Build your own custom Tube Bender Stand, check this video out: kzbin.info/www/bejne/gIGnoGevr7iGmqs
@porschmn2 жыл бұрын
I sure get it, these dies aren't cheap and like you say if it were production or you did a lot of bending yeah buy one, but in a pinch or for a few bends this is a great idea, thanks for the tip.
@RathaSochenda2 жыл бұрын
Yessir
@abbbyt2 жыл бұрын
Awesome bro
@gk94532 жыл бұрын
Nice! Good info. Love your builds, Brother. Can’t wait to see what you build next!
@RathaSochenda2 жыл бұрын
Thanks!
@sddiymakeitworthit75122 жыл бұрын
That’s awesome video man congratulations 👍
@RathaSochenda2 жыл бұрын
Thank you
@modificationnation732 жыл бұрын
Nice. Good for one or two bends.
@RathaSochenda2 жыл бұрын
Depends how many sleeves you make. Normally one bend per sleeve
@dragade1012 жыл бұрын
I like your solution. Maybe certain dies (sets) will not like to bend more material but for thinner walls; this probably works just fine in the long term.
@RathaSochenda2 жыл бұрын
Yeah I’ll have to try this on other dies one day with thinner wall.
@FishingPhoFun2 жыл бұрын
Love this trick with my tube bender. Great content! San sent me here! Let me know if you need to borrow dies I have a few
@RathaSochenda2 жыл бұрын
Thanks for stopping by! For sure man I appreciate it. I know them dies can be $$$
@FishingPhoFun2 жыл бұрын
@@RathaSochenda of course! Keep up the great content and yea the dies are money. Ha
@RathaSochenda2 жыл бұрын
Thanks bro 🙏🏽
@baldeaglegarage2 жыл бұрын
Very resourceful, nice vid!
@RathaSochenda2 жыл бұрын
Glad you found it helpful
@ChristophLehner2 жыл бұрын
Great video as always👌
@RathaSochenda2 жыл бұрын
Appreciate it
@neleig2 жыл бұрын
Very useful info.
@RathaSochenda2 жыл бұрын
🙏🏽
@Vkandypaint2 жыл бұрын
Great video and info👍🙏
@xavior7182 жыл бұрын
What if you make a removable sleeve that’s shaped and fitted onto the die and follower? Like a spacer so you wouldn’t have to make a sleeve per bend.
@RathaSochenda2 жыл бұрын
That’s a good idea. I’ll give it a shot. Make an adapter sleeve for the follower and the die. Just need to make sure to weld in som tabs to keep it from sliding off.
@grandpafabio2 жыл бұрын
@@RathaSochenda It's a good hack, and as you pointed out it's way cheaper than dedicated dies. I made the removable sleeves described above for my JD2 Model 32 a few yrs ago. Allows 1-3/4 die to bend 1-1/2 through 90 degrees, I've probably used it 20X and it works great. Only thing I noticed was sleeve on my (mild steel) outer sliding die was showing a bit of scoring after a few uses, however I now use a thin coat of EP grease on the outside radius of tube being bent... problem solved.
@luctessier22152 жыл бұрын
What CLR is our die?
@RathaSochenda2 жыл бұрын
It’s 5.5
@fmxq82 жыл бұрын
👍🏼
@dragade1012 жыл бұрын
Do you always wear synthetics in your shop? I prefer clothes that will just burn when exposed to heat and not clothes that shrink up like electrical shrink wrap. Leather is the only exception because is thick enough, that incidental heat will not instantly bind the glove to your hand (thus intensifying the burn if you cannot remove clothing that has confirmed to your body perfectly).
@RathaSochenda2 жыл бұрын
Good call I should probably where something safer.
@dragade1012 жыл бұрын
@@RathaSochenda even jeans and a cotten hoodie are better
@andrel32 жыл бұрын
What belt grinder are you running? The house work one?