s cam play with the brake chamber applied was another and the mack book recommends putting the shoe on the anchor pin first and using the tool to put the roller pin spring on

[@govinlama6152]

❤❤❤ always great videos 😢😢😢❤❤❤❤

[@nicolesmrekar2046]

Hollowed ended press, 10 seconds you can press them out. I did it today. lol

[@temesghenghidey]

Yo it’s just easy way I like it easy and quick 💯

[@johnysilver1853]

Very useful video. Thank you!

[@tfltrucking9156]

Were those brakes still good that you replaced?

[@bosleylogisticsllc8244]

What size brakes pads for 2016 or part number for steers and drives please?

[@SergioGarcia-mh4ko]

Great video 👍👍👍👍

[@williammiguel2521]

You make look too easy 😅but good video thank you.

[@Xetai18banh]

It’s ok change new brake shoes, but use old brushing ?

[@kelwincartagena9928]

Exelente canal

[@TRUCKINGTIPSDIY]

Michas gracias!!

[@moose2577]

Well damn. That does look like an easier way...

[@g41thomas]

Great video ....thank you

[@TRUCKINGTIPSDIY]

thank you!!

[@yayaicey24]

Good job👍

[@TRUCKINGTIPSDIY]

thank you sir!!!

[@shatteredsquare]

"now we're gonna call an air strike on this pin, cause it didn't want to come out"

[@dvaladez5628]

What is that adapter you using on the air hammer ?

[@helderhenoch3698]

Boa noite daqui de Portugal gostei do seu vídeo parabéns muito profissional obrigado Hélder Henoch

[@evanalhashimi426]

how long do u think or estimate time should be change again?

[@IronHorseHD]

They make a tool that goes on the air hammer that knocks them bushings out.

[@mannyh1164]

can you share the year of your truck and what shoes and drum number you used I have to change mines and need to know what to buy! thanks

[@thecollector3402]

I gonna use the vase grip now

[@angelsantana2739]

Great video

[@TRUCKINGTIPSDIY]

Thanks for watching sir 🙏

[@alfonsohernandez8793]

Thank you so much 👌👍👍👍👍

[@jodyodette8907]

How often do u change the drums?

[@Embermist69]

Personally I feel every time the shoes are replaced. Usually they both worn together, so why not start fresh. If one wants to reuse, check the inside specifications of the minimum when considered out of specifications.

[@СтепанБандера-ы8у]

What was the mileage on this truck and how long does your lining last?

[@xanatgarcia9241]

As a heavy duty tech, I’ve seen them last for 1-3 years but it all depends on the driver and how heavy they load

[@danielserrano591]

kit set ,cylinder ,band

[@falcon9282]

Awsome video

[@MrDebrafe98]

Where can I buy that air hammer?

[@sahibradiousa1201]

Nice 👍

[@nathanharrison816]

Never seen an air hammer before that was cool As fuk.

[@Lifeisaquicktrip]

Thank Bro. 🙏🤓

[@andrewl2962]

Good job !!!

[@RichardHampande]

This is impressive

[@jorgefacio690]

shouldn't you replace the drum also?

[@TRUCKINGTIPSDIY]

hello, it is better if you replace drum and brake shoes, but if the drums are still good you can reuse them, if they're not warped or too worn out

[@noelvillafane7747]

just subscribe bro great content DIOS t bendiga hermano palante gracias thanks

[@lilic724]

I put my truck in shop yesterday to replace steer brakes and drums , after I get my truck and take it on the road I noticed my truck is shaking around 50to70 mph , I m not sure what it is but It was smooth before the brake job, could it be a bad drums

[@lawsondj1244]

Check your radial runout on your front tires...sounds like those are out of round. everytime you pull front tires off, you have to make sure they are within spec as far as radial runout goes...

[@ghundhudzakpamiri161]

Thank you !

[@JcFortin]

Where i am from some time we have to break them in half because de to sease

[@stevenbaker673]

Good job thair fellers

[@merlonfox8769]

What about the trailer? I have a pup that’s been squealing

[@quocbinhduongnt8646]

6:13 là ok

[@MG-ks1qg]

It's usually a good move to just cage the chamber instead of messing with the slack adjuster

[@shawnevans9106]

Why? Supplying air to the chamber would do the same. There are only two reasons to cage the brake chamber. 1. To allow a truck with a failed chamber to make it back to a shop. 2. To install a piggy back. You will still have to adjust the slack adjuster once you install new brakes anyways.

[@moose2577]

It takes 10 seconds to back off the slack adjuster...

[@DavidStapley0982]

Sometimes you gotta do both. On badly scored drums that's the only way to get it off.

[@franciscogonzalez9953]

Sale con esta clase ya le puedo cambiar las brakes a mi Silverado 🤔

[@eriksatterfield4755]

How can I remove the pin i put it on the wrong side?

[@TRUCKINGTIPSDIY]

Just hit it with a hamer, pin wont bend

[@eriksatterfield4755]

@@TRUCKINGTIPSDIY thanks I eventually figured that out thank you

[@moisescamacho4181]

por que no asen videos en español seria muy bueno si pudieran

[@TRUCKINGTIPSDIY]

tengo unos en español, voy a tratar de haser mas, gracias!!

[@danielserrano591]

hammer

[@bigdaddywillerson6905]

What shoes are you using 4707 or 4709

[@nathanpetrohilos]

They look like 4707 shoes. 4709 has a different style roller pin spri g i believe

[@tajindersingh3506]

Yea they r 4707 cuz they have red lining nd 4709 have blue lining

[@billhurd9055]

Thanks for the info

[@TRUCKINGTIPSDIY]

Thank you for watching sir appreciate it 🙏

[@sanelyarelo7005]

Te felicito por tu canal auque no domino el inglés me gustaria que en esta video midieras las toletancia del tambor y el torque que llevan las tuercas de los birlos espo no incomodarte con mi comentario

[@TRUCKINGTIPSDIY]

gracias por tu comentario, saludos!!

[@alphatruckersinc.9417]

Great one, thank you. Do u know how much gap should be between break shoes and the drum?

[@TRUCKINGTIPSDIY]

hello, im not exactly sure, some adjusters require half a turn others 1/4 turn (counter clock)

[@alphatruckersinc.9417]

Thank you

[@painkey1189]

It depends on what dot enforces and how big the hills are

[@lve5571]

Hey man thanks.

[@otisrhooms7426]

Good job

[@TRUCKINGTIPSDIY]

Thank you sir!!

[@eliasrm96]

Thanks bro

[@moctezumaRevenge]

Do the other style of brakes mine are different same idea though

[@TRUCKINGTIPSDIY]

What kind do you have?

[@moctezumaRevenge]

@@TRUCKINGTIPSDIY I have no clue what they are called the difference to me is the spring instead of the side like you showed they go on the ends not sure if it’s a older style.

[@jonathanmoore4903]

Why did u have to grind it?

[@TRUCKINGTIPSDIY]

Hello, you can see in 5:31 that the roller got got wider when we hammered it, so we just grinned the edges for the roller to come out easier, (that juslt in case the rollers dont come off easy, thanks for watching!!

[@jonathanmoore4903]

Ok is that faster then using anchor pin remover?

[@jameswilson3979]

Anchor pin press is easier and you can change bushings with them also

[@ibrahimnaser7142]

Thank you , great job!

[@TRUCKINGTIPSDIY]

thank you sir

[@silverload3622]

And never seize the shit out of all pivot points

[@d-s-ll2378]

best way!

[@kulwant747]

Thanks

[@elloko8303]

Viva México great vid

[@TRUCKINGTIPSDIY]

Gracias amigo 🙏

[@saidibrarkhan5566]

Good sir

[@Boyleheights213por-vida]

What year was the truck you worked on little buddy???

[@TRUCKINGTIPSDIY]

Its a 2013

[@ilvintirado5605]

Job it’s not complete it’s the brake box bring bushings and rollers you have to change everything !!!

[@TRUCKINGTIPSDIY]

I explained that in the video

[@smittyfewbad1072]

Whats the part # oh those brake and drum

[@TRUCKINGTIPSDIY]

Im not sure, but at the deer with the vin they'll be able to look for it, thanks for watching sir 🙏

[@СтепанБандера-ы8у]

I think he got wide 4711 shoes and meritor special drums and I think drums are very expensive

[@bekuz2970]

Thank you excellent video.

[@TRUCKINGTIPSDIY]

thank you sir!!

[@josereyes7111]

👍👍💪

[@lekseipato2242]

Судя по накладкам барабанам кирдык! Или 2 ремонт накладок надо

[@shdadedam7355]

Bro you need to put new drums every time you replace the brake shoe !!!

[@TRUCKINGTIPSDIY]

Not really!! But its always better to do

[@alpham777]

Nah only if they are cracked or grooved out to bad. We usually run them 2 sets pads per drum but sometimes have to change them even after the first set. There are specs for all of this tools to measure it.

[@official_g6106]

1:15 hits drum but says “don’t hit metal”

[@moose2577]

Middle

[@danielserrano591]

foot brake ,pedal clucth ,clucth ,brake,cylider ,band ,asbesto ,brake ,front,new ,unhood

[@danielserrano591]

no spring