How to install LED Flasher Relay on a 2003-2006 CBR 600 RR by TST Industries

Our amazing Adjustable LED Flasher Relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated taillight. For more info see: tstindustries.com/03-06-600RR-...
Make sure to subscribe here: bit.ly/1jq2ZrN
Follow us on Facebook here: on. 1nuTjlF
Follow us on Instagram here: / tstindustries
Follow us on Twitter here: / tstindustries
If your signal lights flash too fast (hyperflash) this part is your solution!! It is very easy to install and does not require any special tools...it plugs right into the harness. This component works with the following signal configurations: 1. All stock 2. Stock taillight, aftermarket signals 3. Integrated taillight, stock signals 4. Integrated taillight, aftermarket signals. We designed this part to fit right into the crimps on harness wires of your bike so the installation is a snap! This trick relay also enables you to also adjust the flash rate of the signal blinking with ease.

[@600rrcbr7]

You guys made putting my flushmounts and intergrated light in so easy. Got the relay dropped in yesterday and the signals/brake light work perfect. Super bright. Your company is one of a kind. Not a lot of companies work as hands on as you do with their customers. I needed help and messaged you guys on Facebook and had a real-time conversation with someone. Helped me out a ton. You guys are the best at what you do. Thanks

[@TSTindustries]

Thank you for the kind words. Our main objective is to help our customers enhance their experience with their bike. I think we were pretty successful at accomplishing that with you.

[@YourStepDadBob]

So just this one relay takes care of flashing related issues around all 4 led’s being the integrated tail/and flush mount led front blinkers as well?

[@TSTindustries]

@@YourStepDadBob yes...one relay controls of all the signaling lights on the bike.

[@letstalk9037]

This by far has been the best video in regards to ease due to instruction. I am a Army Veteran and have gotten into Go Karts as a hobby. I needed installation help with a flasher relay and this has helped more than I thought. Great work and God speed. I will subscribe and like.

[@TSTindustries]

Good to hear it man. Thank you for your service and appreciate the feedback!

[@EnjoyCalculus]

Bought this and installed on my 04. Works good so far. Didn't bother changing the relay interval timing. Was a bit hard to remove the wires from the blue plug but it was a fairly easy installation. The relay is a bit more expensive than standard relays but has a much easier installation.

[@blissmogu]

Hey man can you tell me where the relay is placed on your 04'?

[@smuir44]

Finally fixed! Easy install and the signals are back!

[@TSTindustries]

Awesome.

[@trainOG]

I have this switch on my bike 2006 cbr600rr full carbonfiber I have led turn signals and integrated taillight took me about 5-10 mins to install and remove those crappy resistors that get hot and wide this bad boy up also took the time to adjust the blinker settings which is fine out of the box but so dope you can adjust it if you want too but back just wanted to say if you are even thinking about buying this or. Resistors buy the tst switch and save your self from more wires to tuck and melted fairings this relay switch is superior in every way A+++++ thanks tst for the badass product will be back for other items soon

[@TSTindustries]

Thank you for sharing that with us. I am so glad that our parts made your installation better and easier. This is what we strive for.

[@martins.8713]

Thank you! Good work!

[@romika5450]

Thank you so much for this video. This took me a max. of 10 minutes to install!

[@TSTindustries]

Great to hear!

[@maxfrimming3644]

Habe lange nach einer Lösung gesucht. Das hat mir geholfen! TOP

[@TSTindustries]

Groß!

[@kobeeejay]

Thank you very much for all the informative tutorials you have on this channel! 👍🏻

[@camiloallen174]

i know im asking randomly but does anybody know a tool to get back into an instagram account?? I was dumb forgot my password. I appreciate any help you can give me!

[@hendrixroger5059]

@Camilo Allen Instablaster ;)

[@camiloallen174]

@Hendrix Roger i really appreciate your reply. I got to the site thru google and I'm trying it out now. Takes a while so I will reply here later with my results.

[@camiloallen174]

@Hendrix Roger it worked and I finally got access to my account again. Im so happy:D Thanks so much, you saved my ass :D

[@hendrixroger5059]

@Camilo Allen happy to help =)

[@Ivan-ui1vk]

Thank you ! Super helpful.... works perfect

[@TSTindustries]

Great to hear! You are welcome.

[@fb376759]

Currently my fairing signal lights are flashing opposite of the tail. Is this a problem that could be fixed by this relay or rather a wiring issue? Just got the bike working out kinks

[@redrocketat615]

I have an 06 cbr600rr I just bought that has the same LED lights, but rather then flashing rapidly they’re not blinking at all and just stay on, will this solve that problem as well? Thanks

[@advntrgirl883]

What a great video!!!!! thanks for the easy instructions. Thank you!!!! On my way to fix it.

[@TSTindustries]

you're welcome. We are glad to help.

[@darksorceresszyra9467]

Thanks TST. I just got the same relay for the 954RR. I realize that the harness is identical to this one with the same colored wires and placement in the connector. I bought the 2003-2006 relay with the white clip as well. When I install the relay, I will give an update.

[@TSTindustries]

We are looking forward to hearing your findings.

[@darksorceresszyra9467]

Ja. Thanks for having awesome products that make it easier and more reliable to modify than using load resistors or cutting into the motorcycle side wires. I posted a video of my bike with your brand turn signals, but they weren't on (FZ6R), I was showing the exhaust and the PCV running. I will post one with my RR when I'm done changing parts on it.

[@darksorceresszyra9467]

Udate: the 2003-2006 relay works on the 954RR. For anyone who is working on their 954 signals. Thanks TST!

[@rubenchaus925]

@@darksorceresszyra9467 I have a 954rr too, but I can't find the original relay, where is it located?

[@michaelbrown8320]

Will it work for 2003 cbr 954rr??

[@Dacowest]

Can i install it on a PC37 from 2003 ??

[@crimson20061]

One of the resistors went bad winch caused my right side blinkers to not work after a few seconds of flashing. Removed the resistors and installed the flasher relay and got perfect operation. This is my first bike so know that this installation is not "expert" level...

[@williamlivingston3577]

Does this LED flasher relay just correct the rear turn signals? If so, do you have any advice/suggestions to correcting the front turn signals that are attached to the fairings on a 2006 Honda CBR600RR? Thank you in advance!

[@williamlivingston3577]

Found video. Please disregard

[@gregg9448]

Does this LED relay take care of both front and rear blinkers? I just installed an undertail kit with LED's but they don't blink they just stay solid.

[@TSTindustries]

It does when the issue is the flash rate. Now you may have a different problem with your front signal wiring that could be the culprit if your front signals flash but rears don't. I recommend verifying that the running light circuit is not connected with the signaling circuit. In the front, on one side, the orange and orange/white should not be connected together. On the other side it is blue and blue/white.

[@WeeeklyBoom]

Soooooooo. I broke the locking clip on the blue plastic rectangular thingy with all the wires going into it. Would it be bad to keep it like that?

[@TSTindustries]

please send some detailed photos of how severe it is to our support email. I will then be able to give you advice on what to do.

[@drewswift2006]

Hi, so I own a 2006 cbr600rr and installed the tst turn signal pods and ended up with solid lights when I switched on my flashers. This lead to research and finding out about hyper flash and the gen 2-I tst flasher relay to remedy. I installed the relay as this video instructs but now when I flick on the flashers the running lights go off and I get nothing, no light at all, not even on the console and when I turn the flashers off the running lights come back on. I'm hoping ya'll might know how or why that is. I don't deny that this relay works, Im just scratching my head trying to figure out what may be wrong or what I may have done wrong. although I followed the video to a T.

[@TSTindustries]

It sounds like your front signals are wired incorrectly. If you have your running light and signal light wire jumped together into one connection this will cause your problem. Please check the connections on the front signals and find out if this is what the current setup is. If you disconnect the striped wire from the signal it will solve your problem. One side will have a blue/white stripe. The other will have an orange/white stripe. These are the ones that are supposed to not be connected.

[@williq4098]

I ordered the integrated Taillight for my 2003 cbr600rr with the relay and I want my break light flash few times before it Stayed solid I can’t find that video

[@TSTindustries]

The relay that you ordered corrects the flash rate of the signals. It has nothing to do with the brake circuit. The strobe alert function for the brake light needsa different module in order to function. We do not have a 03-06 600RR specific video for that part but the same method demonstrated in the 13+ video is used for installation. Below I will include the link to the product page and also the 13+600RR video. tstindustries.com/tst-brake-light-modulator-honda-oem-tail-lights.html kzbin.info/www/bejne/oZylZ3ibqtKKja8

[@ronaldguzman4196]

The plug on a 1000 is different, because the 1000 does have a relay, does it need to be replace by this one?

[@TSTindustries]

If you are referring to the 06-07 model year, then you can follow the link below to watch our installation on that bike: kzbin.info/www/bejne/bmqpdJ2vp7Bkm5I&t

[@tm96emi]

I f****** love you man ❤ you are my hero 🙏🙏🙏

[@TSTindustries]

Alright...I will take that.

[@Asvpscvtt]

Hey I had a question does the relay fix the issue when the turn signal stays on but does not signal

[@TSTindustries]

That depends on what is causing your signals to not operate correctly. I would need more info to answer your question. On some bikes hyperflash manifests itself in signal lamps staying on and the relay does restore the flashing.

[@ragnarhelgipetursson2584]

Great video! Will that work on my 2001 CBR 929? Previous owner installed led blinkers only in the back and some resistors. The blinkers hardly ever work. Will this relay solve that problem? Do I need to replace the front bulbs with led too? Thx :)

[@TSTindustries]

I believe you can install this on the 929 but it is likely it will have different color codes for the correct wires. You would have to remove the resistors from the rear. You don't ha e to change the fronts to LED, this relay will work front OEM, rear LED

[@henry3397]

@@TSTindustries Hi, what if you have the integrated light AND LED turn signals up front? I have the relay already, is the install shown only for the rear turn signals? Will I have to connect an additional two wires to the relay for the LED fronts to work properly?

[@TSTindustries]

@@henry3397 the relay is upstream of the lamps and the directional switch so it doesn't matter how many signals you changed. There is nothing else you will have to do. One relay takes care of all the signal lights, provided you have everything connected properly

[@TSTindustries]

@@henry3397 No, our relay corrects and controls the entire signal circuit.

[@anthonycurtis5693]

fixed my problem

[@TSTindustries]

Well that is great!

[@netotorres976]

Just putting this all the signal go to the back turn lights right ?

[@TSTindustries]

The relay controls all the signals, front and rear.

[@xNoName17x]

At first sorry for my bad english, but i hope you can help me. Im driving a Honda CBR 600RR built in 2003. The original relay is damaged... Problem its placed in the case of the speedometer so its heavy to change the original relay. My flashers dont flash, they only glow... Can i fix the problem if i install your LED flasher relay?

[@TSTindustries]

if the problem on your bike is caused by your relay then using ours will solve your problem. Our relay circumvents your OEM relay.

[@devici2521]

that reply gave an end to all my searching of relavent matter. Thanks a lot guys!!!

[@AlvlUpSavedMyLife]

Does this also fix if they are not flashing at all? They just stay on and don’t blink. Front LED and read taillight LED. It’s a 05 cbr600rr... please help!!!

[@TSTindustries]

If they aren't flashing at all you may have a wiring issue and a relay would not fix that. The 600RR has a running light and a signal light circuit in the front signals. I have seen people use a single circuit signal lamp and jump the running light and signal light wires together to the positive side of the signal lamp. All this does is run continuous current through that lamp it's connected to and also the rear one because the running light circuit is constantly on. Please check your front signals to see if maybe they are wired in this way. If so, just disconnect the wires that have the white trace on them. That will be blue with white trace on one side, and orange/white trace on the other side.

[@AlvlUpSavedMyLife]

TSTindustries oh my gosh thank you soooooooo much. This worked!!!! I love you guys!!! Subbed!!

[@TSTindustries]

@@AlvlUpSavedMyLife From time to time an opportunity to help a fellow rider presents itself and I jump right on it. I got into this business to help people have a better experience with their bikes. It pleases me to fulfill my mission. Thanks!

[@atheerismail1838]

great jop

[@johngavin1343]

Hi what is the code on the relay ,where to buy this from an I have just got led signal mirror will this fix both them an rear tail intergrated light?Thanks for your time Regards John. It is a 03 cbr 600 rr .

[@TSTindustries]

Yes, this relay will control all your signaling equipment, front and rear, right and left. The presenter in the video is the person who designed the relay. The company that manufactures and sells the relay made this nice video for you to know how to install it and where to purchase it. The link to the product page is actually in the description of this video. Here is a link to the product category for all the parts we have for 03-05 600RR : tstindustries.com/honda-cbr-600rr-2003-2006/

[@PABLOESCOBAR-ph3el]

Hey I got a question. Do you need the relay to prevent future problems with the electrical on the bike or its just personal preference.

[@TSTindustries]

Ismael Chavez having a faster flash rate does not damage the electrical system on your bike. it may confuse some drivers as to what you are signaling and that is why we provide our relays. They enable you to get a standardized flash rate for your signals. But in the end, as with anything, the choice is yours.

[@PABLOESCOBAR-ph3el]

TSTindustries thank you for your reply. I was just wondering cause my new tail light is fast but it's not as bad it actually looks good. And I hate to mess with the original harness of the factory. Thanks for your help

[@TSTindustries]

Ismael Chavez glad to help buddy. If you ever change your mind and need a flash control device then you can rely on our relay not having to be wired in...all plug and play. But it sounds like you have it handled for now. Ride safe.

[@PABLOESCOBAR-ph3el]

TSTindustries yes I been thinking about it. I will definitely get one from you guys. Thank you. Your channel has helped me lots.

[@DJREDLINE305]

Will this work for a 2009 cbr 600rr

[@TSTindustries]

DJ REDLINE essentially yes but with a much simpler installation. Please see our product page for that part and see the appropriate video in the videos tab tstindustries.com/TST-LED-Flasher-Relay-Gen2.html

[@08mrwright]

is this harness good with a f4i

[@TSTindustries]

Yes indeed.

[@nathanesquibel7687]

I'm having trouble with the fastner that's on the inside it just keeps spinning hand won't come out?

[@TSTindustries]

you need to specify which fastener so I can answer your question. You can give me the time stamp in the video where it is shown.

[@nathanesquibel7687]

+TSTindustries it's at 1:22

[@TSTindustries]

+Nathan Esquibel OK. You can hold the perimeter of the fastener with your fingers and turn the center part counter clockwise a quarter turn without putting pressure on it. The center will pop out and you can then remove the entire fastener.

[@walterbaldwin3643]

So I have an 03 honda cbr 600rr and I just installed flush mount blinkers. They are both on but when I go to signal left it shuts off the light and when I signal right it does the same thing will this fix that problem? Thank you in advance

[@TSTindustries]

It sounds like you have your signals connected improperly. The Honda has two circuits in each front signal lamp. They are the signaling circuit and running light. If your front signals are a one circuit type of lamp, and you connect both running and signal circuit to them, then you would get the symptom you described. You need to disconnect the running light wire from your signals. On one side it is orange with white stripe, and on the other it is blue with white stripe. Disconnect those and let me know what happened.

[@walterbaldwin3643]

@@TSTindustries I got it connected thank you for the reply!!!

[@TSTindustries]

@@walterbaldwin3643 glad to help.

[@TSTindustries]

@@walterbaldwin3643 was it what i thought it was?

[@walterbaldwin3643]

@@TSTindustries well that was from before I bought the tst relay so I didnt know I needed the relay to make the lights blink. Thank you for the quick responses and informative videos I will definitely be looking at anything else you guys have. Was wondering if you guys had exhausts?

[@vig6912]

will this work if the leds stay off?

[@TSTindustries]

Would you mind elaborating a bit more?

[@ledzeppelin175407]

How do you know which wires to disconnect??

[@TSTindustries]

You apparently did not watch and listen to the entire video. All of that is explained.

[@Nico-xy4cb]

how can I install the relay on my 2004 cbr 600 if I don't have a blue connector? no I'm not blind I followed the wires from the blinkers front to back and there is no blue connector

[@TSTindustries]

I don't know man. I have worked on many, many 03-06 600RR's and they all had that connector. If you were local I would just say bring it in so I can help you.

[@elic3395]

When I tried to install the relay I had some problems, the first when I tried to remove the cables in my motorcycle were of another color (different to that you show it in the video), the second when I was trying remove them, one of them it broke up and the pin got stuck, the third, to despite to cable was broken I tried to install the relay and it did not work. Also I had problems with the integrated tail light because my motorcycle have not the pin (and in the video only connect the pins for each of directional lights and it is not like that when only have the cables without pins). I am not happy because the relay not work and the integrated tail light also not work without the relay, you should consider this kind of problems in the instalation.

[@TSTindustries]

first let's address your taillight issues. Our units are pre-fit with OEM plugs for ease of installation. If you, or the bike's previous owner cut off the plugs then your bike is modified beyond OEM spec and will require harness side plug replacement, or you will need to hardwire the taillight in. If you would like us to help you with information on how to accomplish that you can contact our specialists through the support tab on our website. Even if the fault with the installation is not caused by our equipment we do our best to help our customers because that is how we run our business. We are a riders-for-riders kind of place.

[@TSTindustries]

Now let's delve into your relay woes. This system we sell and have illustrated in this video has been developed by an engineer, verified for use on a few local bikes, and validated in the field by hundreds of end users who have already put this system to good use. Surely we can figure out what went wrong with your installation if you contact us through the support tab on our site.

[@darksorceresszyra9467]

I broke the blue clip clasp too, but it will still go back in if the same flimsy hanger/hinge broke on yours too.

[@bog327]

Please help. Someone here can help find a solution with a set of built in relay led blinkers on a 2008 Hornet? With the original relay on the bike, they won't work at all. On the web it seems impossible to find a dedicated relay for this type of blinkers. Please, if you know a tutorial on how to resolce such issue...or any kind of info or advice. Thanks!

[@TSTindustries]

Well it appears as though we did not have a 2008 Hornet here in our market. The closest I found in available documentation here is the 2006 CB600F. According to part documents, this bike uses a standard flasher relay for signal flash switching, and it is located under the tail components on the left side of the bike, just fore of the ECU. On this bike our RLY-G2 model relay is the appropriate replacement component . After that year the CB600 model did not re appear for us but CB500 and 650 models did a few years later. Those bikes used our RLY6 relay. I would suggest pulling your OEM relay out and comparing the shape of the connector to the images of the relays that i mentioned on our website tstindustries.com . If it is a match then that is the part you will need

[@bog327]

@@TSTindustries thanks a lot for the fast answer. I took a look at the RLY6 relay you mentioned and by the number of pins and the hole design of it, seems to be the one i need. The two questions remaing are: 1. It will make the blinkers with the integrated relay work sequentially like they do directly on the battery or it will make them only blink? and 2. Do you have any seller of your products in Europe ? Thanks again!

[@KEETHZERO0368]

What year is this bike that you're working on in this video?

[@TSTindustries]

It is a 2003 with 2006 fairings.

[@dujuanjohnson5025]

where did you get the fairings? thanks

[@EnjoyCalculus]

Stock relay doesn't have to be removed?

[@TSTindustries]

There is no stock relay on this bike. The flasher circuit is integrated into the bike's dash. Our product circumvents the bike's dash circuit.

[@EnjoyCalculus]

TSTindustries ordered off eBay. Thanks

[@sufyan2047]

Is this the same proceeder for the 1000rr 2007

[@TSTindustries]

+sufyan2047 The installation procedure for that model year bike can be viewed here: kzbin.info/www/bejne/bmqpdJ2vp7Bkm5I

[@sufyan2047]

+TSTindustries thanks mate. Also have you got a video for the 1000rr brake stroke flasher

[@TSTindustries]

I think you mean strobe flasher. We currently do not offer that part so we don't have the video. We have had a number of customers ask for that part so maybe we will design one soon.

[@91TwinTurboZX]

Would this work if the turn signals doesn't flash at all?

[@TSTindustries]

Maybe. It depends on what caused your signals to stop flashing. If you message our support guys through our site they will help you determine the cause of your problem and how to fix it.

[@ahmadodeh5776]

91TwinTurboZX That was my problem also, decided to just buy it and installed it yesterday and it solved my issue.

[@hornick12ify]

2WheelM4yh3m was your signals just soild yellow when you turned them on?

[@ahmadodeh5776]

Yeah, this relay solved it.

[@chillduc1]

Is that the same procedure for a cbr1000rr 2004???

[@TSTindustries]

sébastien duclos the installation on your motorcycle uses a different but easier procedure. Your bike has the relay in between the headlights. It requires a different relay that can be found on this product page tstindustries.com/Honda-CBR-1000RR-2004-2007/

[@chillduc1]

TSTindustries Thanks for the fast reply! Do you have a video that show the procedure?

[@TSTindustries]

Unfortunately we do not. We have 2006-2007 but the relay location on that bike is different than 2004-2005. I found a video in Deutch that showes where the relay is with the upper fairing taken off. I hope that helps you. kzbin.info/www/bejne/qH6zeKVtlreCpbs

[@chillduc1]

TSTindustries Thank you verry Much guys 👍

[@chagojerome3795]

Where u buy the flasher relay?

[@TSTindustries]

From the company that produces it and made this video to help you install it ---> tstindustries.com

[@Garilla74]

Where is the link to buy exact part.

[@TSTindustries]

In the description.

[@Garilla74]

@@TSTindustries I saw it after I clicked in description I’m sorry. Just ordered both the tail light and relay. Thank you very much

[@isaema3566]

My plate light flicker and right rear signal won't turn on, can this product fix that?

[@TSTindustries]

If your plate light flickers then you have a wiring issue outside of the signaling circuit. The flasher relay will not do anything to fix that. If your rear signals don't turn on but the front signals do then changing the relay will do nothing to help you. I would advise you to examine the wiring on the rear of the bike and make sure all lighting components are wired properly. You can then move upstream to relay and switches.

[@isaema3566]

@@TSTindustries I am considering buying the the tst signal break with the relay and plate light. Think will be ok if I actually replace my lights with yours? Thanks for the help?

[@TSTindustries]

@@isaema3566 I do believe that if you use our components, and if you connect them to your bike properly, and if your bike does not have upstream wiring problems, then you will have a properly working setup.

[@isaema3566]

@@TSTindustries any discount if I buy everything from light to relay to fender eliminator? Wow day responses

[@TSTindustries]

Our website pages have a"Buy Together" module that appears below the add to cart button and enables you to bundle products for savings.

[@geet77777]

there should be a video on getting the wire out of the blue plug. im about to light this bike on fire.

[@TSTindustries]

I don't get it....we show the procedure in great detail starting at 2:38 in this video

[@geet77777]

@@TSTindustries it was the little tab inside, just didnt want to release. most of these connections are pretty old at this point. kinda mucked it up getting it out but now its all good and the flasher works perfectly.

[@TSTindustries]

Glad you got it figured out.

[@AlvlUpSavedMyLife]

LOL

[@mikeward4624]

So I did this exactly like you did . But now my rev gauge arm won't move i can put the gray back in and it work?? Anyone have this problem? Tst industries if you read this i need help . I only got this as your the only place I wont have to splice .

[@TSTindustries]

You must have pulled out the wrong wires. That connwctor has many functions in it and if you get the wrong pin out you will kill that function. Please put everything back to how it was and then restart. Do every step one by one with the video and the commentary within it in front of you for reference. If you need more help after that please reach out to our customer service department through our website during business hours.

[@seahawksforever9504]

Dislike for not telling what is green wire and what is grey wire.

[@jim6821]

will this work if the leds stay on?

[@TSTindustries]

It depends on what is causing them to stay on. Typically if there is not enough current draw in the signaling system the OEM relay will either hyperflash or just keep the lights on. If you have changed your signal lamps to LED and that is what caused your signals to stay on then our relay will be your solution.

[@jim6821]

ta buddy yes they where working fine before the led I will have to buy one going to the UK