How to Install Rear LED Pod Turn Signals on 2024+ Yamaha MT-09 by TST Industries

[@Itsyunlo]

Is there a video showing the wiring? All of the wire colors are different on the mech evo rear signals vs the plug n play as well as the oem connectors.

[@TSTindustries]

@@Itsyunlo 38:25 starts going over the wiring for the Mech-EVO set-up

[@Dingy099]

I'd like to get a fender eliminator, but on my Gen2 the turn signals got in the way of putting saddlebags on 😢

[@diggy-d8w]

How many times has the Fz/MT ~ 09 changed over the years? I guess I could digg it up but I guess TST makes this tiddy kit for each version? It is pretty sharp looking..... I had to add to this post, great job in how you guys are addressing the issues that cause lots of returns. Handling it in modular's & getting people to think about things ahead of time ought to save your company & riders a lot of money in returns/delivery... thinking about it carefully saves everyone. Nicely done, all of it. peace

[@TSTindustries]

@@diggy-d8w there are 4 different generations and we have a full suite of products for each one!

[@diggy-d8w]

TY so much ~ sharp looking

[@damacknificent151]

I like the low mount but if it had integrated turn signals. Also, can high mount have original turn signals with adjustable license plate?

[@TSTindustries]

@@damacknificent151 absolutely, that’s the first variation we show of assembly.

[@damacknificent151]

@@TSTindustries which one? High mount with adjustable plate and original turn signals?

[@TSTindustries]

@@damacknificent151 that is correct. I’m not sure exactly what you mean by integrated signals with a low mount but we do have plans on designing and releasing an integrated tail light sometime next year.

[@damacknificent151]

@@TSTindustries yes, integrated into tail light plus low mount might be better option compared to low mount and turn signal next to it that might have me nervous my girl's might actually kick off accidentally

[@TSTindustries]

@@damacknificent151 we do plan on releasing one but it won’t be until next year at the earliest.

[@ZukaBro]

Not mentioned the whole would be open under your fender for water an dirt an everything else to get thrown up there or am i worng?

[@TSTindustries]

@@ZukaBro no, with our undertail closeouts all holes are covered. The only “holes” you may have are the tiny ones from drilling our center closeout for wire routing. But that’s very minimal and wouldn’t allow too much debris, if any at all, from entering your tail compartment.

[@WheresWagner]

got my kit in today and am installing it, there are parts on the side of the closeout that you would drill/cut out and it leaves enough room for the turn signal cables to route through without a huge hole

[@ZukaBro]

@@WheresWagner can you show me how much wire you can see after the wires are routed through the close out?

[@WheresWagner]

@@ZukaBro you can have as much or as little as you need.

[@thasherm]

Around 30:45 for the OEM Signal/Adjustable High Mount in these instructions you didn't install the two push pins that connect the undertail to the bottom of the rear brake light. Was that expected?

[@TSTindustries]

@@thasherm yes, that process was just shown to illustrate how it would mount but the full reassembly process should be followed with putting all hardware and fasteners back in place.

[@thasherm]

@@TSTindustries I figure it was probably hard to make a video with so many different options people can choose to go with. I ended up watching this video and the adjustable high mount video ( kzbin.info/www/bejne/p17TdoqDr9d3oLc ) in combination and it worked out well. Looks great! Kudos to the R&D team and the techs who made the videos 💪🏻

[@ZukaBro]

So if ypu use the oem turn signals on the high mount bracket adjustable or none, the wires are exposed ? Those wites are thick. So it def be seen an a very ugle fit.

[@TSTindustries]

@@ZukaBro no, the wires are tucked behind our license plate bracket and then routed into the undertail through our center closeout.

[@HassanIsDriving]

@@TSTindustries so basically you would have to make a bigger hole with a drill in order for you to tuck the OEM turn signal lights inside.

[@TSTindustries]

@@HassanIsDriving no, the same size hole is needed to remove the breakaway pieces from the center closeout we provide. You only need to route the wires through the cut-outs, not the connectors. If you need more assistance or visuals, please email our Support Team. We show the process in this video but if something isn’t clear enough, we can provide additional material through our Support Team.